What kind of problem does a Jeep Liberty have?
:sick: I have a 02 Liberty 3.7L V6. about 85,000 miles on it. never had a problem till two weeks ago. driving down the road and the car just starts stalling with the RPM gauge going nutz, then the cabin fills up with gas fumes,blows black smoke only when it starts acting up, check engine lite stays on, but not blinking.
Why does my Jeep Liberty stall at start up?
Since the Liberty is only a 2003, I can’t imagine any switch inside the vehicle going bad. In the engine compartment, it could several components which might be suspect. The gripe is, too much “juice” at start-up, therefore burning up the starter and or switch. It is simple to conclude there is an electronic short somewhere in the system.
What happens if the starter on a Jeep Liberty is fried?
If the starter is being fried, then the starter has been placed in a postion as a “fusable link”. I venture to say that much of the Liberty’s wiring has been put under tremendous strain from over-voltage, that even if its fixed, then unsafe situations in the wire’s integrity are almost guaranteed.
Why does my Jeep Liberty make a noise when starting?
It never made the noise prior to the first replacement and now the regional tech is trying to tell me that this noise is “normal” and due to holding the key too long. All of the tech’s at this dealer have acknowledged that the noise is not normal and is caused when the starter is dis-engaging from the fly wheel.
:sick: I have a 02 Liberty 3.7L V6. about 85,000 miles on it. never had a problem till two weeks ago. driving down the road and the car just starts stalling with the RPM gauge going nutz, then the cabin fills up with gas fumes,blows black smoke only when it starts acting up, check engine lite stays on, but not blinking.
Since the Liberty is only a 2003, I can’t imagine any switch inside the vehicle going bad. In the engine compartment, it could several components which might be suspect. The gripe is, too much “juice” at start-up, therefore burning up the starter and or switch. It is simple to conclude there is an electronic short somewhere in the system.
How long does it take for a Jeep Liberty to start?
The last two days I’ve ran the vehicle in the company parking lot for ten minutes so it won’t die on the road. It starts ok, but runs a little rough. After about five minutes, the Tach goes from 600 rpm (Idle) to 5000 rpm (the engine does not rev up) then to zero. the engine dies.
It never made the noise prior to the first replacement and now the regional tech is trying to tell me that this noise is “normal” and due to holding the key too long. All of the tech’s at this dealer have acknowledged that the noise is not normal and is caused when the starter is dis-engaging from the fly wheel.
What makes a Jeep Liberty not to start?
Car starts when engine is cold, but only cranks, no fire once it has been started until the following morning. Also, no heat, only blows cold. This all happens at the same time. Took it to mechanic last week, they said needed I new computer.
What was the worst year for Jeep Liberty?
It seems like the 2006 model year was the worst one for the Jeep Liberty. There were numerous complaints relating to issues with the windows. The window regulator broke routinely, and that led to a number of drivers experiencing the window simply falling open.
What’s the problem with my Jeep Liberty window?
Many drivers also expressed a problem with window regulator failure. This was a recurring issue with the number of vehicles in which the window would either only have open or closed and the motor that operated the window would make quite an annoying sound while you’re trying to operate it.
What was the rating of the Jeep Liberty in 2006?
Based on the Insurance Institute for Highway Safety crash testing, the 2006 Jeep Liberty was also poorly rated, in particular is it related to rear crash test results. The Jeep Liberty fared a little bit better in 2007 than it did in 2006 in terms of problems reported by drivers.
What should I do if my Jeep Liberty won’t start?
When this module fails the remote keyless entry system will also not operate. The WCM is commonly replaced to correct this concern. The average cost for a Jeep Liberty No Start Diagnosis is between $88 -$111. Learn More
What to do if your Jeep Liberty is having transmission problems?
Good on Jeep for changing a couple axles. Troubleshooting while driving, especially when the noise if coming from under the car is very hard to isolate. What about putting the car on one of those machines where the rear tires move on rollers but the car remains stationary.
Why does my Jeep Liberty refuse to drive?
If they find nothing, its not the transmission, axle, U-joints or any mechanical linkage. What about the body. Sometimes, a pet will refuse to ride in a particular car or truck because it has a body (weld integrity) problem and emits very high frequencies.
Are there any problems with the Jeep Liberty 3.7 engine?
According to one leading engine builder, Chrysler’s 3.7-liter engine has some fatal flaws. The engine builder also adds that if not attended to, there could be some serious as well as catastrophic vehicle failures just after the warranty expires.
How to troubleshoot the air conditioning on a Jeep Liberty?
Unscrew the blue valve cap and screw on the air conditioning pressure gauge. Turn the knob on the pressure gauge counterclockwise to allow pressure into the gauge. Check the gauge reading. Your AC pressure gauge should be color coded.
How to troubleshoot a Jeep Liberty’s transmission?
