How do you install a serpentine belt on a water pump?
If you have to install a serpentine belt, use the breaker bar to relax the tensioner and slide the belt onto the last pulley. If you have to install a v-belt, slide the tensioner over and tighten it. Make adjustments to the v-belt by loosening and tightening the tensioner until the belt is loose to its width or about a 1/4 inch.
When to put a new serpentine belt on a car?
A good mechanic would make sure everything is rotating freely before putting the new belt. I find it hard to believe the shop didn’t check the water pump – the serpentine belt drives the water pump, alternator, power steering pump, and A/C compressor. If the water pump is frozen, likely it would at least break/throw the serpentine belt.
How do you remove a water pump belt?
If it is a serpentine belt, remove the belt by using a serpentine belt tool and turning the tensioner to relax the belt. If the vehicle has a v-belt, loosen the tensioner to relax the belt. Step 8: Remove the belt or belts from the pulleys.
Why is my water pump belt not working?
If your vehicle continues to make noises after replacing the water pump belt, then there may be further diagnosis of the water pump belt needed or a possible belt tensioner failure. If the problem persists, have one of YourMechanic’s certified technicians take a look.
What makes a serpentine belt need to be replaced?
These include a misaligned power steering pump pulley, idler pulley (s), automatic belt tensioner pulley, water pump pulley (which may be due to wear in the pump shaft bearings), and even a worn or loose harmonic balancer.
Why is my serpentine belt on my water pump too tight?
One of the most common failure modes for water pumps is actually bearing failure, caused by a serpentine belt that was too tight. If you think your belt may be too tight, it’s best to address this issue as soon as possible to prevent expensive engine damage caused by overheating. Serpentine Belt Replacement Cost Looking for Replacement Parts?
Can a power steering pump work without a serpentine belt?
Some of the main accessories include a power steering pump, alternator, air conditioning compressor, and water pump. However, these devices cannot function properly without the help of a serpentine belt. This one long continuous belt is the force that drives many of the engine’s peripheral devices.
What did the serpentine belt break on my son’s Chevy Lumina?
The serpentine belt in my son’s 1999 Chevy Lumina broke. The repair shop replaced the belt and the tensioner. $180 repair bill. The night he got the care from the shop, the belt broke again. This time, they said the water pump froze up, broke the serpentine belt and bent the pully on the tensioner. $275 to fix it this time.
How do you change the belt on a water pump?
If you have to install a v-belt, slide the tensioner over and tighten it. Make adjustments to the v-belt by loosening and tightening the tensioner until the belt is loose to its width or about a 1/4 inch. Step 13: Pick up all tools used to change the water pump belt. Step 14: Remove the wheel chocks and put them aside.
Why do you need a water pump in your car?
Water pump are vital for the cooling system on a vehicle. With a malfunctioning cooling system, the engine overheats within minutes. There are two types of belts used to drive the engine’s water pump: the V-belt and the serpentine belt.
When to replace idler pulleys, tensioner and water pump?
Generally, the idler pulleys, tensioner and water pump should always be replaced when the timing belt is replaced. In most cases, the timing belt drives the water pump, so it is the right time to replace the water pump. It is also recommended by the manufacturer. WORD TO THE WISE.
What’s the best way to replace a water pump pulley?
If you are reinstalling a serpentine belt, use the breaker bar to relax the tensioner and slide the belt onto the last pulley. If you are reinstalling a v-belt, slide the tensioner over and tighten it. Make adjustments to the v-belt by loosening and tightening the tensioner until the belt is loose to its width or about a 1/4 inch.
If you have to install a serpentine belt, use the breaker bar to relax the tensioner and slide the belt onto the last pulley. If you have to install a v-belt, slide the tensioner over and tighten it. Make adjustments to the v-belt by loosening and tightening the tensioner until the belt is loose to its width or about a 1/4 inch.
If you have to install a v-belt, slide the tensioner over and tighten it. Make adjustments to the v-belt by loosening and tightening the tensioner until the belt is loose to its width or about a 1/4 inch. Step 13: Pick up all tools used to change the water pump belt. Step 14: Remove the wheel chocks and put them aside.