Why are the gauges on my Jeep YJ not working?

It is not that uncommon for Jeep Wrangler YJ dash gauges to go out and the fix can be fairly easy…. if you can find the problem. I show the steps I went through on how to fix the gauges on my 1994 Jeep wrangler YJ. 2: Cleaning the ground wires on the engine. 3: Removing the instrument cluster to check the connection of the gauges.

How does the fuel gauge on a jeep work?

The fuel gauge on your Jeep is powered by the fuel sensor relay. If the fuel gauge in your Jeep stops working, the relay has gone bad and needs to be replaced. The fuel sensor relay is responsible for powering the sensors that, in turn, relay information to your fuel gauge.

Why is the speedometer on my Jeep Wrangler not working?

While there are a variety of reasons your Jeep Wrangler speedometer is not working, the most common 3 are the vehicle speed sensor (VSS), a faulty speedometer, or an electrical issue. Due to the nature of electrical systems on modern vehicles, the range of problems these can cause are nearly limitless.

What happens when your gas gauge is not working?

The gas gauge tells you how much fuel is in your gas tank and alerts you when it’s time to refuel. If your gas gauge is not working, the inaccurate information it provides may cause you to run out of gas unexpectedly.

Why are all the lights on my Jeep Cherokee not working?

The lights work (cel, seatbelt light, air bag, etc) but the actual gauges don’t work. Any ideas of where I should check? All the grounds seem to be connected, and I haven’t made any changes with wiring in regard to the cluster.

Why is the instrument cluster on my Jeep Cherokee not working?

Checked the fuses, as well as the hot to the cluster from the fuse and back to the battery. Next plan is the grounds and then the connectors. Not liking this instrument panel

Why is the Speedo cable on my Jeep Cherokee not working?

No speedo cable. They are electronic after 91. When you moved your grounds did you grind of the paint under the ground connector? okay well im out of answers. No speedo cable. They are electronic after 91. When you moved your grounds did you grind of the paint under the ground connector?

Checked the fuses, as well as the hot to the cluster from the fuse and back to the battery. Next plan is the grounds and then the connectors. Not liking this instrument panel

How does the speedometer work on a Jeep Liberty?

A modern vehicle’s speedometer takes the input from the Vehicle Speed Sensor and sends that data to the ECU. The ECU is programmed with your Liberty’s gear ratios and stock tire height. It combines this data to send the speed reading to the instrument cluster.

Why does my Jeep Wrangler not have a dashboard?

Chrysler’s versions are NOT adjustable (cheaper) and that is why we are having these issues. This issue has been mentioned for most Jeep vehicles, including Grand Cherokee and Wrangler. I assume the terminal/post connection is loosened from offroading, so if you wheel a lot, be sure to keep an eye on it.

What to do if your Jeep instrument is off?

If all the modules are unplugged and the BUS voltage is still off, separate the connector near the instrument cluster to test the BUS voltage straight out of the printed circuit board. If the voltage returns to normal, there’s a problem with the wiring harness.

The cluster has stopped working again too. I decided to hook my OBD2 scanner up figuring there was probably a code and I pulled the following: P1686, P1694, P1698. All of them have to do with the PCM not communicating with the instrument cluster.

How to reset your Jeep engine control module?

3- Once the time has passed you should now turn the headlights “on” and “off” twice to drain the Engine Control Module from any remaining power. 4- Now plug back in the negative terminal and your Jeep ECM should now be reset. To finish off this post , here are a couple of things you should keep in mind.

Why is the PCM on my Jeep Cherokee not working?

I did notice that I have a wire (white with double black trace) that is cut, but after pulling the entire harness out I don’t see another end of that wire anywhere. According tothe All Data the white w/ double black trace and the purple with brown trace wires are communication wires that go back to the PCM.

Why is the CPS on my Jeep Cherokee not working?

According tothe All Data the white w/ double black trace and the purple with brown trace wires are communication wires that go back to the PCM. Again, another reason why I don’t think that the CPS is bad.

How to diagnose a malfunctioning Jeep instrument?

Put the key in the unlock position, the next position up from lock. (Lock is where you can remove the key.) 2. Depress and hold the trip reset button and turn the key to the on position, but do not start the engine. 3. Release the trip reset button and the tests should start.

What to do if your instrument cluster is not working?

If the instrument cluster doesn’t work, first determine which gauges don’t operate or if the whole cluster is down. I like to start testing with the printed circuit board self test. Check your manual for the proper procedure, as they may vary somewhat. 1. Put the key in the unlock position, the next position up from lock.

Why does my XJ instrument cluster stop working?