The main drive gear bearing or countershaft also may be damaged. Check for noise in a particular gear. This indicates worn, damaged or chipped gear teeth. The synchronizer for the gear may also be worn or damaged. Drive the vehicle and check for slippage in high gears.
Why is my Jeep Liberty stalling and stalling?
Anyway, got it towed to the garage again, this time they said it needed two what they called Transmission sensors. They replaced them free of charge. Took it out drove it around town for about 20 mins then it starts acting up again just driving down the road doing about 35 MPH. same symptoms.
What kind of engine does a Jeep Liberty have?
The 3.7 replaced the 2.5 liter four-cylinder, and then went on to replace the 3.9-liter V6 engine- which were both used only on Jeeps and Chrysler trucks. The 3.7’s first use was only an option for the Jeep Liberty. As more of a “car-like” engine, the 3.7 engine offered a 210 horsepower at 5,200 rpm, with 235 lb.-ft of torque at 4,000 rpm.
If the starter is being fried, then the starter has been placed in a postion as a “fusable link”. I venture to say that much of the Liberty’s wiring has been put under tremendous strain from over-voltage, that even if its fixed, then unsafe situations in the wire’s integrity are almost guaranteed.
Anyway, got it towed to the garage again, this time they said it needed two what they called Transmission sensors. They replaced them free of charge. Took it out drove it around town for about 20 mins then it starts acting up again just driving down the road doing about 35 MPH. same symptoms.
Where can I buy a 2005 Jeep Liberty?
Used 2005 Jeep Liberty Sport Utility 4D Prices | Kelley Blue Book See pricing for the Used 2005 Jeep Liberty Sport Utility 4D. Get KBB Fair Purchase Price, MSRP, and dealer invoice price for the 2005 Jeep Liberty Sport Utility 4D. View local inventory and get a quote from a dealer in your area.
Can you change the engine on a Jeep Liberty?
While it’s true that on rare occasions you can swap a 3.7 Jeep liberty engine, it can be dangerous to do so due to emissions standards, engine weight, bracket mounts, and PCM diagnostics. Therefore, it’s advisable to use an original 3.7 Jeep Liberty engine to get the maximum efficiency and productivity for your Jeep Liberty.
The last two days I’ve ran the vehicle in the company parking lot for ten minutes so it won’t die on the road. It starts ok, but runs a little rough. After about five minutes, the Tach goes from 600 rpm (Idle) to 5000 rpm (the engine does not rev up) then to zero. the engine dies.
Why is the service light on my Jeep Cherokee not working?
If i turn the car off and take the key out the Shifter Service light on my Dash would clear out. It didn’t happen often but im on pins and needles waiting for word back. I was told this is covered under my warranty. Anyone else had the issue and it was fixed after the shifter was replaced?
Why does my check engine light not turn off?
Sometimes your check engine light won’t turn off even after you’ve fixed the problem with your vehicle. When that happens, you’ll need to manually reset the light. One option is to turn the ignition on and off 3 times in a row. Then, drive your vehicle around and check to see if the light goes off.
Why does my Jeep Liberty sound like a jet engine?
Starter catches fine and starts right up, but any outside temp below about 40F and it sounds like a jet engine winding up or a wild cat with its tail in a fan under the hood. Only does this on cold starts and it goes away after about a block.
Why does my 2005 Jeep Liberty not start?
My 2005 Jeep Liberty decides after driving around a bit not to start. Battery is fine. And it will start again — so far — after 20+ minutes; but I wonder if one time it won’t.
When did my 2012 Jeep Liberty not start?
I have a 2012 Jeep Liberty and this started close to 2 years ago now. Randomly would not start every once in a while (it would crank but not start). Went to goodyear, they replaced my throttle body, did a bunch of other work (close to $1,000) and then 6 months later it started again.
How much does a Jeep Liberty no start cost?
The average cost for a Jeep Liberty No Start Diagnosis is between $88 -$111. Learn More Every couple of months, with no rhyme or reason, the vehcile will not start even if it was JUST running 2 minutes prior.
My 2005 Jeep Liberty decides after driving around a bit not to start. Battery is fine. And it will start again — so far — after 20+ minutes; but I wonder if one time it won’t.
What kind of noise does a Jeep Liberty make?
It does not make any noise, unless you are just a picky weirdo, hopefully not. If you paid to have the work done, then get it done right. Or record the sound and post it or email it to me. I haven’t had to pay for anything yet as it is still under the original mfgr warranty.
Check engine light on. Extreme shaking when idling. Fine once it gets going. Jeep suddenly would not start unless you aggressively apply the accelerator and maintain above 1500 RPM, it would not idle, and reported a P0306 diagnostic code (Cylinder 6 misfire). FYI the last digit is the cylinder # so you may see a different P030X.
What is the Diagnostic Code on a Jeep Liberty?
