How to adjust spindle torque on C3500 diesel?
– Tighten nut to 12 ft lbs while turning the wheel forward by hand. This will seat the bearing. – Adjust nut to a “just loose” position by hand, then back the nut off until the hole in the spindle aligns with the slot in the nut. DO NOT BACK THE NUT OFF MORE THAN A 1/4 TURN.
What happens if your spindle nut is over torque?
It will also leave your spindle nut under or over torque resulting in hub assembly failure. Ensure that you have the correct torque for the application by referring to SKF 457377 torque specification guide or contact the vehicle manufactures dealer. It is important that you properly torque the spindle nut to ensure optimum bearing life.
Do you need a calibrated torque wrench to install an axle nut?
To guarantee the (Bearing, Spindle or Hub) is torqued correctly, follow the manufacture’s installation procedure. Ignoring these important details will reduce the life of your (Bearing, Spindle or Hub). Use a qualified, calibrated torque wrench. Do not use an impact gun to install the axle nut. The impact gun will damage the axle nut.
How to adjust the rear wheel bearing torque?
Rotate the hub in the opposite direction to the way the adjuster nut is turning. Ensure the inner bearing and the seal seats against the spindle shoulder. Tighten the adjusting nut to 70 N-m (52 lb ft). 6. Turn the adjusting nut counterclockwise and align the closest lock key slot with the keyway in the axle housing.
– Tighten nut to 12 ft lbs while turning the wheel forward by hand. This will seat the bearing. – Adjust nut to a “just loose” position by hand, then back the nut off until the hole in the spindle aligns with the slot in the nut. DO NOT BACK THE NUT OFF MORE THAN A 1/4 TURN.
It will also leave your spindle nut under or over torque resulting in hub assembly failure. Ensure that you have the correct torque for the application by referring to SKF 457377 torque specification guide or contact the vehicle manufactures dealer. It is important that you properly torque the spindle nut to ensure optimum bearing life.
To guarantee the (Bearing, Spindle or Hub) is torqued correctly, follow the manufacture’s installation procedure. Ignoring these important details will reduce the life of your (Bearing, Spindle or Hub). Use a qualified, calibrated torque wrench. Do not use an impact gun to install the axle nut. The impact gun will damage the axle nut.
Rotate the hub in the opposite direction to the way the adjuster nut is turning. Ensure the inner bearing and the seal seats against the spindle shoulder. Tighten the adjusting nut to 70 N-m (52 lb ft). 6. Turn the adjusting nut counterclockwise and align the closest lock key slot with the keyway in the axle housing.
What should the EndPlay be on a C3500 dually spindle?
If you have the capability… Measure the endplay in the hub/rotor asembly. Correct endplay should measure 0.03 to 0.20mm (0.001″ to 0.008″). Hope that helps. Good Luck. Pack the bearings and install inner bearing and seal and slide hub on spindle. Then install packed outer bearing,washer and nut finger tight.
What was the factory manual for a Chevy truck?
1948-1953 Chevrolet Truck Factory Shop Manual Covering the following Chevy Models: 3100 Pickup, 3100 Cab & Chassis, 3600 Pickup, 3600 Cab & Chassis, 3700 Cab & Chassis, 3800 Pickup, 3800 Cab & Chassis, 3900 Truck General Motors…
What was the factory manual for a 1936 Chevy?
1935 1936 Chevrolet Car and Truck Factory Shop Manual Covering the following Chevy Models: Master Deluxe, Pickup, Sedan Delivery, Standard, Standard Truck Complete Volume | General Motors Corporation | *NOTE: This is an Factory Authorized…
What kind of transmission does a C3500HD have?
Transmission offerings were the 4L80E 4spd OD automatic, and the NV4500 5spd OD manual, these were the only two transmissions ever offered for the C3500HD. The common drive axle used on the C3500HD was the Dana 80, an 85.8″ wide full floating axle with an 11 inch ring gear.
What kind of truck is a Chevy C3500?
This Chevy utility bucket truck has a working Altec boom lift attached, a new front end, and tool boxes with plenty of storage…. BEAUTIFUL 2015 REG CAB CHEVROLET SILVERADO C3500 HD WITH 12′ STAKE BED.AM/FM STEREO. ICE COLD AC!! LOOKS AND RUNS GREAT!!! CLEAN CARFAX!!! NO ACCIDE…
How many miles does a 2002 Chevy C3500 have?
2002 Chevrolet c3500 cutaway 16ft box truck 138k miles, 6.5 turbo diesel, Auto, rear/side door, no leaks, perfect for any job, load ramp, no CDL!… CHIPPER DUMP WITH A CUP! BUY HERE PAY HERE WITH ABOUT $5000-7500 DOWN (OAC) 2001 C3500, 8.1 GASOLINE CALIFORNIA SMOG COMPLIANT, 123,294 MILES. 10 1/2
Is the crew cab available on the C3500HD?
The C3500HD came with regular cab as the only cab option until 1996, when the crew cab was also offered, it is not clear if the crew cab could only be ordered for fleets only, or if all consumers could order it as well. The extended cab was never offered on the C3500HD. All cabs came standard with upper marker/clearance lights.