Why is my Jeep Grand Cherokee key not working?
I have a 2014 Jeep Grand Cherokee and the key fobs don’t always work. They won’t unlock the Jeep or start it. When I open the door with the key the alarm always goes off and takes a few minutes for it to stop. I have states that the key has left the vehicle..
Why is my Jeep fob remote not working?
Guess it’s the WCM (whatever that is) within the Jeep. Wireless control module… Typically if a dealer needs to reset something there is another underlying cause… Not that I would have ANY idea what that is over the interwebz. Personally I have never had to reset a wcm to repair a key problem.
Why is my car key fob not working?
The battery holds the key for communicating with the relay modules installed in your vehicle. You might at some point notice that the key fob is acting up, like finding it difficult to lock or unlock your vehicle doors. This can be caused by the weak battery in the key fob.
How do you turn off the FOB on a car?
Make sure that the ignition is not in the radio mode, and do not start the engine. With the key in the ‘On’ position, press the fob’s lock button and turn the key back to the ‘Off’ position. Repeat this process at least three times, ending the cycle with the key in the ‘On’ position.
What to do if your Jeep Grand Cherokee key fob is not working?
There is a little slot, using a dime or a small screwdriver open the 2 halves. note which way the + side is oriented. Check the battery with a multimeter. If you don’t have a meter buy a new battery (they’re relatively inexpensive. The number is printed on the face of the battery.
Why is my 2016 Jeep Grand Cherokee not turning on?
Guru1B3BJ same thing happened to my 2016 Jeep Cherokee. Did you find out what was wrong? My 2014 grand Cherokee isn’t turning on and both key fobs don’t work. The dash does not state key fob not detected.. HELP!
What to do if your key fob is not working?
If you don’t have a meter buy a new battery (they’re relatively inexpensive. The number is printed on the face of the battery. If that doesn’t work you’ll have to replace it. Amazon or Ebay are good sources. You can’t post conmments that contain an email address.
How can I Fix my Jeep Grand Cherokee?
An expert that got 5 achievements. Visited the website for 3 consecutive days. An expert that has 1 follower. There is a little slot, using a dime or a small screwdriver open the 2 halves. note which way the + side is oriented. Check the battery with a multimeter.
Why does my 2016 Jeep Cherokee not start?
My 2016 jeep will not start. It has a key fob. The brake My 2016 jeep will not start. It has a key fob. The brake pedal is stiff. … read more It starts then the security system shuts it down. Both my Hello, it starts then the security system shuts it down. Both my key fobs are bad. … read more
Why is my FOB on my Jeep not working?
No message saying fob battery was low, but thought to try that. Went into gas station to get a battery and the worker told me my battery wasn’t dead and that this happens regularly, especially dodges. Solution: got into vehicle held fob in hand and pushed start button with fob.
Do you need a key fob for a Jeep Cherokee?
Do not buy a key fob for your Jeep if you do not have a professional, such as an automotive locksmith or the dealership, that will accept it for programming. Most professionals will not program a fob that has been ordered through another dealer, for proprietary and security reasons.
What to do if your key fob doesnt work?
Went into gas station to get a battery and the worker told me my battery wasn’t dead and that this happens regularly, especially dodges. Solution: got into vehicle held fob in hand and pushed start button with fob. Started immediately. She said if that doesn’t work, use the key in same fashion.
What to do if your Jeep remote is not working?
1. Remove the battery. 2) Use 1/3 of a sticky note, fold it, and place it within the round battery slot (on the floor beneath where the battery is placed. 3) Put the battery in on the folded note. WALAAA! Thank you so much, this worked for me!!! It simply is a problem with the battery positioning within the fab. 1. Remove the battery.
How to troubleshoot a jeep that won’t start?
Fortunately, due its spacious engine compartment, the troubleshooting steps for a nonstarting jeep are easy to perform. Place your key into the ignition and turn the key as though you are trying to start your jeep. Turn on your headlights. Get out of your jeep and check to see whether the headlights came on.
What to do if your Jeep key fob dies?
Never allowed it to get low enough to try the emergency method. Think how cheap it would be to just carry a spare battery with you. They also come in two-packs. Never allowed it to get low enough to try the emergency method. Click to expand… Works fine. When I first got my jeep I took the battery out of the remote and tried it. Works fine.
What to do if your car key won’t start?
However, before you assume that there is a problem with the car’s engine or even the starter, you might consider that the key you use to start your car could be at fault.
What was the damaged key notice on my Jeep?
