Why is my Chevelle 350 hard to start?
Fuel pump check valve doesn’t maintain pressure in the fuel rail so it boils and then you have to crank excessively to get rid of the vapor before it will start. Bought a 1972 Chevelle 350 a couple years ago. Every time I drove it it wouldn’t restart easily or sometimes not at all unless I waited a while.
Why is my car so hard to start?
It could also be the battery in the car. There are many reasons for this and the answer really is based on what you mean by hard start.
Can a lack of spark timing cause an engine to run rough?
Lack of proper spark timing can cause a different problem: one or more of the cylinders may misfire. That is to say combustion may be disrupted. You will feel, and maybe hear, this as a brief stutter in the engine. You might feel that the engine runs rough or vibrates at idle, say, when you’re sitting at a red light.
What kind of gas does a 1997 Chevy truck use?
1997 chevy c1500 WT with 4.3 . getting harder to re crank.. Only driveable with both stop revving to keep it going. And that still doesnt work well. Work ive done. New cap and rotor. Cleaned…. Exh gas.
Fuel pump check valve doesn’t maintain pressure in the fuel rail so it boils and then you have to crank excessively to get rid of the vapor before it will start. Bought a 1972 Chevelle 350 a couple years ago. Every time I drove it it wouldn’t restart easily or sometimes not at all unless I waited a while.
Why does my car have a hard time starting?
As you know, a liquid cannot flow quickly if it is condensed. In that case, the engine has to push around a lot to spin and start because not much oil can get into the fuel line and the engine. You will need to change the oil filter regularly too if you do not want your car has a hard time starting.
Why is my Toyota Tacoma hard to start?
Q3: “ Toyota Tacoma starting problems – It’s incredibly hard to start when the outside air is hot.” A: For the hot start, hold the gas pedal to the floor while you turn the key to see if that does anything. If it helps then you may have a leaking fuel pressure regulator or fuel injector sending fuel into the intake on hot shut down.
Why is my Honda Fit hard to start?
Q4: “ Honda Fit starting problems – Today, i put the key in and it wouldn’t turn…took 35 minutes of trying (tried both keys i had for the car) before i could start it. had this happen a couple of times before but usually got it in three or four tries. i was ready to have the thing towed back to the dealership…any thoughts?”
Why does it take so long to start a 300K engine?
Sure why not. On high mileage engines (200k to 300k) the pistons ring can wear causing low compression which increases crank time and causes hard starting. This is because the compression ratio is low and it takes time for the engine to gain enough speed cranking by the starter to ignite the fuel air mixture.
What causes engine crank time to be extended?
Another common reason for extended crank time for engines is a vacuum leak. Engine vacuum must be a sealed system which the mass air flow and map sensors depend on to send feedback information to the main computer which in turn sets the stage for the engine starting sequence.
What causes a car to have a hard start?
This guide will help by starting with simple fixes and conclude with the more difficult. What goes wrong? Normal wear and usage can cause a hard start condition due to lack of fuel pressure, poor intake air management, false readings to the car’s computer or weak spark.
Why do I have a slow starter cranking?
Guess the cables ability to take current degrades over time with the intense heat in that area. ha ha , i know , id lived with it since may.. but it hadnt let me down , just always sounded like it might do ! Guess the cables ability to take current degrades over time with the intense heat in that area.
What should fuel pressure be on long crank?
NO MISFIRES AT PRESENT TIME TEST FUEL PRESSURE ON LONG CRANK. LET IT SIT FOR A LONG PERIOD OF TIME FUEL PRESSURE WOULD BOTTOM OUT AT 5 PSI AND TAKE AWHILE TO COME BACK UP. ONCE IT 5 PSI IT STARTD. RETURNLESS SYSTEM. FU 0 J REMOVE FUEL TANK AND DRAIN.
What to do when transmission slips after engine warms up?
If the tranny is just starting to slip then you could install a transmission cooler and this may preserve the life that is left in the tranny. As you were told it slips when the fluid gets hot, once because it gets thinner. By lowering the temp 20 to 50 degrees this can help. You can’t post conmments that contain an email address.
What causes engine hesitation on a Dodge truck?
The engine hesitation on your Dodge may be created by problems in one or more components. In most cases, a bad throttle position sensor (TPS) fails to signal the engine computer about throttle operation. Other causes may be bad or worn out components in the ignition secondary system, causing the engine to accelerate poorly and even stall.
When does a truck stall when it gets warm?
Q: Hesitation/stalling when engine gets warm. Hesitation/stalling when engine gets warm, Usually first it hesitates but it tents to take about an hour of driving before it starts hesitating. Once it starts it will not stop anytime the truck needs more power to go up a hill or to pick up speed.
What to do when a hot engine is hard to start?
Although usually engines exposed to cold weather is the most known problem related to car starting difficulties, hot engines might bring obstacles as well. Many people realize that the car does not start as easily as it should when the engine is hot and do not know what to do about it.
What do you call the cold start valve?
The cold start injector, also referred to as the cold start valve, is an engine management component found on many road going vehicles.
Why is my cold start valve leaking so much?
He said its my cold start valve and that alot of 22re engines have this problem. He told me that the valve would get weak over time and start to leak constantly because even when you shut the engine off you still have 40psi of fuel pressure in the lines. That combined with a leaking valve = starting problems and flooding out.