Are there any problems with the ignition switch on the Jeep Grand Cherokee?

29 problems related to ignition switch have been reported for the 2008 Jeep Grand Cherokee. The most recently reported issues are listed below. Please also check out the statistics and reliability analysis of the 2008 Jeep Grand Cherokee based on all problems reported for the 2008 Grand Cherokee.

Why is my 2008 Jeep Grand Cherokee not starting?

2008 Grand Cherokee began experiencing intermittent starting problems. Without warning the vehicle would not turn over. All dash lights were working. As well as radio, AC, power windows and all other electrical systems. No codes showed on the computer.

Is there a recall on a 2008 Jeep Grand Cherokee?

The switch is already under recall. The contact owns a 2008 Jeep Grand Cherokee. While driving at various speeds, the vehicle would suddenly shut off. The vehicle was taken to the dealer where it was diagnosed that the ignition switch was faulty and needed to be replaced.

Where is the power distribution center on a Jeep Grand Cherokee?

Power Distribution Center (PDC) Relays, Final Drive Control Module (FDCM), Front Control Module (FCM) (R/S), A580 (R/S) The power distribution center located in the engine compartment near the battery. WARNING: Terminal and harness assignments for individual connectors will vary depending on vehicle equipment level, model, and market.

What kind of ignition switch does a Jeep Grand Cherokee use?

For the utmost dependability, equip your vehicle with good ignition system components — AutoZone’s your source for the Jeep Grand Cherokee ignition switch you need to restore your confidence on the road. Cherokee ignition switches are the components which route key signals to starter relays.

Where can I get 2008 Jeep Grand Cherokee parts?

Parts that perform. OEM Jeep Grand Cherokee Parts. Genuine 2008 Jeep Grand Cherokee Parts from Factory Chrysler Parts in Bartow, FL. Jeep OEM 2008 Grand Cherokee Parts from Thunder CDJR. Genuine Jeep parts are the smart choice for repair, maintenance, or upgrade of your 2008 Jeep Grand Cherokee .

What causes battery to drain in Jeep Grand Cherokee?

After turning off engine, key fob is seized in ignition switch, but releases after period of time. This is a constant recurring issue, with varying wait times, occurring each time car is driven. Prolonged wait time causes battery to drain. The contact owns a 2008 Jeep Grand Cherokee.

Are there any problems with the Jeep Grand Cherokee?

Other Common Electrical System related problems of Jeep Grand Cherokee Problem Category Number of Problems Electrical System problems 3956 Alternator/generator/regulator problems 369 Ignition Switch problems 289 Car Will Not Start problems 251

Is there a recall on the Jeep Commander?

THE RECALL BEGAN ON OCTOBER 22, 2007. OWNERS MAY CONTACT DAIMLERCHRYSLER AT 1-800-853-1403. Chrysler Group LLC (Chrysler) is recalling certain model year 2005-2010 Jeep Grand Cherokee vehicles manufactured February 11, 2004, through March 9, 2010; and 2006-2010 Jeep Commander vehicles manufactured January 31, 2005, through March 10, 2010.

What was the mileage on a 2008 Jeep Grand Cherokee?

The failure mileage was 71,000. Tl the contact owns a 2008 Jeep Grand Cherokee. While driving, the ignition switch would turn off independently and the vehicle stalled. The vehicle was restarted and was able to drive normally. There were no warning indicators illuminated.

Jeep Grand Cherokee owners have reported 286 problems related to ignition switch (under the electrical system category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Jeep Grand Cherokee based on all problems reported for the Grand Cherokee.

Why does my GM ignition key not turn?

Sometimes the ignition key won’t turn or rotate. If that happens the vehicle won’t start, the steering wheel won’t turn and it won’t shift into gear. On a late 90’s or early 2000 GM vehicle this is the way to get it apart so you can replace the tumbler. Category Autos & Vehicles.

What happens when your key won’t turn in?

If your key won’t turn your ignition lock cylinder and the steps above did not get your ignition to turn, then there is an extremely good chance your vehicle is in the list below. The list below is just a partial list of vehicles we suspect of having ignition failure problems when people call and say “My key won’t turn in my ignition”.

How can you tell if your ignition key is locked?