She then pulled the start push button off, inserted the key manually & proceeded to try and start the vehicle manually, and a notice on the display read “Damaged Key”. She went back in the house, got my key, and that seemed to work fine.
Why does my Cherokee SRT8 say damaged key?
When I put the key (both keys) in the ignition…the dash flashes “DAMAGED KEY” for an instant then nothing. The battery tested fine and lights and alarm still work. I’ve disconnected the battery, grounded it and then reconnected after 1 hour….nothing.
How can you tell if your car key is damaged?
She had her key in her pocketbook. She opened the door & the car “recognized” her. She proceeded to put her foot on the brake & push the start button & the car wouldn’t start. She then pulled the start push button off, inserted the key manually & proceeded to try and start the vehicle manually, and a notice on the display read “Damaged Key”.
Why is my Jeep SRT8 ignition not working?
I’ve called the dealer to see how much the part is and if they have to program it to my truck specifically…anytime they plug in….that’s usually when the trouble starts. The SKIM is a regualar issue on all Dodge/Chrysler/Jeep vehicles.
What to do if your Jeep Grand Cherokee won’t start?
When a starter goes bad, they will usually not give you much warning first. Also, if you are stuck somewhere and are trying to start your Grand Cherokee, the old beat the starter with a hammer trick is not a wives tale. It really can get that one last start out of it.
When did my Jeep Grand Cherokee Overland stop working?
December 2014 had a Jeep Grand Cherokee Overland built for me. December 2019 vehicle stopped functioning operating all together. Dealer has had the vehicle and working in tandem with the manufacturers’ master mechanics to figure out the problem (s). They replaced the TIPM and hub parts.
Is there a recall on the Jeep Grand Cherokee?
In addition, the SUVs may not start at all or the fuel pumps may keep running while the vehicles are shut down. A Chrysler TIPM recall was ordered for the SUVs in 2014 following a federal petition filed by the Center for Auto Safety which asked the government to investigate 7 million Chrysler vehicles.
Why does my 2002 Jeep Grand Cherokee not start?
SOMETIMES VEHICLE (2002 JEEP GRAND CHEROKEE) WON’T START. YOU GET NOTHING WHEN YOU HIT THE KEY, NO CLICKING, NO NOTHING. YOU MAY GO BACK LATER AND IT WILL START. GAUGES GO CRAZY. WILL COME ON. ODOMETER AND CLOCK WILL FLASH. SOMETIMES SPEEDOMETER WILL GO FROM 60 TO ZERO AND BACK. WILL NOT LOSE POWER THOUGH.
Why is there no key in my Jeep?
Right after we closed the doors they ignition viewer said “NO KEY IN VEHICLE” and disabled the Jeep. Sure enough nothing would work, couldnt unlock the doors from inside, couldnt unlock with remote or even lock with remote. Took the key fob apart to get to the spare key and popped the push button start out and nothing key wouldnt turn.
Is there a problem with my Jeep FOB?
Put in new batteries an all’s well for 2-3 weeks and the issues return. Just took the fob apart, bent the four battery contacts as well as the side contact. Right now it’s working properly. The dealer couldn’t recreate the problem last month.
How can I unlock a locked steering wheel?
1. Try pulling the key out a very small amount before gently turning key. (About 1/16 of an inch, the thickness of a nickel). 2. Wiggle key while trying to turn key gently.
1. Remove the battery. 2) Use 1/3 of a sticky note, fold it, and place it within the round battery slot (on the floor beneath where the battery is placed. 3) Put the battery in on the folded note. WALAAA! Thank you so much, this worked for me!!! It simply is a problem with the battery positioning within the fab. 1. Remove the battery.
Went into gas station to get a battery and the worker told me my battery wasn’t dead and that this happens regularly, especially dodges. Solution: got into vehicle held fob in hand and pushed start button with fob. Started immediately. She said if that doesn’t work, use the key in same fashion.
Why does my Jeep not unlock the passenger side door?
The power lock motor operates in 2 directions, by reversing the current. So if the motor works in one direction, the motor itself is ok. So maybe it is some wiring problem to the unlock side. The passenger side doors, the LH aft door and the liftgate are all controlled from the Passenger Door Module.
Can you open the trunk of a Jeep Grand Cherokee?
If you or anyone at all gets locked up inside of the trunk of a Jeep Grand Cherokee then you can easily pull on the latch to open it. This is really good input from the designers and engineers since it could literally save someone’s life if there was ever a situation of that sort. How to Open a Stuck Rear Hatch Door of a Jeep Grand Cherokee?
