What is the p0138 code on the O2 sensor?
The P0138 code is set when the Engine Control Module (ECM) detects that the rear O2 sensor signal voltage remains excessively high for an extended period of time. The Heated Oxygen Sensor 2 (HO2S) (Rear O2 Sensor), after three-way catalyst (manifold), monitors the oxygen level in the exhaust gas on each bank.
What does OBD II fault code p0038 mean?
What Does Code P0038 Mean? OBD II fault code P0038 is defined as “Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2), and is set when the PCM (Powertrain Control Module) detects a signal voltage from oxygen sensor #2 that does not fall within the predefined range for that sensor.
What does p0138 mean on a Jeep Wrangler?
Users have reported P0138 for the following makes: Jeep (especially on a Jeep Wrangler), Dodge, Toyota, Nissan, and Chevrolet. Code P0138 means that your powertrain control module (PCM) has detected that the voltage signal from the rear O2 sensor is too high. What is an Oxygen Sensor? All modern cars have at least two oxygen sensors.
When does the O2 sensor turn on the Check Engine light?
The engine control module (ECM) sees the voltage of the O2 sensor for bank 1 sensor 2 above 1.2 volts when the ECM has commanded the fuel to a targeted lean condition on that bank of the engine. The ECM detects the voltage high problem and turns on the Check Engine Light.
What does the code p0138 mean on the O2 sensor?
What the P0138 code means. P0138 is the OBD-II generic code indicating the O2 sensor for bank 1 sensor 2 fails to have a lower voltage output below 1.2 volts for more than 10 seconds indicating a lack of oxygen in the exhaust stream.
What Does Code P0038 Mean? OBD II fault code P0038 is defined as “Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2), and is set when the PCM (Powertrain Control Module) detects a signal voltage from oxygen sensor #2 that does not fall within the predefined range for that sensor.
Users have reported P0138 for the following makes: Jeep (especially on a Jeep Wrangler), Dodge, Toyota, Nissan, and Chevrolet. Code P0138 means that your powertrain control module (PCM) has detected that the voltage signal from the rear O2 sensor is too high. What is an Oxygen Sensor? All modern cars have at least two oxygen sensors.
The engine control module (ECM) sees the voltage of the O2 sensor for bank 1 sensor 2 above 1.2 volts when the ECM has commanded the fuel to a targeted lean condition on that bank of the engine. The ECM detects the voltage high problem and turns on the Check Engine Light.
What is the code for bank 1 O2 sensor?
All our repairs are backed by our 12-month / 12,000-mile warranty. P0138 is the OBD-II generic code indicating the O2 sensor for bank 1 sensor 2 fails to have a lower voltage output below 1.2 volts for more than 10 seconds indicating a lack of oxygen in the exhaust stream.
What are the possible causes of p0138 Toyota?
P0138 TOYOTA Possible Causes Faulty Rear Heated Oxygen Sensor Bank 1 Rear Heated Oxygen Sensor Bank 1 harness is open or shorted Rear Heated Oxygen Sensor Bank 1 circuit poor electrical connection Intake air leaks Exhaust gas leaks Inappropriate fuel pressure Faulty fuel injectors What does this mean? How do I fix code P0138 TOYOTA
What does p0138 mean in a catalytic converter?
O2 Sensor Circuit High Voltage (Bank 1, Sensor 2) What Does P0138 Mean? Oxygen sensor 2 is the downstream oxygen sensor in relationship to the catalytic converter. It measures the amount of air and fuel coming out of the catalytic converter to ensure the catalytic converter is functioning properly.
What causes engine code p0138?
The P0138 code is set when the Engine Control Module (ECM) detects that the rear O2 sensor signal voltage remains excessively high for an extended period of time. Possible Symptoms Engine Light ON (or Service Engine Soon Warning Light)
Where is the bank 1 sensor 1 oxygen sensor located?
Bank one is the engine cylinder bank near the engine firewall (see diagram). The bank one sensor one is the Oxygen sensor (O2) located in the exhaust pipe just of the engine cylinder bank at rear and before the Catalytic Converters .
What does Bank 2 sensor 2 oxygen sensor do?
O2 sensors on a specific bank marked as “sensor 2” (as this one is) are used to monitor emissions. A Three-Way Catalyst (TWC) system (catalytic converter) is used to control tailpipe emissions. The PCM uses the signal received from Oxygen sensor 2 (#2 indicates aft of catalytic converter, #1 indicates pre-converter)…
Which sensor is Bank 1 sensor 1?
Bank 1 Sensor 1 is a sensor that is used by the computer (ECM) to monitor the amount of oxygen exiting the engine. The ECM uses the signal from the O2 sensor to adjust the fuel and air ratio of the engine.