Why does my YJ Wrangler not start up?

A common problem with YJ Wranglers – turn the key and it doesnt start or it takes a few minuted to fire up Sometimes called “Lazy PCM”. Some simple tips and a certain way to tell if it is you ECM going south.

What to do if your Jeep Wrangler battery won’t start?

The first starting point when diagnosing a dead battery is to verify your battery has the correct voltage. Incorrect or low power to the starter will not start your Jeep. Batteries use CCA (Cold Cranking Amps) to measure starting power.

What to do if your Jeep Wrangler wont turn over?

OWNER NOTIFICATION BEGAN APRIL 8, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403. To diagnose, you first need to determine if the problem is electrical or fuel related.

Why does my Jeep Wrangler not have fuel pressure?

Problem: Jeep would run for a day then die and not get any fuel pressure or would run for a few weeks and then fail to start with no fuel pressure. Temporary solution was to unplug the grey plug next to the ecu and plug it back in, this would solve the problem for a short time. Also note be sure your battery is sitting on the black temp sensor.

What does it mean when your Jeep won’t start?

My jeep won’t start. It will turn over, but won’t fire. The gauges and lights all come on, but show nothing. Shows I’m on empty, which I know there is a half tank.

Why does my Jeep turn over but wont fire?

Either you have a bad key, bad antenna ring in the column, a bad SKIM module, or bad wiring somewhere in between these components. The Jeep will start then stall a few times, then the PCM will be forced to go into “sleep” mode until the problem is fixed.

Why are there no parking lights on my 92 Cherokee?

92 cherokee limited No Parking Lamps,Dash,lights! Well this started after the battery went dead. First the head lamp flashed after installing new battery. reset security with key lock and unlock drivers and passenger door. Head lamps stopped flashing after locking and unlocking passenger door.

What to do if your Jeep Wrangler won’t start?

Troubleshooting Jeep TJ Wrangler! Won’t Start but Problem Found – Project 2004 If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

What kind of Jeep Wrangler wont turn over?

Enter your ride HERE to be a part of MAY’s Ride of the Month Challenge! I have a 92 wrangler 4.0 6cyl with 5 speed, 200,000 miles on it and it just died. I have no electrical, wont turn over, no lights.

Where is the starter relay on a Jeep Wrangler?

There is a small “Starter Relay” inside that should cllick softly when you turn the ignition key to Start. That Starter Relay in turn energizes the big starter relay located on the starter motor where the engine bolts to the transmission, underneath.

What kind of battery does a Jeep Wrangler have?

I have a 92 wrangler 4.0 6cyl with 5 speed, 200,000 miles on it and it just died. I have no electrical, wont turn over, no lights. If I put on the hazard I can hear the relay click but no lights. The parking brake light on the dash lights up but VERY faint. -New battery…nothing, still worn turn over, no power.

Is there a 2.5 engine in a Jeep Wrangler?

They are severely underpowered for the weight of the jeep. The 4.0 gets almost as good of milage and has the power to actually pass someone if need be. Also a 2.5 engine is hard to find and expensive….4.0’s are plentiful and half the price. I just bought a 4.0 TJ just to get away from the 2.5 nightmare. Mine has 143K and I hate it.

How to take ECU out of Jeep Wrangler?

1. take ECU out of Jeep you’ll need to remove the washer fluid container held on by one philips screw on the side and then it just slides right out. 2.now for taking off the ECU disconnect the main wiring harness leading into it using a 8mm socket, when loosen bolt and pull off gently being sure not so break any contacts.

When to replace ignition switch on Jeep Wrangler?

DEALERS WILL REPLACE THE IGNITION SWITCH WITH A REDESIGNED SWITCH. OWNER NOTIFICATION BEGAN APRIL 8, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.

What causes a jeep to have a no start condition?

The usual suspects, that can cause this type of problem, are a bad fuel pump, bad crank sensor, bad ignition coil (if your Jeep is distributor equipped), etc. Does Not Crank Condition: Means that the engine is not cranking when you turn the key to crank the engine.

What does it mean when your Honda Civic won’t start?

Does Not Crank Condition: Means that the engine is not cranking when you turn the key to crank the engine. In other words, the engine doesn’t turn over at all. This is usually due to a bad starter motor, bad ignition switch, bad neutral safety switch, or the engine is locked up.

Why does my Jeep Wrangler have no cel?

The whole reason for that is a) symptom number 1; no CEL means no codes either while the problem is on going, and b) even after you get the jeep started, the computer only sees this as a normal start once it gets power, as if you had just turned the key on right then instead of 10 minutes ago.

Is there a code for a Jeep Wrangler YJ 1991?

It doesn’t realize there’s a problem so there’s no code stored. Bottom line is, if you don’t have these symptoms (the clicking noise is the ONLY one that is optional) or are dealing with a pre 91 vehicle, then what follows isn’t going to apply to you.

What causes a car to have no start?

The components that are responsible for drawing in the air the engine needs are the: engine pistons, cylinder head valves, and all the other related components like: timing chain, etc. Although rare, internal engine mechanical problems can and do cause no start conditions.