Check to see if your steering wheel is locked by trying to turn the wheel. If it will not move, or moves only very slightly, it is likely locked. A locked steering wheel will not allow the ignition to engage. When you move the wheel back and forth, you will feel it stop abruptly as it comes into contact with the steering wheel lock.

Why is the ignition key stuck in my Grand Cherokee?

Brilliant post, Milo, very useful. I have a 2003 Grand Cherokee Overland 2.7 CRD, which I love, and earlier today the ignition key would not come out of the ignition. My first thought was the ignition lock itself, so I spent some time jiggling the key in the lock without success.

How to remove skim key from Jeep Grand Cherokee?

JEEP SKIM KEY PROBLEM… SOLVED!!!! ECM REPROGRAMMED Jeep Grand Cherokee. Remove SKIM from ECM If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

How do you get the ignition key out of a jeep?

Access the solenoid: Lift the rubber mat off the tray and remove the two tray screws. You will see the solenoid. It’s a white cylinder with a metal bar protruding rearward toward the shifter. You might opt to remove the center console too. Quick Fix: If you’re in a jam and need to remove the key without disassembling things read on.

Why does my Jeep not start when I Turn on the ignition?

If your vehicle does not have a check engine light this may not be a problem. It is possible that this is just the sound that the vehicle makes normally. If you’ve owns the vehicle for quite some time and… Engine heat can degrade components such as ignition coils and the crankshaft position sensor. The components will then fail once they are hot.

Where can I get my Jeep Grand Cherokee repaired?

The contact took the vehicle to mac haik jackson cdjr (5395 interstate 55 north frontage rd, jackson, ms 39211) where he had the vehicle serviced and repaired for the recall. Recently, the contact stated that while either stopped or driving at various speed, the vehicle would unexpectedly shut off.

Is it dangerous to drive a Jeep Grand Cherokee at night?

Very dangerous situation to drive at night with unreliable lights. After turning off engine, key fob is seized in ignition switch, but releases after period of time. This is a constant recurring issue, with varying wait times, occurring each time car is driven. Prolonged wait time causes battery to drain.

Is there an electrical problem with my Grand Cherokee?

I have been experiencing random electrical problems. The symptom is that the all the lights and gauges on the dash cluster go on and off erratically and sometimes stay off for a few minutes. This also includes the A/C system. As the gauges go off so does the A/C fan.

Is there a problem with my Jeep Laredo?

I have a 2006 Jeep Grand Cherokee Laredo with 80k+ miles. (Bought it used at 29k miles). I have been experiencing random electrical problems. The symptom is that the all the lights and gauges on the dash cluster go on and off erratically and sometimes stay off for a few minutes.

Where is the ignition switch on a Jeep Grand Cherokee?

Insert the ignition key into the key cylinder. Rotate the slot in the ignition switch to the “ON” position. The slot is located on the back of the ignition switch. Position the slot so it is just beyond a 90-degree angle. Attach the two electrical connections to the back of the ignition switch.

Why do the lights go off on my Jeep Grand Cherokee?

The symptom is that the all the lights and gauges on the dash cluster go on and off erratically and sometimes stay off for a few minutes. This also includes the A/C system. As the gauges go off so does the A/C fan. I have taken the Jeep to the dealer now going on 5 or more times and quite frankly, they are stumped.

What causes a Jeep Grand Cherokee to not start?

Jeep Grand Cherokee Won’t Start Diagnosis. 1 1. Battery Cables. While the battery cables are not necessarily the most likely issue to cause your Grand Cherokee to not start, they are some of the 2 2. Battery Charge. 3 3. Starter. 4 2. Ignition Issues. 5 3. Engine Timing.

When to reset the Immobilizer on a Jeep Grand Cherokee?

The system is activated when something other than an authorized key is used to try to start the engine. Most models are also equipped with an alarm system as part of the security system. If something triggers the immobilizer or the alarm system, you need to reset and rearm the system.

Can a bad ignition switch keep a Jeep Cherokee from starting?

A bad ignition switch can cause your Cherokee not to start at all. And, it can keep your Cherokee from starting in a couple of different ways. The first is when the starter cranks, but the bad ignition switch doesn’t turn on the fuel pump or ignition.

What to do if your Jeep Grand Cherokee won’t start?

