How to buy a Jeep Cherokee ignition lock cylinder?

Shop AutoZone for Jeep Cherokee Ignition Lock Cylinder. 10% OFF $75. Use Code: DIYSAVE10 Online Ship-to-Home Orders Only If you count on your Jeep Cherokee to be able to get your kids back and forth from their daily activities, the ignition lock cylinder must be in good condition.

What kind of door lock does a Jeep Cherokee have?

Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37″ Toyo MTs. I will assume you have a 4 door Cherokee.

What’s the problem with my 1998 Jeep Cherokee?

1998 jeep Cherokee classic has door locking/unlocking problem. sometimes they work and sometimes they don’t. passenger door lock makes a ticking noise when I push the door lock on drivers door. nothing will lock or unlock electronically. any help on how to fix would be very helpful. oldman44oldjeep98, May 1, 2018.

When do you need a new ignition lock cylinder?

Use the form above to tell us what you drive. You should be able to notice when your Jeep Cherokee ignition lock cylinder wears down when you’re unable to consistently turn it in order to start the vehicle. If your keys begin to feel a bit loose once you put them in the ignition slot, you need a new key and cylinder.

Why is my passenger door lock not working?

If the passenger door button doesn’t work you will have to dig deeper and figure out where the problem is like 2oldjeeps says. The switch is the most common problem though. The door lock circuit is actually in the passenger door. I have an issue with my 00 XJ where they will work only occasionally and I can hear one of the relays clicking.

How to get full access to my Jeep Cherokee?

To get full-access, you need to register for a FREE account . Discussion in ‘ Electrical ‘ started by oldman44oldjeep98, May 1, 2018 .

When do you replace the ignition switch on a jeep?

Jeep Ignition Switch & Lock Cylinder Replacement Instructions Jeep Ignition Switch & Lock Cylinder Replacement Instructions This design was used on many Chrysler, Dodge and Jeep vehicles from the mid 1980’s through 1995. The vehicle used in this example is a 1990 Chrysler LeBaron.

When did the lock cylinder break on a jeep?

This design was used on many Chrysler, Dodge and Jeep vehicles from the mid 1980’s through 1995. The vehicle used in this example is a 1990 Chrysler LeBaron. The lock cylinders often break, stopping the key from turning enough to start the car.

How do you change ignition switch on Jeep Cherokee?

Position your replacement ignition switch at the edge of your steering column so it is prepared to install. Change the switch’s slider so that it is set on “Accessory.” Attach the slider hole and actuating rod. Connect the switch. Use your fingers to get the pair of retaining screws tight but not stuck.

Where can I get a key for my Jeep Cherokee?

We can help you with that. Tow the car to the dealer. Order a key online and have the dealer or locksmith cut and program it for you (if necessary). A word of caution: The type of key you need depends on the year and model of your Jeep Cherokee.

What are the non transponder keys for a Jeep Cherokee?

Jeep Cherokee Non-transponder keys are metal keys that have no chip in them and therefore no programming is needed: P1795/Y159, P1794/Y157, P1793/Y155, P1789/Y154, P1098J/B46, 1970AM/RA4, S1970AM/RA3.

Is there a problem with the ignition on a Jeep Cherokee?

If there is one common denominator amongst practically all 1984 to 1996 Jeep Cherokees (XJ , ZJ, WJ and WK’s alike) it is a bad ignition. Though typically robust, most Jeep Cherokees will eventually experience ignition failure, leaving otherwise happy owners stranded.

Navigation