I have a 1999 XJ – and the instrument cluster occassionaly stops working — with mine, if you push on it towards the bottom (nearest the odo reset) it will reseat and continue working for months. This is the second instrument cluster – I replaced the original due to the same issue you are experiencing with a used cluster from eBay $35

How can I tell if my instrument cluster is defective?

If any of the gauges don’t actuate, then the instrument cluster is defective. If all the gauges appear to work normally with the self-test, move on to the BUS operation from the data link connector (DLC) under the dash. Check for the 2.5 volts on each wire.

Why are all the lights on my Jeep?

I parked the Jeep, turned it off and drove off after the gym and they never went back on again…but it’s still a concern. Is there any chance this could have happened due to the Sun throwing a major solar flare a few days ago?

What kind of Lights does a Jeep Grand Cherokee have?

All the lights (Check engine, transmission, abs, auto traction, etc, etc, etc) in my 2006 Jeep Grand Cherokee 4.7 Laredo’s instrument panel suddenly went on and off twice while driving (First time ever)…. And then the auto traction light as well as the ESP/BAS lights stayed on…

Why are my power windows not working on my Jeep Grand Cherokee?

While some other SUVs were manufactured with body-on-frame construction, the Jeep Grand Cherokee has always used a unibody chassis. Why won’t my power Windows work? I have a 1999 jeep grand Cherokee with the v8 engine and none of my Windows will go up or down.

Why does my Jeep Grand Cherokee sunroof not work?

The power locks on the drivers side doesn’t work but the power locks on the passengers side does work. My sunroof works also. Can someone please give me some helpful advice on what’s wrong and how to fix it.

Where is the fuse panel on a Jeep Grand Cherokee?

If the fuse blows again, have the vehicle inspected at a qualified service center. The interior fuse panel is on the lower instrument panel just to the left of the steering column. A label is stamped on the fuse panel cover to identify each fuse for ease of replacement.

Is there a problem with my Jeep garage door?

After some searching on the internet i found out that this problem happened already with quite some other WJ’s. Most of the time the black ground wire in the rubber boot between the door and the body breaks. Sometimes the orange wire breaks.

What causes no start on a jeep 4.0L?

Updated: 29 June 2019. Article Id: 420. A no start condition, on your 4.0L Jeep, is usually caused by a lack of fuel, or a lack of spark, or a lack of air (generally engine compression).

Why does my Dodge truck have no gauges?

Fortunately when I finally broke down out of utter frustration and took it to the dealer to have it repaired the first time it didn’t cost me an arm. $108 later the service guy said it was a loose wire connection in the PDC.

Is there a way to fix no bus no gauges?

No Way Not three times with it working fine for months in between. Cut to the chase. The Connector to the PCM wiring harness at the PDC was loose! Its the one that has a bolt in the middle of a square white connector. As I started to unscrewed it I noticed that the bolt was not tight. Ah ha!

What kind of bus does a Jeep Wrangler use?

The same two-wire CCD BUS that Chrysler has been using for years on its cars is now being used on Jeeps and trucks, giving today’s Jeep Wrangler a new level of sophistication. On these vehicles, the BUS bias voltage is produced by the printed circuit board or instrument cluster.

Is there a problem with my 2000 Jeep Grand Cherokee?

No one has added a helpful site for this 2000 Grand Cherokee problem yet. Be the first! Read reviews of repair shops in your area. Enter your zip code: Search CarComplaints.com for these popular complaint phrases…

What kind of gauges should I use on my 1999 XJ?

Lol I’m thinking may just go with all aftermarket gauges , speedo and tach…..trace out the indicator lights and do it custom….any thoughts on gauges? I have a 1999 XJ – and the instrument cluster occassionaly stops working — with mine, if you push on it towards the bottom (nearest the odo reset) it will reseat and continue working for months.

What do you need to know about YJ Wrangler dash panels?

YJ Wrangler dash panel parts are vehicle specific, so make certain you have the right part by talking with Jeep experts at 4WD. Components such as window defroster switches for Jeep and YJ Wrangler gauge clusters improve the appearance of the passenger cabin and upgrade functionality with new, premium parts.

Can a YJ dash pad be replaced at any time?

You can make small changes here and there, eventually getting things perfect, or you can do a complete makeover all at once. It’s your choice. A YJ dash replacement allows you to get the panels, switches, gauges and lights to your liking. The same is true of the YJ dash pad replacement.

What are the best parts for a YJ Wrangler?

Components such as window defroster switches for Jeep and YJ Wrangler gauge clusters improve the appearance of the passenger cabin and upgrade functionality with new, premium parts. Choose from quality brands, including Omix-ADA, Crown Automotive and Jeep for dash parts and hardware that are built to last.

