How to correct the speedometer on a Jeep Liberty?
Options 1-5 select the revs/mile of the stock sized tires, use 6 to manually enter revs/mile. Use the up and down arrows to select the desired revs/mile, then press enter. It will now show the new revs/mile. The BCM and odometer will now read correctly. The speedometer now needs to be corrected. Hit, “Back Page” until you come to this screen.
How to reset your Jeep engine control module?
3- Once the time has passed you should now turn the headlights “on” and “off” twice to drain the Engine Control Module from any remaining power. 4- Now plug back in the negative terminal and your Jeep ECM should now be reset. To finish off this post , here are a couple of things you should keep in mind.
How to correct tire size on Jeep Liberty?
This is a “how-to” reprogram the BCM and ACM in the Jeep Liberty to correct for different size tires. Please note that this can only be accomplished via a DRBIII. This procedure only works for 2005 and older Jeep Liberty’s, for 2006+ a starscan instead of the DRBIII is required.
Can a drbiii be used on a Jeep Liberty?
Please note that this can only be accomplished via a DRBIII. This procedure only works for 2005 and older Jeep Liberty’s, for 2006+ a starscan instead of the DRBIII is required. For those in the Colorado area wishing to have this done I do offer DRBIII programming. Please contact me here for programming cost and availability.
How to use the manual on a Jeep Liberty?
CONTENTS Introduction ……4 Roll Over Warning ….. 4 How To Use This Manual . 4 INTRODUCTION INTRODUCTION Thank you for selecting a Jeep Liberty and welcome to our worldwide family. This is a specialized utility vehicle designed for both on-road and off-road use.
How to remove ignition key from Jeep Liberty?
If you received your keys without the bag, ask your dealer to give you the number. Page 13 To remove the ignition key on models with an automatic transmission, place the gearshift lever in P (Park), turn the ignition key to LOCK and remove the key.
What to do when leaving a Jeep Liberty?
• When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Power Door Locks — If Equipped A door lock switch is on each front door panel. Press this switch to lock or unlock the doors. If the plunger is down when the door is closed, the door will lock.
Is there a steering wheel lock on a Jeep Liberty?
STEERING WHEEL LOCK — IF EQUIPPED Your vehicle may be equipped with a passive steering wheel lock (manual transmission only). This lock pre- vents steering the vehicle without the ignition key.
How does the fuel gauge work on a Jeep Liberty?
1. Fuel Gauge The fuel gauge shows level of fuel in tank when ignition switch is in the ON/RUN position. 2. Fuel Door Reminder This symbol indicates the side of the vehicle where the fuel cap is located. 3. Low Fuel Light This indicator lights when the fuel level drops to approximately one-eighth tank.
What is the malfunction indicator light on a Jeep Liberty?
The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system, called OBD, that monitors engine and automatic transmission control systems. The light will illuminate when the key is in the ON/RUN position, before engine start.
When does the oil chime sound on a Jeep Liberty?
The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine.
The Malfunction Indicator Light (MIL) is part of an onboard diagnostic system, called OBD, that monitors engine and automatic transmission control systems. The light will illuminate when the key is in the ON/RUN position, before engine start.
1. Fuel Gauge The fuel gauge shows level of fuel in tank when ignition switch is in the ON/RUN position. 2. Fuel Door Reminder This symbol indicates the side of the vehicle where the fuel cap is located. 3. Low Fuel Light This indicator lights when the fuel level drops to approximately one-eighth tank.
The light should turn on momentarily when the engine is started. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine.
When to cycle the shift key on a Jeep Liberty?
This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a problem is detected, the light will come on while the engine is running. Cycle the ignition key when the vehicle has completely stopped and the shift lever is placed in the PARK position. The light should turn off.
Is there an odometer error on my Jeep Cherokee?
If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: g14H0BmVV7mJPFPU)
When to replace the gauge cluster on a Jeep Cherokee?
This video shows the process for replacing a Jeep Cherokee instrument cluster / gauge cluster and correcting the mileage. This process can also be used for upgrading from the idiot light cluster to the full gauges. This procedure applies to all 1997-2001 Jeep Cherokees (XJ). This procedure should also apply to 1997-2001 Jeep TJ Wranglers.
Options 1-5 select the revs/mile of the stock sized tires, use 6 to manually enter revs/mile. Use the up and down arrows to select the desired revs/mile, then press enter. It will now show the new revs/mile. The BCM and odometer will now read correctly. The speedometer now needs to be corrected. Hit, “Back Page” until you come to this screen.
What to do if your speedometer is not working?
The VSS is usually not very expensive, and they are not that difficult to replace. Vehicles used to use a cable that would usually run from the tail shaft of the transmission to the speedometer. There was a physical/mechanical connection between the drivetrain and the speedometer.
This is a “how-to” reprogram the BCM and ACM in the Jeep Liberty to correct for different size tires. Please note that this can only be accomplished via a DRBIII. This procedure only works for 2005 and older Jeep Liberty’s, for 2006+ a starscan instead of the DRBIII is required.
What is the ECU on a Jeep Liberty?
ECU – Your Liberty’s Engine Control Unit (ECU for short) is the computer that takes all of the information that the vehicle sensors compile and uses it to control the vehicle systems, and sends important vehicular telemetry data to the driver via the instrument cluster.