Why does my Jeep turn over but does not start?

Cranks But Does Not Start Condition: In this type of condition, you turn the key and the engine in your Jeep cranks (turns over) but it doesn’t start (run). The usual suspects, that can cause this type of problem, are a bad fuel pump, bad crank sensor, bad ignition coil (if your Jeep is distributor equipped), etc.

When does a Jeep Wrangler Unlimited not start?

2 months after I leased a new 2018 JK unlimited with 800+ miles I stopped to get gas and it wouldn’t start, but in 15 minutes or so it magically started. A couple of months later it happened again.

How to troubleshoot a no start Jeep 4.0L?

More specifically, this means that troubleshooting the problem requires that you check and confirm that: All 6 cylinders are getting spark (with a spark tester). That the fuel pump is creating enough fuel pressure. And if necessary, check the engine’s health with a compression test. I’ll go into more specific details in the following headings: 1.)

What is the ignition system on a jeep?

The ignition system is the one tasked with creating and delivering spark to each of the 6 cylinders. Without spark, the engine will crank but Not Start. The ignition system of the Jeep vehicles covered by this tutorial use either a distributor type system or a COP (Coil-on-Plug) ignition coil system.

Why does my Jeep not start when I Turn on the ignition?

If your vehicle does not have a check engine light this may not be a problem. It is possible that this is just the sound that the vehicle makes normally. If you’ve owns the vehicle for quite some time and… Engine heat can degrade components such as ignition coils and the crankshaft position sensor. The components will then fail once they are hot.

How to reset your Jeep engine control module?

3- Once the time has passed you should now turn the headlights “on” and “off” twice to drain the Engine Control Module from any remaining power. 4- Now plug back in the negative terminal and your Jeep ECM should now be reset. To finish off this post , here are a couple of things you should keep in mind.

What happens when there is no power in a jeep?

If there is no power, then the electrical circuit supplying the motor has a fault. That circuit begins at the battery and includes grounds, wiring (some of which is very heavy cabling), fuses, relays, the ignition switch and terminations.

How to test 12V power on Jeep Wrangler YJ?

Just remember to hook it back up when it comes time to test for 12V power again or you’ll be scratching your head. To actually do the test, set your dial to Ohms/resistance/continuity and simply touch one lead from the meter to your starting point, and the other to your ending power and watch you meter for whatever it does when there is continuity.

Why does my Jeep Wrangler YJ make clicking noise?

Bottom line is, if you don’t have these symptoms (the clicking noise is the ONLY one that is optional) or are dealing with a pre 91 vehicle, then what follows isn’t going to apply to you. Sorry but you have other issues that I’m not covering here, like faulty fuel pumps, bad coils, burnt fusible links and whole slew of other possible choices.

What should the battery reading be on a Jeep Wrangler?

Batteries use CCA (Cold Cranking Amps) to measure starting power. Be aware that your battery could have power, however, when under load, the cranking amps are not powerful enough to get the starter to crank the engine. A good fully charged battery should read over 12.6 volts. If the battery reads 12.45 volts or less, it is low.

Is the Jeep Grand Cherokee 4.0 with no start?

Come along with Eric O. at SMA as he has a look at this 2001 Jeep Grand Cherokee with the I6 4.0 that was towed in with a crank, no start condition. It didn’t take long to figure out this common problem and solve the infamous P0320 crank sensor code.

What causes death wobble on a Jeep Wrangler?

Worn wheel bearings may contribute to death wobble as well and are very easy to test. Jack up one of your Jeep’s front wheels and grasp the tire at the 12- and 6-o’clock position, then wiggle the tire. If you feel movement, then you most likely have a worn wheel bearing. Check the other side as well.

What causes bump steer on a Jeep Wrangler?

Bump steer occurs when the vehicle darts right or left after hitting a bump in the road, and is easier to identify through improperly installed suspension kits, or broken/damaged steering components. Nor should it be confused with a vibrations felt at higher speeds, as this is normally caused by an improperly aligned vehicle.

Is the axle going to fall off a jeep?

“It can definitely be a scary thing, death wobble, with the Jeep violently bashing and everything inside rattling, especially on the highway. It almost felt like the axle was going to fall off.” In reality, the axle won’t fall off. Nor will the wheels come apart.

What to do when your Jeep Cherokee won’t start?

The first thing to check when the engine won’t start is to see if you have spark at the spark plugs. When the car won’t start and you have a spark at the spark plugs then the problem would most likely be in the fuel system. Checking fuel pressure would be next and also checking to see if you have an injector pulse at the fuel injectors.

Why does my Jeep Cherokee have no spark?

I have no communication to the computer with a scanner, no check engine light, no 5 v reference, no spark. I have tried to manually pull codes with the key. The dealer says that it does not have an immobilizer by the VIN number. I have power and grounds to the PCM connectors.

Why does my Jeep Wrangler JK not start?

Jeep Wrangler JK Won’t Start One Click If your Jeep won’t start and you simply hear one click, then you could have a faulty starter motor. Again, using a voltmeter with a load function, make sure all your voltages are all correct.

Navigation

Why does my YJ Wrangler not start up?