I have a 2014 Jeep Grand Cherokee and the key fobs don’t always work. They won’t unlock the Jeep or start it. When I open the door with the key the alarm always goes off and takes a few minutes for it to stop. I have states that the key has left the vehicle..
December 2014 had a Jeep Grand Cherokee Overland built for me. December 2019 vehicle stopped functioning operating all together. Dealer has had the vehicle and working in tandem with the manufacturers’ master mechanics to figure out the problem (s). They replaced the TIPM and hub parts.
In addition, the SUVs may not start at all or the fuel pumps may keep running while the vehicles are shut down. A Chrysler TIPM recall was ordered for the SUVs in 2014 following a federal petition filed by the Center for Auto Safety which asked the government to investigate 7 million Chrysler vehicles.
What to do if your Jeep won’t start?
With the key in the “start” position, if the starter motor is getting power but the starter doesn’t work, then the starter is condemned and replaced. Note that starters can and do sometimes develop intermittent faults due to bad spots on the armature.
What to do if your Jeep key fob is damaged?
Can get Duracell or Energize for like 3-5 dollars shipped for all five. Can’t beat that. Hmm…wife was out in the Jeep this morning with her key FOB with the brand new battery. Walked up to the car, opened/unlocked the door fine, proceeded to try and start the far and got “Key not Detected”.
What happens when there is no power in a jeep?
If there is no power, then the electrical circuit supplying the motor has a fault. That circuit begins at the battery and includes grounds, wiring (some of which is very heavy cabling), fuses, relays, the ignition switch and terminations.
With the key in the “start” position, if the starter motor is getting power but the starter doesn’t work, then the starter is condemned and replaced. Note that starters can and do sometimes develop intermittent faults due to bad spots on the armature.
Can get Duracell or Energize for like 3-5 dollars shipped for all five. Can’t beat that. Hmm…wife was out in the Jeep this morning with her key FOB with the brand new battery. Walked up to the car, opened/unlocked the door fine, proceeded to try and start the far and got “Key not Detected”.
How do you manually start the car when the key fob battery is dead?
– CarGurus how do you manually start the car when the key fob battery is dead? You cannot. You need to change the battery in the key FOB. The Key FOB is plastic and can be pried open to get the old battery out. They cost a couple of bucks, and you are back in business. The anti- theft security system will not allow you to manually do anything.
Why is my 2008 Jeep Grand Cherokee not turning over?
Have had to jump start 4 times and carry a portable starter with me. 2008 Grand Cherokee began experiencing intermittent starting problems. Without warning the vehicle would not turn over. All dash lights were working. As well as radio, AC, power windows and all other electrical systems. No codes showed on the computer.
When did I Buy my 2008 Jeep Grand Cherokee?
I bought my biggest problem to date, my 2008 Jeep Grand Cherokee Diesel, September 17, 2013. This vehicle has caused me nothing but problems, thousands of dollars and has been a major headache since I bought it. On Nov 14, 2016 I had it in for service and that evening I was rear ended on the highway.
How do you get the ignition key out of a jeep?
Access the solenoid: Lift the rubber mat off the tray and remove the two tray screws. You will see the solenoid. It’s a white cylinder with a metal bar protruding rearward toward the shifter. You might opt to remove the center console too. Quick Fix: If you’re in a jam and need to remove the key without disassembling things read on.
Why does my Jeep FOB not unlock the door?
What is weird is that I usually have this issue after driving the Jeep for awhile and shutting it off for 5 minutes or so, then I can’t get back in unless I hit the unlock button 10-15 times. Sure is embarrassing standing there beside the Jeep not being able to get back in. And if you use the key to unlock the door you set off the alarm! Exactly.
Is there a way to reprogram a jeep key fob?
I quickly inserted into the ignition thinking that’s going to help reprogram the key fob. Took it out it hit the unlock and lock button and it worked again Not sure if this applies to the WK but on the WK2, several people have also noticed the same issue the OP described with the keyless lock button on the door handle.
Are there leather key fobs for Jeep Grand Cherokee?
Only 9 left in stock – order soon. . Only 9 left in stock – order soon. Leather Car Key Fob Cover, Suit for Keyless Control for Jeep Grand Cherokee Dodge Challenger Charger Dart Durango Journey Chrysler 200 300 Fiat etc (A Style, Blue) … …
Where can I get a 1998 Jeep FOB?