What should my battery gauge be at with engine off?

The battery is putting out plenty of volts on it’s own with engine off. Before the light comes on and the gauge falls to 0, my battery gauge hovers at 12; meaning, the needle will move to just before or just after the 12V hash line intermittently

When does the check gauge light come on?

The Check Gauges light will only come on after it’s hit third gear and has been running in it for a least 10 seconds. I tested this for about 5 minutes riding around my neighborhood in 1st and 2nd trying to keep it under 3rd. Once I hit the main streets, the light came on within 10-15 seconds. I tried this twice.

Why does my Jeep Grand Cherokee fuel Gage stop working?

Jeep Grand Cherokee Questions – fuel gage stops working, then starts working agter time. why is this h… – CarGurus fuel gage stops working, then starts working agter time. why is this happening?

How can I tell if my Jeep Grand Cherokee is shifting?

Turn ignition key ON and OFF three times, finally leaving the key in the ON position. Leave the Overdrive Off Switch in the normal overdrive (ON) position. Immediately begin counting the number of flashes displayed by the Overdrive Off Switch indicator lamp. There will be two sets of flashes, separated by a pause.

Is there a problem with my Jeep Grand Cherokee?

Very often, this will solve the problem. But Jeep Grand Cherokees seem especially prone to more serious transmission problems, and some owners are quite vexed at their inability to determine the causes.

What should I do if my gas gauge is not working?

Note that some self-test steps may stop the gas gauge at 1/4, 1/2, and 3/4, as well. Fuel sender test. The fuel sender test should be conducted when the tank is lower than HALF, to prevent fuel splashing. Start by making sure the plug is clean, dry, and free of corrosion. Make sure the pins are straight and that the connector is fully seated.

What happens when the speedometer on a Jeep Grand Cherokee stops working?

One of the most inconvenient things that can happen to your Grand Cherokee is when the speedometer stops working. You don’t really realize how much you look at the thing until it’s just always sitting at 0 MPH while driving down the road.

What to do if your speedometer is not working?

Instrument panel first. If your Jeep Grand Cherokee’s speedometer is not working, the first place to go would be to check the service engine soon light (if applicable). Now, take it out and see if the cruise control still works. If it does, that’s a pretty good indication that the vehicle speed sensor is just fine.

What kind of speedometer does an amc20 have?

AMC20 with G2 1 piece chromos trussed, Dana 30 with G2 chromos and 760x ujoints and MM Stainless Hubs, Geared 4.56. Tom Woods shafts, Metal cloaks, Caged, 37″ Toyo MTs.

What causes the check gauges light to come on?

If any of your gauges reads zero, the check gauges light will come on. Sometimes even if the fuel gauge gets too low, it will trigger the light. It may be the connection at the sending unit. It may have become loose so wiggle it and make sure it is securely connected to the sending unit.

Why did the check gauges light come on?

Usually when the Check Gauges light illuminates it is due to one of the gauges going out of range, such as your electrical system, low engine oil or other type of fluids being monitored through the gauges.

What does “check gauges” mean?

1. To measure the dimensions, capacity, proportions, or amount of (something), especially by means of a gauge: gauged the thickness of the metal part. 2. To evaluate or estimate: gauge a person’s interest.

What does check Gages mean?

Check gages means that one of the gages is reading an abnormal reading, like hot engine oil pressure issues, charging system voltage, pay attention next time it happens to the readings on the gages for something out of the normal.

What to do if your YouTube gauges are not working?

Easy fix. How to reset. – YouTube Gauges not working? Instrument cluster not working ? Easy fix. How to reset. If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer.

Why does my car not start when I Turn on the key?

This feature is not available right now. Please try again later. One possible reason your car wont start is a bad connection. This is one of those things that is often over looked until after the battery or starter or alternator have been replaced or all of the above. if this happens to you check your battery connections. Loading…

What to do if your Jeep Wrangler won’t start?

Turn the key enough to move from park to neutral. Hold your foot on the brake while turning the key to start the ignition. If your Jeep won’t start and you simply hear one click, then you could have a faulty starter motor. Again, using a voltmeter with a load function, make sure all your voltages are all correct.

How can I tell if my Jeep Wrangler battery is dead?

Well, the most effective is to hook up a voltmeter and take a reading under the load setting. The first starting point when diagnosing a dead battery is to verify your battery has the correct voltage. Incorrect or low power to the starter will not start your Jeep. Batteries use CCA (Cold Cranking Amps) to measure starting power.

When to replace ignition switch on Jeep Wrangler?

