How many miles does a Jeep Cherokee need to drive?

In order to make the monitors READY or COMPLETE you’ll need to drive your Jeep Cherokee in a specific drive pattern, known as a Jeep Cherokee Drive Cycle. Typically driving 200-300 miles over the course of a week and in both city and highway traffic is enough to complete the monitors.

What to do if your Jeep Cherokee turns off while driving?

Try changing the throttle position sensor located on the throttle body. Pull throttle body off 4 bolts disconnect the 3 wires clean throttle body with throttle body spray or carb spray. Spray the other sensor clean to a shine. My jeep was doing same thing no more problems.

What are the pre conditioning requirements for a Jeep Cherokee?

1) Cold soak vehicle, start and idle vehicle for 4 minutes. 2) Drive in-town (stop and go) for 5 minutes, using smooth acceleration and deceleration. 3) Stop and idle vehicle for 4 minutes. Pre-Conditioning Requirements: – MIL must be off. 1) Idle vehicle for five minutes (to reach closed loop operation).

What kind of sensors are on a Jeep Cherokee?

New Parts Plugs,Wires, Distributor, Coil, Battery, Alternator, Fuel Pump, Crank Position Sensor, Idle Air Control Sensor, Air Exhaust Temp Sensor, Throttle Position Sensor. The only other things I can think of is junk auto-zone parts, Short on wiring harness, or computer.

How many miles does a 1999 Jeep Cherokee have?

Mileage: 200,000 miles Body Type: SUV Color: Purple Engine: 6 Cyl 4.0 L Rebuilt title issued|Salvage title issued. 1st owner purchased on 03/26/99 and owned in TX until 07/06/06 • 2nd owner purchased on 07/06/06 and owned in TX until 08/10/18 • 3rd owner purchased on 08/10/18 and owned in OK until .

How to find the correct tire size for a Jeep Cherokee?

Jeep Cherokee – Specs of wheel sizes, tires, PCD, Offset and Rims – Wheel-Size.com Jeep Cherokee – Find out the correct alloy wheel fitment, PCD, offset and such specs as bolt pattern, thread size(THD), center bore(CB) for all model years of Jeep Cherokee. Choose a model year to begin narrowing down the correct tire size

When was the last time I serviced my Jeep Cherokee?

Last serviced at 149,594 miles in Santa Fe, NM on 01/25/20 • Vehicle serviced • Maintenance inspection completed • Oil and filter changed. No accident or damage reported to CARFAX. Purchased on 01/28/99 and owned in TN until .

Is there a problem with my Jeep Grand Cherokee?

Very often, this will solve the problem. But Jeep Grand Cherokees seem especially prone to more serious transmission problems, and some owners are quite vexed at their inability to determine the causes.

Can a Jeep Grand Cherokee Drive in two gears?

You’re often still able to drive the vehicle, but it only operates in one or two gears. For example, you may find that you’re only able to drive the car in the automatic transmission’s third gear, only being able to select the other two gears when you shift the transmission manually.

Why does my Jeep death wobble when I drive?

“Death wobble is caused by something very simple – it’s the vehicles inability to absorb the natural vibration caused by driving,” says Mike Gardner, longtime Jeep enthusiast, vintage Jeep expert and co-host of Willys restoration show ‘Throwing Wrenches’. “This problem can be in the front suspension or in the steering.

What kind of car is 2008 Jeep Grand Cherokee?

Used 2008 Jeep Grand Cherokee Expert Review. The Grand Cherokee is legendary for its rugged off-road capability, sensible size and car-like ride and interior. While most SUVs have grown to near-gargantuan proportions, the 2008 Jeep Grand Cherokee remains true to the general size of the original 1992 model.

Why does my 2002 Jeep Grand Cherokee not start?

SOMETIMES VEHICLE (2002 JEEP GRAND CHEROKEE) WON’T START. YOU GET NOTHING WHEN YOU HIT THE KEY, NO CLICKING, NO NOTHING. YOU MAY GO BACK LATER AND IT WILL START. GAUGES GO CRAZY. WILL COME ON. ODOMETER AND CLOCK WILL FLASH. SOMETIMES SPEEDOMETER WILL GO FROM 60 TO ZERO AND BACK. WILL NOT LOSE POWER THOUGH.

Is the Jeep Grand Cherokee a good car?

The 2008 Jeep Grand Cherokee retains the off-road capability of its forefathers, and rates high in the areas of ride comfort, steering and handling. However, on the ones we drove, at least, the brake pedals felt somewhat soft and seemed to need to travel quite a distance before attaining the desired affect.

Why does my Jeep Cherokee turn off while driving?