Taking it to the dealership can be rather expensive, so consider a reputable automotive locksmith for programming your 1998 Jeep Grand Cherokee key fob. Call your local Jeep dealership. Ask how long it will take to obtain a 1998 key fob for your Jeep Grand Cherokee.
Is there a locksmith for a 1998 Jeep Grand Cherokee?
Unfortunately, the 1998 Jeep Grand Cherokee is not one of these models. The dealership or an automotive locksmith must be consulted to program your key fob. Taking it to the dealership can be rather expensive, so consider a reputable automotive locksmith for programming your 1998 Jeep Grand Cherokee key fob.
What is weird is that I usually have this issue after driving the Jeep for awhile and shutting it off for 5 minutes or so, then I can’t get back in unless I hit the unlock button 10-15 times. Sure is embarrassing standing there beside the Jeep not being able to get back in. And if you use the key to unlock the door you set off the alarm! Exactly.
What’s the problem with my 1998 Jeep Cherokee?
1998 jeep Cherokee classic has door locking/unlocking problem. sometimes they work and sometimes they don’t. passenger door lock makes a ticking noise when I push the door lock on drivers door. nothing will lock or unlock electronically. any help on how to fix would be very helpful. oldman44oldjeep98, May 1, 2018.
What kind of door lock does a Jeep Cherokee have?
Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37″ Toyo MTs. I will assume you have a 4 door Cherokee.
1998 jeep Cherokee classic has door locking/unlocking problem. sometimes they work and sometimes they don’t. passenger door lock makes a ticking noise when I push the door lock on drivers door. nothing will lock or unlock electronically. any help on how to fix would be very helpful. oldman44oldjeep98, May 1, 2018.
Why does my Jeep Grand Cherokee lock not work?
Please try again later. 2004 Jeep grand cherokee power door locks and windows stopped working. found the problem and fixed it. Also the interior lights would not turn off and the jeep did not register as an open door. the FoB lock would not work either. Loading…
Howell fuel injection, header, HEI distributor, TH350, NP208, SOA lift with YJ springs in the front & GW springs in the Rear. AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37″ Toyo MTs. I will assume you have a 4 door Cherokee.
Why is my passenger door lock not working?
If the passenger door button doesn’t work you will have to dig deeper and figure out where the problem is like 2oldjeeps says. The switch is the most common problem though. The door lock circuit is actually in the passenger door. I have an issue with my 00 XJ where they will work only occasionally and I can hear one of the relays clicking.
What to do if your Jeep Grand Cherokee wont start?
First get new batteries for your keys; there might be a little screw. After trying new batteries for the keys, DISCONNECT THE BATTERY AND WAIT ABOUT TEN MINUTES; RECONNECT BATTERY AND START CAR. This should at least get you to where you need to go.
What kind of problem does a Jeep Grand Cherokee have?
2008 Jeep Grand Cherokee Laredo. 3.7 V6. Won’t start. All lights on the dash work, the radio/clock, etc. Turn the key and there is nothing, no noise like when the battery is dead, nothing. This is the second episode of this happening. First episode had the car towed to a shop where they could not fix it but kept it overnight.
Why are my key fobs not recognizing my Car?
Having an issue with just ONE of our two key fobs. (FYI, the “problem” fob has a brand new battery). On occasion (intermittently), the problem fob will open the door, adjust the seat, etc., to all the pre-programmed settings and then not start the car with the push button, and get the notification “Key Not Recognized”.
How to check for diagnostic trouble codes on a Jeep Grand Cherokee?
If you own a 1999-2010 Jeep Grand Cherokee, and your ‘Check Engine’ light is on, you can easily check for Diagnostic Trouble Codes (DTC’s) without a scanner using just a simple key sequence. Steps. Get into your vehicle and make sure the hood, rear tailgate, and all doors on your vehicle are shut.
I quickly inserted into the ignition thinking that’s going to help reprogram the key fob. Took it out it hit the unlock and lock button and it worked again Not sure if this applies to the WK but on the WK2, several people have also noticed the same issue the OP described with the keyless lock button on the door handle.
Can a key fob set off an alarm?
Sure is embarrassing standing there beside the Jeep not being able to get back in. And if you use the key to unlock the door you set off the alarm! Exactly. Setting off the alarm in a parking lot is rather embarrassing.
Sure is embarrassing standing there beside the Jeep not being able to get back in. And if you use the key to unlock the door you set off the alarm! Exactly. Setting off the alarm in a parking lot is rather embarrassing.