Why is my Jeep stock radio not working?
Especially vehicle pcbs as they have to be “rugged”. The power caps and ICs are the likely culprits. Check the solder points underneath the pcb too (most pcbs of that era are through-hole). Look for the solder to be cracked away from the via.
What to look for in a jeep radio?
Check the solder points underneath the pcb too (most pcbs of that era are through-hole). Look for the solder to be cracked away from the via. A crack will look like a clean ring around the entire joint. The other thing to look for is blown capacitors.
What causes solder to crack on Jeep radio?
Especially vehicle pcbs as they have to be “rugged”. The power caps and ICs are the likely culprits. Check the solder points underneath the pcb too (most pcbs of that era are through-hole). Look for the solder to be cracked away from the via. A crack will look like a clean ring around the entire joint.
Why is there no sound on my Radio?
Dont have the option code because im at work right now. I can turn it on and off and change stations but there is no sound and no response from the steering wheel volume control or the radio knob. Anyone know the cure for this?
Why is the radio not working on my Jeep Wrangler?
No problem. This morning, my radio lit up, but no sound. At first, I thought that the radio station had a problem. So, I switched stations. Still no sound. No sound from the CD player, either. I checked fuse #3 (sub woofer system) & fuse #14 (radio). Both looked good.
Where can I get United radio for my Jeep Wrangler?
Here’s the United Radio www.unitedradio.com/automotive-electronics/ 5717 Enterprise Parkway East Syracuse NY 13057 1-800-634-8606 Mon-Fri 8:30 AM – 5:30 PM 39 people found this helpful. I have a Jeep JK Wrangler – same problem with the radio.
What kind of radio does a Jeep Cherokee have?
I have a 2019 Jeep Cherokee and today my radio (AM/FM) has stop working and I’m not able to use the touch screen to change my SXM channels I have to use steering wheel controls. Has anyone seen this? My radio is acting wonky as well. I have a 2016 jeep Cherokee and the phone will not connect at all.
What to do when your radio won’t turn on?
Put a test light across the power leads at the radio. If there is power, and you have a good ground, you either need a new radio or the lead isn’t making good contact t the plug. If not, check for power ar the fuse. If there is power there, the wire is bad between the fuse and the radio.
How old is the Jeep Grand Cherokee CD player?
The Jeep Grand Cherokee was redesigned for the 1999 model year; the 2000 models have minimal changes. This model is also known as Jeep WJ. From numerous forums on the web, I have discovered that the Jeep stock radio/CD players are prone to failing when they are 10+ years old.
Is it worth it to repair a jeep radio?
In the 21st century, repair men and ladies are gone to the way side, the labor prices make these small jobs not worth the effort, everybody is just replacing their units with new, used, aftermarket or trying simple repairs themselves as mentioned here, good luck.
Is there a fix for a jeep radio?
I had it in my mind that a similar repair to the Playstation 3’s yellow ring of death fix, which involves removing the motherboard and heating the circuits until the micro soldering reattaches, might work for the circuitry in these radios. Any ideas?
The Jeep Grand Cherokee was redesigned for the 1999 model year; the 2000 models have minimal changes. This model is also known as Jeep WJ. From numerous forums on the web, I have discovered that the Jeep stock radio/CD players are prone to failing when they are 10+ years old.
Especially vehicle pcbs as they have to be “rugged”. The power caps and ICs are the likely culprits. Check the solder points underneath the pcb too (most pcbs of that era are through-hole). Look for the solder to be cracked away from the via. A crack will look like a clean ring around the entire joint.
Especially vehicle pcbs as they have to be “rugged”. The power caps and ICs are the likely culprits. Check the solder points underneath the pcb too (most pcbs of that era are through-hole). Look for the solder to be cracked away from the via.
Check the solder points underneath the pcb too (most pcbs of that era are through-hole). Look for the solder to be cracked away from the via. A crack will look like a clean ring around the entire joint. The other thing to look for is blown capacitors.