How to replace the sway bar linkage on a Jeep Wrangler?
After the top nut is tightened, tighten the Torx bolt on the bottom of the link. Repeat these steps on the other side. If you ever add a lift to you’r vehicle these links will need to be replaced with links with longer shafts. 1 Person Made This Project!
Do you need to disconnect sway bar end links?
Disconnect end links make the job quick and easy, and usually don’t require any tools. By un-hooking the sway bar links, you’re Jeep will be free to allow the suspension to flex helping you maintain traction.
Where to put ball joint splitter on Jeep Wrangler?
This is where the ball-joint splitter comes in, you’re going to need to wedge it in between the ball joint and the bottom of the sway bar. If you don’t do this, the top nut will just turn the ball joint freely and you’ll never get it tightened.
When to replace sway bar links on 2003 Jeep Wrangler TJ?
This how-to is for replacing the sway-bar linkage on a 2003 Jeep Wrangler TJ. If you do alot of off-roading the ball-joint connectors on your sway-bar links will eventually wear out and break. While this would help your traction on uneven terrain, it is a disaster waiting to happen if you drive your Jeep on the highways.
Which is the best sway bar for a jeep?
If you plan on lifting your Jeep, the correct length of sway bar links will put the sway bar slightly raised past a flat level. About two degrees higher than a flat plane. This ensures the best performance on the road for both an electronic and manual disconnection system.
Disconnect end links make the job quick and easy, and usually don’t require any tools. By un-hooking the sway bar links, you’re Jeep will be free to allow the suspension to flex helping you maintain traction.
What does articulation mean on a jeep sway bar?
When talking about off-roading, articulation is how much flex you have. This means if one of your front wheels drives over something, you see how high up you can get that wheel without lifting another wheel off the ground. The easiest way to boost your articulation is to disconnect your front sway bar links.
How can I remove a bad sway bar link?
Identify the bad link. A bad link: Remove the nut holding the sway bar link to the sway bar. You will have to grip the shaft below the sway bar so it does not turn – for example pair of vice grip locking pliers.The bottom bolt you can use a socket wrench on the nut, and a wrench on the nut on the other side of the mounting point (see picture).
What are the links on a sway bar?
Be sure it is installed the same as the original – the bushings are touching the sway bar – from the top: nut, metal washer, bushing, sway bar, bushing, metal washer. The lower link is simply nut, mounting point, smaller nut.
How do you replace a bushing on a front sway bar?
Slide a bushing and cup pair up the bolt with the bushing’s lip toward the bar. Slide the spacer onto the bolt. Place a bushing, and then a cup, on the lower control arm where the link goes through it and slide the bolt through it. The lip on the bushing faces the lower control arm.
After the top nut is tightened, tighten the Torx bolt on the bottom of the link. Repeat these steps on the other side. If you ever add a lift to you’r vehicle these links will need to be replaced with links with longer shafts. 1 Person Made This Project!
How do you remove links from front sway bar?
To make removal of the links easier, cut them in the middle of the link with a grinding wheel, often called a “whizzer wheel”. If you don’t have one, use a wrench on the bolt head on top of the control arm and a socket and ratchet on the nut under the control arm.
What do I need to remove front wheel drive sway bar?
Remove the nuts holding the sway bar link to the bar and control arm. Remove the link. Link removal on some front-wheel-drive cars will require a ¼-inch Allen wrench to keep the bolt from spinning.
How are sway bar bushings and links changed?
Sway bar end links have undergone a design change as front suspension design has transformed. The switch to MacPherson struts required a change in how and where sway bar end links were connected. Confusing the matter even more, they connect upward to the MacPherson strut and are longer, or they connect to the lower control arm and are shorter.
When to replace sway bar links-testing autos?
An extremely worn out sway bar link can separate. This will cause your car to lean excessively in turns and feel less stable and secure on the road. A worn out sway bar link must be replaced to keep your vehicle safe. In a pickup truck, sway bar links have a slightly different design, see the lower photo.
How much does it cost to replace a sway bar?
There is no need to replace a sway bar link if it’s working properly and is not worn out. Replacing a sway bar link is not very expensive. Typically, it costs $75-$140 per side in a repair shop. If you want to replace the sway bar link yourself, soak the thread with oil or WD-40,…
What does a broken sway bar link sound like?
Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. Hello my friend and welcome to Make Fix Inspire.
An extremely worn out sway bar link can separate. This will cause your car to lean excessively in turns and feel less stable and secure on the road. A worn out sway bar link must be replaced to keep your vehicle safe. In a pickup truck, sway bar links have a slightly different design, see the lower photo.
How to replace front sway bar bushing and links?
This shows the new passenger side frame bushing on a 2001 GMC Jimmy. Lightly grease the bar, bushings, and mounts. Slide the bushing over the bar and cover it with the mount. Position and reattach the mount. Torque the nuts/bolts to specification. Grease as required.