When a starter goes bad, they will usually not give you much warning first. Also, if you are stuck somewhere and are trying to start your Grand Cherokee, the old beat the starter with a hammer trick is not a wives tale. It really can get that one last start out of it.

How can I tell if my Jeep Grand Cherokee is shifting?

Turn ignition key ON and OFF three times, finally leaving the key in the ON position. Leave the Overdrive Off Switch in the normal overdrive (ON) position. Immediately begin counting the number of flashes displayed by the Overdrive Off Switch indicator lamp. There will be two sets of flashes, separated by a pause.

If you have a model of Grand Cherokee which only has a key fob with start/stop button and no place to insert a key, then try placing your key fob as close to the start/stop button as you can and then start the vehicle. Tip: You can try starting your Grand Cherokee with its second key.

Why is there no key in my Jeep?

Right after we closed the doors they ignition viewer said “NO KEY IN VEHICLE” and disabled the Jeep. Sure enough nothing would work, couldnt unlock the doors from inside, couldnt unlock with remote or even lock with remote. Took the key fob apart to get to the spare key and popped the push button start out and nothing key wouldnt turn.

How does the ignition work on a Jeep Cherokee?

First, the key-switch engages the vehicle’s accessory systems like the radio. One click further activates the rest of the system, including the engine ignition, gauges and electric fans. Turning it further engages the momentary switch that sends power to the starter and turns the engine over.

Why is My Jeep Grand Cherokee not recognizing my key?

It is the ignition switch. It is not recognizing your key correctly. The car basically thinks it is being stolen and shuts down. The dealer changed my ignition switch in Nov. of ’06 and I have not had the same problem since. Fortunately for myself the Jeep was still under warranty. I can’t imagine this is cheap.

How does the SmartKey work on a Jeep Grand Cherokee?

Then with the key in the OFF position, press the C/T and Reset buttons on the Overhead Console (EVIC), Turn the Ignition Switch to the ON Position (not Start the Engine), and release both buttons, and then a message will appear on the Overhead Console Screen, and tell you if the Test has been passed or not.

Why does my Jeep Grand Cherokee not start?

It might be the ignition switch, but the Jeep is still driveable. If it was the ignition switch, it would just shut down after a few seconds after starting the engine. I have a 2001 JGC and one day I went to start the Jeep and all the dash board icons were lit up along with all my gauges being dead.

What’s the pin out on a Jeep Grand Cherokee?

You can find the 1996-1998 4.0L Jeep Grand Cherokee PCM connector pin-out charts here: PCM Pin Out Chart (1996-1998 4.0L Jeep Grand Cherokee). Here are some very important safety precautions when testing the wires coming out of the 60 pin PCM connector.

What was the problem with my 2008 Jeep Grand Cherokee?

Tl the contact owns a 2008 Jeep Grand Cherokee. While driving, the ignition switch would turn off independently and the vehicle stalled. The vehicle was restarted and was able to drive normally. There were no warning indicators illuminated. The vehicle was not taken to a dealer or an independent mechanic for diagnostic testing.

Is there a problem with the ignition switch?

Have had the ignition switch recall performed and also have had the new ignition switch replaced twice but problem continues. Very dangerous situation to drive at night with unreliable lights. After turning off engine, key fob is seized in ignition switch, but releases after period of time.

What are the symptoms of a bad ignition switch?

The most noticeable symptom of a bad ignition switch is stalling. Your Cherokee stalls because the faulty switch turns off the fuel pump or power to the ignition. When this happens, the engine will not be able to run until it gets that signal back. 2. Starts then Dies

What are the warning lights on a jeep?

The following are warning lights and indicators found in vehicles built by Jeep. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray), but there are nearly 80 of them so be patient!

Why is my 2008 Jeep Grand Cherokee not turning over?

Have had to jump start 4 times and carry a portable starter with me. 2008 Grand Cherokee began experiencing intermittent starting problems. Without warning the vehicle would not turn over. All dash lights were working. As well as radio, AC, power windows and all other electrical systems. No codes showed on the computer.

Where is the neutral safety switch on a Jeep Cherokee?

This is the source of the Jeep’s ignition issues, but is easily replaced by any mechanically competent owner. The neutral safety switch is located on the transmission, where the shift lever attaches. Replacing it simply involves removing the attached wires, pulling out the sensor, installing the new one and adjusting it.