Jeep suddenly would not start unless you aggressively apply the accelerator and maintain above 1500 RPM, it would not idle, and reported a P0306 diagnostic code (Cylinder 6 misfire). FYI the last digit is the cylinder # so you may see a different P030X.
Why does my Jeep Liberty engine misfire at idle?
An engine misfire at idle (rough idle), accompanied by illumination or flashing of the check engine light, could indicate a problem with one or more of the intake valves. Revised intake valves & valve locks are available to address this concern.
When did I buy a 2005 Jeep Liberty Sport?
I purchased a 2005 Jeep Liberty Sport on 12/9/10. Within 100 miles after driving it off the dealer’s lot, the check engine light came on. The dealer has had it in for repairs on 4 different occasions for a total of 37 days in three different repair shops.
What to do if your Jeep Liberty stalls?
Got all the stuff done to it, took it out 4 miles into the trip it stalls, same symptoms, RPM gauge goes nutz and smells of gas, cant restart it unless you let it sit for a few hours. Anyway, got it towed to the garage again, this time they said it needed two what they called Transmission sensors. They replaced them free of charge.
Are there any problems with the Jeep Liberty?
The Liberty was fairly popular in its day, but it was not without its problems as well. If you’re interested in picking up a used Liberty for yourself, it’s good to be familiar with the problems that the various model years were faced with.
When did the Jeep Liberty go out of production?
July 16, 2020 by Tom Harbid Jeep produced the Liberty as a compact SUV that would sit in their lineup between the Wrangler and the Grand Cherokee. It was in production for 10 years from the year 2002 until the year 2012. When it was replaced in 2012, the Jeep Cherokee took over.
Is the 2002 Jeep Liberty a good car?
According to the Insurance Institute for Highway Safety crash tests, the 2002 Jeep Liberty did not fare well overall. The rear crash test rating was actually poor while the rest was just marginal overall. It would be in your best interests to avoid this model year if possible.
What kind of powertrain does a Jeep Liberty have?
Jeep also added a four-wheel drive system and an optional sunroof. This is also the year Jeep introduced its lifetime powertrain warranty. 2009: 2009 Liberty models did not see much change from the 2008 updates other than a couple of smaller adjustments to both the interior and exterior of the vehicle.
Got all the stuff done to it, took it out 4 miles into the trip it stalls, same symptoms, RPM gauge goes nutz and smells of gas, cant restart it unless you let it sit for a few hours. Anyway, got it towed to the garage again, this time they said it needed two what they called Transmission sensors. They replaced them free of charge.
What are the symptoms of a bad crankshaft position sensor?
Cost of Replacing a Bad or Failing Crankshaft Position Sensor. Common signs of a faulty crankshaft position sensor include issues starting the vehicle, intermittent stalling, and the Check Engine Light coming on. Our certified technicians can come to you and diagnose the problem.
It does not make any noise, unless you are just a picky weirdo, hopefully not. If you paid to have the work done, then get it done right. Or record the sound and post it or email it to me. I haven’t had to pay for anything yet as it is still under the original mfgr warranty.
What causes a flashing check engine light on a Jeep Liberty?
While a majority of the time, the flashing check engine light is going to be caused by a misfire related to your Liberty’s ignition system or fuel system (as stated above), there are other issues that can cause it. Your timing chain could have jumped . If you have VVT, it may be having issues.
How to check engine light codes on Jeep Cherokee?
Jeep Check Engine Light Codes 1 Connect scan tool to the 16-pin data link connector (DLC) located near the steering column. The connector may have a removable cover. 2 Turn the ignition on. 3 Follow scan tool manufacturer’s operating instructions to access the Diagnostic Trouble Codes (DTC’s).
While a majority of the time, the flashing check engine light is going to be caused by a misfire related to your Liberty’s ignition system or fuel system (as stated above), there are other issues that can cause it. Your timing chain could have jumped . If you have VVT, it may be having issues.
Why does my Jeep Liberty not start up?
Crank/Cam Sensor- When the cam or crank sensors are not being read by the ECM/PCM, it’s impossible to get the ignition timing right. If you Liberty does start at all, it’ll run rough. It could be a more serious mechanical issue, such as as bent valve, bad lifter, etc….
Why does my check engine light keep coming on?
A failing oxygen sensor, also known as an O2 sensor, is one of the most common reasons for that Jeep check engine light to come on. And the tricky thing with the O2 sensor is that the car will continue to drive well so you might want to dismiss the light. But an O2 sensor code will surely show up in a diagnostic test.
Why is my catalytic converter not working in my Jeep?
If the wire is faulty, then the fuel and air mixture in its respective cylinder can’t ignite. This causes the rough idling. So even though your Jeep may still be running with a faulty wire, long-term use of it could cause serious damage to your catalytic converter. 4. Catalytic Converter