What does trouble code p0133 on oxygen sensor mean?
This trouble code involves the front oxygen sensor on Bank 1. This code indicates the engine air fuel ratio is not being adjusted by the oxygen sensor signal or the ECM as expected to do so, or not adjusted as often as expected to do so once the engine is warmed or under normal engine use.
What is the problem code for the O2 sensor?
P0133 – O2 Sensor Circuit Slow Response (Bank 1 Sensor 1) P0156 – O2 Sensor Circuit Slow Response (Bank 2 Sensor 2) P0411 – Secondary Air Injection System Incorrect Flow Detected Thanks for …
What is the trouble code for OBD-2 Bank 1?
That means it’s definition is the same for all makes and models of OBD-II vehicles, however specific repair steps may vary depending on the vehicle. This trouble code involves the front oxygen sensor on Bank 1.
What causes the p0138 code on a Jeep Liberty?
Here are the most common issues that cause the P0138 code in the Jeep Liberty. They are presented in order (somewhat) of most to least likely to cause the problem. Bad Oxygen Sensor – The O2 sensor itself is one of the most likely reasons that P0138 is triggering your service engine soon light.
What is the oxygen sensor code on a Jeep Liberty?
Jeep Liberty P0138: Oxygen Sensor High Voltage (Bank 1 -Sensor 2) P0138 is a common OBDII code that occurs in many vehicles, including theJeep Liberty. The code is triggered when: There are also some less likely problems that can cause P0138.
What does the p0123 code on a jeep mean?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost to diagnose the P0123 JEEP code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
What is the diagnostic code for a jeep check engine light?
Refer to our Generic OBD II code list for definitions on all other Jeep diagnostic trouble codes. Manufacturer Specific Codes P1105Open Or Shorted Condition Detected In The Baro Read Solenoid Control Circuit – Read Our Article on Automotive Circuit TestingFor Help With This Jeep Check Engine Light Code P1192Inlet Air Temp. Circuit Low
Where is the trouble code on a Saturn?
These are listed in numerical order for easy searching. When retrieving Saturn trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.
What causes the O2 sensor circuit ” slow response “?
P0133 indicates the ECM senses that the O2 Sensor is not changing its voltage output quickly enough to the changing air-fuel ratio. Hence why the P0133 trouble code definition is O2 sensor circuit “slow response” because the circuit is not reacting quickly enough. What causes the P0133 code?
This trouble code involves the front oxygen sensor on Bank 1. This code indicates the engine air fuel ratio is not being adjusted by the oxygen sensor signal or the ECM as expected to do so, or not adjusted as often as expected to do so once the engine is warmed or under normal engine use.
P0133 – O2 Sensor Circuit Slow Response (Bank 1 Sensor 1) P0156 – O2 Sensor Circuit Slow Response (Bank 2 Sensor 2) P0411 – Secondary Air Injection System Incorrect Flow Detected Thanks for
These are listed in numerical order for easy searching. When retrieving Saturn trouble codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.
What does Bank 1 O2 sensor 1 do?
All our repairs are backed by our 12-month / 12,000-mile warranty. Bank 1 Sensor 1 is a sensor that is used by the computer (ECM) to monitor the amount of oxygen exiting the engine. The ECM uses the signal from the O2 sensor to adjust the fuel and air ratio of the engine.
What is the OBD code for oxygen sensor?
OBD-II Code P0133 is defined as an Oxygen Sensor Circuit Slow Response (Bank 1, Sensor 1) Code P0133 is triggered when the powertrain control module or PCM determines that the oxygen sensor voltage switch from below 400 millivolts to above 450 millivolts is taking too long.
What is the diagnostic code for O2 sensor circuit slow?
Cost of diagnosing the P0133 code. P0133 is a diagnostic trouble code (DTC) for “O2 Sensor Circuit Slow Response (Bank 1 Sensor 1)”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.
What to do when the freeze frame code is p0133?
When the code P0133 is set, record the freeze frame data in fine detail. Next, duplicate the code setting conditions on a test drive, paying particular attention to load, MPH, and RPM. The best tool to use on this test drive is a data streaming scan tool that has factory quality, dedicated live data.
What does the p0333 code on my car mean?
All our repairs are backed by our 12-month / 12,000-mile warranty. The P0333 code indicates that your car’s computer has detected an input reading for one cylinder’s knock sensor circuit that goes beyond the manufacturer’s limit.
What is the diagnostic code for knock sensor 2?
P0333 is a diagnostic trouble code (DTC) for “Knock Sensor 2 Circuit High Input (Bank 2)”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.