What’s the code on my Jeep Grand Cherokee?

Started misfiring with one code coming up P0351, which is cylinder#1 secondary ignition fault code. I replaced the complete coil pack and same code came up , then several other codes would come up all in relation to cylinder misfires. DO NOT replace you ignition coil pack with Autozone.

What can cause a Jeep Grand Cherokee to misfire?

There is more to your Grand Cherokee’s ignition system than just the coil packs. There’s also spark plugs and plug wires. There are also non ignition related circumstances that can cause a misfire. That would include lack of fuel pressure, bad fuel injectors, or even a timing chain (or belt) that has jumped.

When did I start my Jeep Grand Cherokee ignition?

Ignition System Wiring Diagram (1993-1995 4.0L Jeep Grand Cherokee). Ignition System Wiring Diagram (1996-1998 4.0L Jeep Grand Cherokee). TIP 1: Two of the ignition coil tests in this tutorial require that you crank the engine… so, you’ve got to be careful and use common sense as you take all necessary safety precautions.

How do you test a Jeep Grand Cherokee coil pack?

You can test the coil pack in your Jeep Grand Cherokee by measuring the electrical resistance of the coil pack with an ohmmeter. Put on your safety glasses and open the hood. Disconnect the negative cable from the battery and place it out of the way so that it will not make contact with the battery terminal while you work. Locate the coil pack.

Why is the ignition coil on my Jeep not working?

Here are some more specific symptoms your Jeep will experience: You won’t see spark firing from all of the spark plug wires. The fuel injectors will still work and spray fuel into the cylinders. The PCM will still activate the ignition coil. This means that the ignition coil does receive the switching signal but fails to fire spark.

How do you repair an ignition switch on a jeep?

This Jeep repair is basically in three phases, as you remove the lower dashboard trim, remove the old ignition switch, and install the new ignition switch. Open the hood of the car and secure it. Take your wrench and detach the car battery from the negative cable terminal (black).

Can a Jeep Grand Cherokee Drive in two gears?

You’re often still able to drive the vehicle, but it only operates in one or two gears. For example, you may find that you’re only able to drive the car in the automatic transmission’s third gear, only being able to select the other two gears when you shift the transmission manually.

Why does my Jeep Grand Cherokee not shift gears?

For example, you may find that you’re only able to drive the car in the automatic transmission’s third gear, only being able to select the other two gears when you shift the transmission manually. The most common cause of transmission problems is the easiest to fix: check the fluid level in the transmission and restore it to the proper levels.

When did my Jeep Grand Cherokee ignition fail?

The contact owns a 2008 Jeep Grand Cherokee. While driving 45 mph, the engine seized and shut off. The contact was able to park the vehicle on the side of the road and restart it with no issue. The contact stated she experienced the failure again on July 12, 2019.

What does a fuse do on a Jeep Grand Cherokee?

Fuse box diagram (fuse layout), location, and assignment of fuses and relays Jeep Grand Cherokee (ZJ / ZG) (1996, 1997, 1998). A fuse is an element for protecting the electrical system. A fuse will trip (i.e. it will blow) in the event of a failure or improper interventions in the electrical system.

What kind of wiring harness does a Jeep Wrangler use?

Plug and play trailer tow hitch wiring harness for 07-18 JK Jeep Wrang… This front door wiring assembly from Omix fits 94-96 Jeep Cherokee XJ…. This wiring harness assembly from Omix fits 1996 Jeep Cherokee XJ with… This transmission wiring harness assembly from Omix fits 94-96 Jeep Ch…

Is there a recall on the Jeep Grand Cherokee?

Two years ago, the contact stated that he received a recall notice under NHTSA campaign number: 14v438000 (electrical system). The contact took the vehicle to mac haik jackson cdjr (5395 interstate 55 north frontage rd, jackson, ms 39211) where he had the vehicle serviced and repaired for the recall.

How many ignition coil wire clips are there?

Only 19 left in stock – order soon. . Only 6 left in stock – order soon. . Only 1 left in stock (more on the way). . Only 3 left in stock – order soon.

How is the O’Reilly direct ignition coil rated?

5 out of 5 stars. Read reviews for Import Direct Ignition Coil When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures. When autocomplete results are available use up and down arrows to review and enter to select.

Navigation