IF it just quits while going down the road, or if it starts running rough while at an idle then quits it could be this problem. It will also crank right back up sometimes or it may take 10 minutes or longer. To correct the problem remove the reservoir on the passenger side. The computer mounts to the firewall directly behind the reservoir.

What kind of drive system does a Jeep Cherokee have?

We will start with the Active Drive system, available on the Jeep Renegade and the Cherokee. This system requires no input from the driver, and it comes with a set of sensors that determine whether to send power to the rear wheels or just to the front axle.

Which is the 4WD system for the Jeep Wrangler?

The Active Drive Lock comes as standard for the Cherokee Trailhawk. It represents an evolution of the Active Drive 2 and features an extra mechanical real axle lock. The crawl ratio is maintained and the system also benefits from Jeep’s “Trail Rated” guarantee of off-road performance. 4WD Systems for the Jeep Wrangler

How to reset your Jeep Wrangler drive cycle?

Jeep Wrangler, Cherokee DRIVE cycles. How to reset your readiness monitors to pass emissions. – YouTube Jeep Wrangler, Cherokee DRIVE cycles. How to reset your readiness monitors to pass emissions. If playback doesn’t begin shortly, try restarting your device.

How long does a Chrysler Drive Cycle take?

Chrysler & Dodge: Drive Cycle Procedures to complete OBD Readiness Monitors. Pre-Conditioning Requirements: 2) Drive (with steady throttle) at a speed between 40 and 60 mph for 8 minutes. 3) Stop and idle for 3 minutes.

When did the Jeep Cherokee get two wheel drive?

In mid-1985, a two-wheel-drive version of the Cherokee was added to the lineup. This marked the first time any Jeep product was offered with two-wheel drive since 1967, and was done in the hopes of attracting a few more buyers who did not need (or want to pay for) four-wheel drive.

When did the Jeep Cherokee get a new intake manifold?

In the middle of the 1999 model year, vehicles with the 4.0 L engine received a revised intake manifold. This was done to help counteract smaller exhaust porting on the latest casting of cylinder heads, which was done to meet more stringent emissions control laws.

What was the first full size Jeep Cherokee?

Sharing the name of the original full-size Cherokee SJ model, the 1984 XJ Cherokee was Jeep’s first all-new vehicle design since the 1963 SJ Wagoneer, was the first American off-roader built with fully integrated body-and-frame ( unibody) design, and became the mechanical basis for the MJ -series Jeep Comanche pickup truck (1985–1992).

How many miles does a 1998 Jeep Cherokee Drive?

1st owner drove an estimated 16,192 miles/year • 2nd owner drove an estimated 0 miles/year • 3rd owner drove an estimated 0 miles/year • 4th owner drove an estimated 0 miles/year • 5th owner drove an estimated 7,262 miles/year • 6th owner drove an estimated 7,323 miles/year.

Where was the 1998 Jeep Cherokee last serviced?

1st owner drove an estimated 8,531 miles/year • 2nd owner drove an estimated 0 miles/year • 3rd owner drove an estimated 28,505 miles/year • 4th owner drove an estimated 640 miles/year. Last serviced at 201,834 miles in Cumberland, MD on 08/13/18 • Vehicle serviced. Rebuilt title issued|Salvage title issued.

When do I need to complete the drive cycle?

Turn on the ignition to ON, but do not start the engine. The check engine light f the (MIL) will turn on for 15 seconds. After 15 seconds, one of two things will happen. If the MIL flashes for 10 seconds, and then returns to being fully illuminated, the OBDII sensors are NOT READY and you need to complete the drive cycle.

How long does a drive cycle take in a Chrysler?

For all drive cycles, make sure the check engine light (MIL) is off. Smoothly acceerate and maintain a speed between 40 to 60 mph for 8 minutes. Stop and idle for 3 minutes. Smoothly accelerate and maintain a speed above 20 mph for 2 minutes.

What is the drive cycle on a Ford?

Newer Ford owner’s manuals include a drive cycle, which is as follows: The OBD-II system is designed to check the emission control system during normal driving. A complete check may take several days.

What’s the drive cycle procedure for a Dodge?

Driving Procedure 1) Warm engine up for five minutes (must reach closed loop) 2) Drive (with steady throttle) at a speed between 40 and 60 mph for 8 minutes. 3) Stop and idle for 3 minutes.

How to do a closed loop drive cycle?

1) Idle vehicle for five minutes (to reach closed loop operation). 2) Drive with a steady vehicle speed above 25 mph for 2 minutes. 3) Stop and idle for 30 seconds. 5) Repeat steps 3 & 4 five (5) times.

Navigation