Are there any problems with the ignition switch on a Jeep Commander?
There is a safety recall for the ignition switch, and I feel this problem may be related to that issue. Tl-the contact owns a 2008 Jeep Commander. The contact stated that while stationary, the ignition key became stuck in the vehicle. In addition, the air bag light, the abs brake light and the traction control light illuminated as well.
Is there a recall on the Jeep Commander?
Brought the Jeep Commander to the Jeep dealership and they replaced the ignition switch as part of a recall. This did not resolve the problem at all and the dealership was unable to figure out causes for random stalling even when the Commander failed during testing with technicians.
What are the symptoms of an ignition switch failure?
The initial symptom was a slow starter. Occasionally, when I turned the key, the starter wouldn’t engage. Turning the key again would fix this problem. In the past few days, however, more serious symptoms have appeared. When I turn the key, the car will turn over fine, but the electronics will be in accessory mode.
What happens if you have an incorrect ignition code?
The chip in the key transmits a specific code, of which there are millions. If this code matches the ones programmed into the vehicle, engine starting is enabled. An incorrect key code, such as from an unprogrammed key or damaged key, would prevent engine starting. Code “confusion,” such as having multiple keys can also occur, preventing ignition.
There is a safety recall for the ignition switch, and I feel this problem may be related to that issue. Tl-the contact owns a 2008 Jeep Commander. The contact stated that while stationary, the ignition key became stuck in the vehicle. In addition, the air bag light, the abs brake light and the traction control light illuminated as well.
What was the problem with my 2008 Jeep Commander?
The contact owns a 2008 Jeep Commander. The contact stated that while driving at an unknown speed, the air bag warning light illuminated and the headlights malfunctioned. Also, the contact mentioned that the ignition switch seized on the accessory position.
Brought the Jeep Commander to the Jeep dealership and they replaced the ignition switch as part of a recall. This did not resolve the problem at all and the dealership was unable to figure out causes for random stalling even when the Commander failed during testing with technicians.
What happens when the a / C goes on on a Jeep Commander?
The rear assist lights come on, the auto high beam/low beam changes on the computer, the air bag light comes on & chimes. If the A/C is on, it goes from face to feet & back up.
Why does my Jeep not start when I Turn on the ignition?
If your vehicle does not have a check engine light this may not be a problem. It is possible that this is just the sound that the vehicle makes normally. If you’ve owns the vehicle for quite some time and… Engine heat can degrade components such as ignition coils and the crankshaft position sensor. The components will then fail once they are hot.
What’s the problem with my 2007 Jeep Commander?
Our 2007 Jeep Commander has had a recurring issue for over a year while in operation whether in motion or stationary, vehicle will shut off randomly. When you attempt to restart the vehicle, it starts right back up again. The random vehicle shutdowns take place in all driving conditions and regardless of uphill or downhill driving.
What happens when there is no power in a jeep?
If there is no power, then the electrical circuit supplying the motor has a fault. That circuit begins at the battery and includes grounds, wiring (some of which is very heavy cabling), fuses, relays, the ignition switch and terminations.
What to do if your ignition switch fails?
This recall involved replacing the ignition switch and lock cylinder with stiffer components to prevent the key from turning to the off position while driving. Now, unfortunately, the ignition switch appears to be failing. The initial symptom was a slow starter. Occasionally, when I turned the key, the starter wouldn’t engage.
What is the code on the ignition switch?
Pulling the code reveal a u1403 and u1411 code. When bumps are hit or the ac is on the lights flash and sometime wiggling the ignition switch stops the flashing other times it is random and sometime more sporadic, when the vehicle is experiencing the problem the car ignition can be shut off and the restarted sometimes it stops the trouble. .
The vehicle was towed by a independent towing company to a independent mechanic were it was diagnosed with the ignition switch and gear shifter needed to be replaced. The ignition switch was replaced however, the gear shifter was not. The failure recurred.
Pulling the code reveal a u1403 and u1411 code. When bumps are hit or the ac is on the lights flash and sometime wiggling the ignition switch stops the flashing other times it is random and sometime more sporadic, when the vehicle is experiencing the problem the car ignition can be shut off and the restarted sometimes it stops the trouble. .
What causes a bad ignition switch on a Jeep Commander?
Your symptoms could be a bad ignition switch or it could be this common problem as well. The earlier Commanders had a common problem with the terminals on the starter motor, where the cables/wires connected.
Is there a recall on the ignition switch?
The ignition switch recall P41 just replaced the mechanical parts of the switch, not the switch itself or the lock/key on the 06. The ignition switch recall P41 just replaced the mechanical parts of the switch, not the switch itself or the lock/key on the 06.
What causes the ignition switch to back out?
Your symptoms could also be caused by a loose wire in the harness connector at the ignition switch. Sometimes when reconnecting the harness, one of the terminals in the connector will “back out” and make intermittent connection with the pins on the back of the switch.