What kind of axles does a Jeep Wrangler use?
The Three Wrangler Dana Axles. The Dana portion is the nameplate of Dana Inc., who is the manufacturer of the Jeep axles. There have been a few different axles used in Wranglers over the years with the Dana 44 being the most popular.
What kind of drive does a Jeep Wrangler have?
The system is better utilized during high on-road speeds. Jeeps use a 4WD (four-wheel drive) system which is an older and more mechanical drivetrain. Normally Jeeps are rear wheel drive trucks. The driver can manually engage the transfer case to engage the front differential. The power is delivered to opposed wheels.
How do you change the differential on a jeep?
Give your Jeep’s differential cover a couple of good whacks with a deadblow hammer to break it free from the RTV seal still holding it onto your Jeep’s axle. Once it breaks free, the top bolt you left on will keep the cover from falling while the gear oil drains into the oil catch pan. 4b.
What to do when your Jeep differential droops?
This will cause your axle to droop allowing you easier access to the upper differential cover bolts. 2a. If you are servicing a Dana 30 or Dana 44 differential on your Jeep, place place an oil catch pan underneath the differential and then use the square head of a 3/8″ drive ratchet to remove the fill plug on your differential cover.
When to do front end alignment on Jeep Wrangler?
If you have made the decision to install a suspension lift or change out other steering components on your Jeep TJ Wrangler, it is certainly important to get a proper front end alignment after installing these products. Not just for safety and handling issues, but also because an improperly aligned front can result in severe tire wear.
What does death wobble mean on a Jeep Wrangler?
Death wobble is a rapid oscillation in your steering components and results in your steering wheel moving very quickly from side to side. It has earned this name because it feels like your Wrangler is literally falling apart and that letting go of the steering wheel can lead to a very bad day.
When do you need to replace the tie rod on a jeep?
To check these, use a jack to lift up the front of the Jeep and then have a friend grab one wheel and twist it back and forth. If the tie rod doesn’t move, but the ends seem to wiggle, then they most likely need replacement. Of course, if the rubber boot is torn or damaged that is another replacement sign.
What to do when your Jeep suspension breaks?
Fixing it requires finding which part of the Jeep suspension puzzle is the catalyst. The first step is to check your suspension components for wear or damage. Most likely it will be the front track bar, tie-rod ends, or the ball joints. After replacing any suspension piece, get your rig’s alignment checked.
The Three Wrangler Dana Axles. The Dana portion is the nameplate of Dana Inc., who is the manufacturer of the Jeep axles. There have been a few different axles used in Wranglers over the years with the Dana 44 being the most popular.
How are axles measured on a Wrangler model 44?
The non-Rubicon model 44s are the same length. Axle shafts with a u-joint in the center are measured from the center of the u-joint. Measuring front the center to the end of the shaft will get you the inner and outer axle lengths. C-clip axle shafts and semi-float axle shafts are measured slightly differently than the full-float shafts.
What’s the difference between the Dana axles and axles?
The Dana 30 is once again at the front, but all Rubicon JKs will have Dana 44s in the front and rear. JL Wranglers have a Dana 30 up front and a Dana 35 in the rear. The exception as always is the Rubicon (44s front and back). What’s the Difference Between the Dana Axles?
What causes Jeep Wrangler 4 wheel drive to not engage?
Jeep 4 Wheel Drive not engaging 1 Failed Actuator. The actuator is a component found mostly on modern four-wheel drives and is designed to electronically engage 4 wheel drive. 2 Vacuum Hose Damage. 3 Vacuum Hoses Unhooked or ripped off. 4 Faulty Vacuum Switch.
What to consider when handling a Jeep Wrangler?
Other thing to consider when handling is concerned is your tire pressure. Make sure to run all 4 tires at the specified tire pressure, as running low pressure in your tires will affect your Jeeps handling in a negative manner.
What’s the difference between YJ and Dana 30 axles?
The Dana 30 gear ratios are either 3.21 or 3.73. The width of the axle shafts is 1.13 inches. The YJ Dana 30 hold a reverse cut ring and pinion, but the TJs do not. Both TJs and YJs, however, use a 5×4.5 inch bolt pattern.
What kind of engine does a 1989 Jeep Wrangler have?
The 1989 Jeep Wrangler keeps to the previous year tradition of having two engines available: a 4.2 liter 6 cylinder and a 2.5 liter I4. Also like the previous year models, the 1989 Jeep Wrangler has two available transmissions, a 3 speed automatic and a 5 speed manual.
What kind of sunroof does a 1989 Jeep Wrangler have?
But don’t worry, the 1989 Jeep Wrangler has something better than a sunroof; it’s got a removable soft top available, which isn’t too difficult to take off and put on. Owners of the 1989 Jeep Wrangler typically had good things to say, especially since most of the posts online are about the SUV after it was 10 years old.
Is there air conditioning in a 1989 Jeep Wrangler?
Air conditioning is optional, as is a cassette player. But don’t worry, the 1989 Jeep Wrangler has something better than a sunroof; it’s got a removable soft top available, which isn’t too difficult to take off and put on.
How many seats does a 1989 Jeep Wrangler have?
The 1989 Jeep Wrangler featured air conditioning and a tape deck as options. The vehicle has two doors and seats up to four people. There are no Jeep Wranglers with amenities such as power locks, seats or windows.
The non-Rubicon model 44s are the same length. Axle shafts with a u-joint in the center are measured from the center of the u-joint. Measuring front the center to the end of the shaft will get you the inner and outer axle lengths. C-clip axle shafts and semi-float axle shafts are measured slightly differently than the full-float shafts.
How are axle lengths measured on a wrangler?
Measuring front the center to the end of the shaft will get you the inner and outer axle lengths. C-clip axle shafts and semi-float axle shafts are measured slightly differently than the full-float shafts. C-clip and semi-floats are measured from the end of the splines to the front of the mounting flange.
What’s the gear ratio on a Wrangler Rubicon?
Rubicon models come standard with a 4.10 rear gear ratio and also use a Dana 44 axle in the front with either a 3.73 or 4.10 gear ratio. Rubicon models also come with an electronically lockable differential for optimal traction while in 4WD.
When do you need to replace the front axle on a Jeep Grand Cherokee?
The axle has two joints, called CV joints, that flex and allow the axle mobility when turning and going over bumps in the road. When the axle fails, it is usually because of CV joint failure. This often presents itself as a clicking or grinding noise when you make turns. When this happens, you must replace your Grand Cherokee’s front axle.
How much does it cost to replace rear axle seals?
When I replaced both axle seals I took both rear axles to the shop (just as they came out of the housing) and they removed and replaced the collars, bearings, seals, and plates for $30/axle. I used an angle grinder (carefully) and a chisel.