Where is the airbag light on a Jeep Wrangler?
NOTE: THE XJ INSTRUMENT PANEL CONTAINS ONE MORE CIRCUIT IN THIS CONNECTOR THAN THE TJ. CUT THE UNUSED WIRE CLOSE TO THE CONNECTOR ON TJ MODELS. Stagger cut the main harness and patch harness wires so that the solder joints will be 1/2 inch apart. Remove 1/2 inch of insulation from the wires. The new harness will have a dark blue with no tracer.
Is there a way to reset the airbag light?
The airbag light will often go away by itself after repairing the problem, but not in all car models. After you have installed the new parts and are 100% sure that the parts are installed correctly, it’s time to reset the engine light. To do this – you need to use an OBD2 scanner, and it’s not possible in another way.
What does the air bag warning light mean?
Some vehicles may exhibit an intermittent illumination of the air bag warning light or an intermittent tachometer or speedometer drop out. An Airbag Electronic Control Module (AECM) fault code -“No Cluster CCD BUS ” message will be present.
When does the airbag light turn on without a scanner?
Some cars have a “passenger seat Airbag on/off button.” This is the first airbag light you should check when you want to remove the airbag light without a scanner. If the light is functioning well, it should turn on when someone occupies the passenger seat.
Why does the airbag light come on on a Jeep Wrangler?
Jeep Wrangler Airbag Light on Causes Your airbag light is part of your Wrangler’s larger supplemental restraint system. It works in tandem with the system to protect you in the event of an accident. If all parts of this system are not working properly, it can cause the airbag light to come on.
How to reset an airbag light you it still runs?
Start the engine. The SRS light should come on for seven seconds, and then shut off and stay off. The airbag light has been reset. If you continue to drive your vehicle with the SRS light illuminated, you may risk an accidental deployment of the airbag. “How To Use Automotive Diagnostic Scanners (Motorbooks Workshop)”; Martin; 2008
How to fix your airbag SRS warning light?
A no cost easy way to reset and fix your airbag SRS warning light. Tsukasa Azuma is an awesome car blogger of Car From Japan. He owns a car repair shop at downtown Osaka, and he put all that experience to good use in his sharing posts.
When does the airbag light come on in a car?
The airbag light, also known as the SRS light (supplemental restraint system), illuminates on the vehicle’s instrument panel usually only after the vehicle has been in an accident and the airbag has deployed.
How do you reset an airbag light in a car?
Turn the ignition off a second after the airbag light has turned off. Turn the ignition switch of your car back off for a little longer than three seconds. Repeat steps 1 through 3 twice to make three times total. Turn your ignition switch back on to fully reset the airbag light.
What happens if you leave the airbag light on?
Doing this will cause your airbag light to flash, and it can be distracting if you leave it on as it is. Luckily, you can reset and turn off your airbag light. You can also recheck the connectors in case the light fails to turn off.
Why does my airbag light flash when I Turn on the radio?
You may have made the mistake of turning on the key while installing your car radio without plugging in car airbag components. Doing this will cause your airbag light to flash, and it can be distracting if you leave it on as it is. Luckily, you can reset and turn off your airbag light.
Turn the ignition off a second after the airbag light has turned off. Turn the ignition switch of your car back off for a little longer than three seconds. Repeat steps 1 through 3 twice to make three times total. Turn your ignition switch back on to fully reset the airbag light.
NOTE: THE XJ INSTRUMENT PANEL CONTAINS ONE MORE CIRCUIT IN THIS CONNECTOR THAN THE TJ. CUT THE UNUSED WIRE CLOSE TO THE CONNECTOR ON TJ MODELS. Stagger cut the main harness and patch harness wires so that the solder joints will be 1/2 inch apart. Remove 1/2 inch of insulation from the wires. The new harness will have a dark blue with no tracer.
How long does it take for airbag light to turn off?
Repeat steps 1 through 3 twice to make three times total. Turn your ignition switch back on to fully reset the airbag light. Once you start your car, your airbag light should turn on for around seven seconds before finally turning off.
How do you replace an airbag light without a scanner?
Replacement with a new one is one way you can remove the airbag light without a scanner. Next, loosen the steering nuts using a breaker bar. This ensures that you do not remove the steering wheel completely. Pull it back and forth because the steering wheel could be strongly attached to the steering shaft.
Some vehicles may exhibit an intermittent illumination of the air bag warning light or an intermittent tachometer or speedometer drop out. An Airbag Electronic Control Module (AECM) fault code -“No Cluster CCD BUS ” message will be present.
What to do if your airbag light is not working?
THIS TECHNICAL SERVICE BULLETIN WILL NOT ADDRESS FUEL OR OIL PRESSURE GAUGE ISSUES. Disconnect the negative battery cable. Remove the instrument cluster using the procedures outlined in the appropriate servicemanual. Inspect the male terminals of pins 1 & 2 on the instrument cluster connector labeled CNB.
What kind of light does a Jeep Wrangler harness have?
The new harness will have a dark blue with no tracer. This will mate with a dark blue wire with a green tracer on TJ and with a dark blue wire with a white tracer on XJ.