DEALERS WILL REPLACE THE IGNITION SWITCH WITH A REDESIGNED SWITCH. OWNER NOTIFICATION BEGAN APRIL 8, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.

Why does my Jeep Wrangler not start up?

However, if your fuel gauge shows that the tank is full, there may be a problem with signal transmission. Then you should just be looking into the tank. Or, the fuel filter is clogged so that fuel cannot be pumped to the engine properly.

How to troubleshoot a no start Jeep 4.0L?

More specifically, this means that troubleshooting the problem requires that you check and confirm that: All 6 cylinders are getting spark (with a spark tester). That the fuel pump is creating enough fuel pressure. And if necessary, check the engine’s health with a compression test. I’ll go into more specific details in the following headings: 1.)

What should the battery reading be on a Jeep Wrangler?

Batteries use CCA (Cold Cranking Amps) to measure starting power. Be aware that your battery could have power, however, when under load, the cranking amps are not powerful enough to get the starter to crank the engine. A good fully charged battery should read over 12.6 volts. If the battery reads 12.45 volts or less, it is low.

Why does my speedometer not work when I change the battery?

Those number should be facing down when installed in the tail cone, if they aren’t the gears won’t mesh and the speedo won’t work.. Lifted,intake. Superchip. Still trying to.trace grounds. Just the way it went out when i changed the terminals on the battery makes it sound like.it could be ground issue. mudbug85603 likes this. Welcome to the forum.

How much does it cost to repair a speedometer?

He said that the speedometer itself went bad and needed to be rebuilt (they don’t make replacements anymore) with a total repair cost of about $500. Welcome @corderm .

Why is my speedometer not working on my Jeep?

The ECU is programmed with your Grand Cherokee’s gear ratios and stock tire height. It combines this data to send the speed reading to the instrument cluster. The causes of a bad speedometer will typically be found in these four things:

What’s the problem with my 1998 Jeep Cherokee?

No one has added a helpful site for this 1998 Cherokee problem yet. Be the first! Read reviews of repair shops in your area. Enter your zip code: After the dealer fixed the problem for the recall on the airbag module problem, the airbag light stays on and gauges and odometer work intermittently. The gauges are not working 80% of the time.

Why are the mileage gauges on my Jeep Cherokee not working?

Every once in a while when driving the airbag light turns on and the gauges do not work. When this happens the mileage does not record. We found out that by hitting the horn lightly two times the gauges will work again. Not a big deal, but annoying. The gauges on the dashboard sometimes don’t work.

Why is my oil pressure reading so low?

Oil Pressure Gauge Reading Too Low. When your engine is idle or when you’ve just started your car, the oil pressure gauge will have a low reading. When the engine starts running and heating up or when you’re already cruising on the freeway, your gauge’s reading should increase.

Can a broken oil pressure sensor be a problem?

Often, the oil pressure sensor and the oil pressure gauge are the first things to break. While a broken oil pressure gauge is not a threat to your vehicle, it is too important a tool for you to lose.

Why is my oil pressure gauge not working?

Some common indicators that the oil pressure gauge is not working correctly include: Oil pressure gauge not working: The causes for this range from a faulty gauge to the need for an oil change. Oil pressure gauge reading too low, generally below 15 to 20 PSI while idling.

Why does the oil pressure say 0 on my Jeep?

If the noise is still the same as before, its probably the oil pressure sending unit which is at fault. It happens once in a while on my jeep that when i start it up, that the pressure stays at 0. Most of the time when i shutt it of and start it again, its normal again.

How can you tell if your oil pressure is too low?

Oil pressure gauge reading too low, generally below 15 to 20 PSI while idling. Cold weather can also make the oil pressure read low until the oil pump has had a chance to deliver the oil to the engine. Oil pressure gauge reading too high, or over 80 PSI while driving, especially at higher RPMs.

Why does my Jeep Wrangler keep running out of fuel?

Another common reason that your Wrangler may be starving for fuel is a bad fuel pump. The fuel pump is responsible for sending highly pressurized fuel to the fuel rails. The engine can die if the fuel pressure is not high enough to properly atomize the gasoline properly.

What causes random stalling on a Jeep Wrangler?

There are 2x bolts sticking up presses into the harness creating random shorts and misses. No code will appear either. Signs of a failing Fuel pump are, but not limited to: A weak fuel pump with low pressure results in your engine not getting the correct fuel to air mixture it needs to power the vehicle.

Why does my Jeep Wrangler shut down while driving?

If your Jeep Wrangler is shutting down while driving, it’s a real safety hazard. Vehicles are a lot harder to control without power brakes or steering. Directly below is a list of the most common reasons why your Wrangler would randomly die while driving. It may help you in your diagnosis.

Navigation