How to replace the front wheel on a Kia Sorento?
Remove the coking nut (A). The front hub coking nut should be replaced with new ones. After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below. 4. Remove the brake hose (A) and wheel speed sensor (B). 5. Remove the tie rod end ball joint (C) from the knuckle. Remove the split pin (A).
What are the traction lights on a Kia Sorento?
Re: Abs,esc and traction lights on 2011 Kia Sorento all… You can’t post conmments that contain an email address. 2012 Soul. Why does it continue running even when ignition switch is turned off? 2015 Rio. Where is the E/R junction box?
Why does Kia Sorento have ABS and ESC?
An expert that got 10 achievements. Re: Abs,esc and traction lights on 2011 Kia Sorento all… You can’t post conmments that contain an email address. 2012 Soul. Why does it continue running even when ignition switch is turned off? 2015 Rio.
How to remove the coking nut on a Kia Sorento?
After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below. 4. Remove the brake hose (A) and wheel speed sensor (B).
What kind of wheel assembly does Kia Sorento use?
Kia Sorento 2011, Wheel Hub Assembly by Quality-Built®. MPA 100% new wheel hub assemblies feature OE bearing design, integrated G111 induction hardened, raceway technology and heavy duty seal design for consistent quality and performance. Kia Sorento 2011, CV Axle Assembly by GSP North America®.
Which is Kia Sorento axle shaft by surtrack?
Kia Sorento 2011, CV Axle Shaft by SurTrack®. This product features a brand new construction with precision machined and heat treated center-shafts, CV joints, bearings and races. The CV axle shaft by SurTrack is manufactured with high… Kia Sorento 2011, CV Axle Assembly by First Equipment Quality®.
How do you remove a CV axle from a Kia?
Wiggle the knuckle off, or place a pry bar between the strut and the knuckle until they are separated. Push or tap the CV axle shaft through the wheel hub until the two are separated. III. Removing the CV Axle From the Transmission Remove the splash guard that covers the crank shaft and harmonic balancer.
Can a pry bar be used on a Kia Sorento?
Use a pry bar being careful not to damage the transaxle and joint. Do not insert the pry bar too deep, as this may cause damage to the oil seal. Do not pull the driveshaft by excessive force it may cause components inside the joint kit to dislodge resulting in a torn boot or a damaged bearing.
Remove the coking nut (A). The front hub coking nut should be replaced with new ones. After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below. 4. Remove the brake hose (A) and wheel speed sensor (B). 5. Remove the tie rod end ball joint (C) from the knuckle. Remove the split pin (A).
What kind of tires are on 2012 Kia Sorento?
The following is from an E-mail sent to big O tire customer service (tbc Corp) on June 26/2014 we own a set of 4 defective cooper 107H discoverer lsx plus tires purchased for our 2012 Kia Sorento ex SUV on Nov. 29, 2013 from big O tires store #6171 in conifer, co. They balanced and mounted the tires.
Are there any problems with the Kia Sorento suspension?
I did some research and found numerous other complaints about suspension system on this model Kia Sorento. I provided this information to repair shop and returned for proper fix. They discovered a technical service bulletin for this car #SA178. They made this correction and told me to contact Kia for reimbursement.
After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below. 4. Remove the brake hose (A) and wheel speed sensor (B).
How do you remove a Kia Seltos emblem?
Here are a couple of videos from one of our customers installing emblems on their 2021 Kia Seltos: (note, you need to remove the four screws on the rear tail light assemble to completely remove the piece. Once that is done, it’s easy as the KIA emblem unscrews and just pops out.
Use a pry bar being careful not to damage the transaxle and joint. Do not insert the pry bar too deep, as this may cause damage to the oil seal. Do not pull the driveshaft by excessive force it may cause components inside the joint kit to dislodge resulting in a torn boot or a damaged bearing.
How to replace the front drive shaft on a Kia Sorento?
Remove the brake caliper mounting bolts, and then place the brake caliper assembly (B) with wire. 3. Remove the coking nut (A). The front hub coking nut should be replaced with new ones. After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below. 4.