What size wiper blades do I need for a 2008 Mazda 3?
Mazda 3 Wiper Size Chart
| Year | Driver Side | Passenger Side |
|---|---|---|
| 2010 | 24″ | 19″ |
| 2009 | 21″ | 19″ |
| 2008 | 21″ | 19″ |
| 2007 | 21″ | 19″ |
What size windshield wipers do I need for a Mazda 3?
Your 2018 Mazda3 is going to need to use a 24 inch driver’s side blade and a 18 inch passenger blade.
How do you put windshield wipers on a Mazda 3?
Move the wipers to the service positions using the following procedure.
- Switch the ignition ON.
- Switch the ignition OFF.
- Press up the wiper switch to the MIST position 2 times within 30 seconds after switching the ignition OFF. When the procedure is completed, the wipers operate and they stop at the service positions.
How do you replace the windshield wiper blade on a Mazda 3?
Pull down the blade rubber and slide it out of blade holder. Remove the metal stiffeners from each blade rubber and install them in the new blade. Do not bend or discard the stiff eners. You need to use them again. If the metal stiff eners are switched, the blade’s wiping effi ciency could be reduced.
How to remove the front bumper from a Mazda 3?
When disengaging the front bumper from the front bumper slider, the front bumper could fall and be damaged. Support the front bumper so that it does not fall. 2. Attach the front bumper to the body. 3. Press the front bumper connecting area in the direction of the arrow shown in the figure to engage with the front bumper slider. 1.
Where can I get new windshield wiper blades for my car?
EZwipers is the easiest and quickest way to find replacement windshield wiper blades for your car or truck. All wipers are 100% guaranteed to fit and are available for most cars, including Ford, Chevrolet, Toyota, Nissan, Honda, Dodge, Hyundai, Volkswagen, Mazda, and Subaru.
Which is the correct way to lower the wiper arms?
When lowering the wiper arms, slowly lower the wiper arm from the passenger’s side first while supporting it with your hand. Forcefully lowering the wiper arms could damage the wiper arm and blade, and may scratch or crack the windshield.
How do you remove the wiper motor from a Mazda 3?
1. Slide the windshield wiper motor in the direction of the left front fender and pull it out from between the windshield and the cowl panel. 2. Be careful when removing the windshield wiper motor so that it does not strike the windshield. If the windshield wiper motor hits the windshield, it could cause damage to the windshield.
What to do if you remove the front wiper motor?
Center cowl grille No1, No2 3. Stick masking tape on the figure. If the front wiper motor is removed without affixing protective tape to the windshield, the motor may contact the windshield and damage it. Always affix protective tape along the edge of the windshield when removing the front wiper motor.
What happens when you change the windshield wiper blade?
If the metal stiff eners are switched, the blade’s wiping effi ciency could be reduced. So do not use the driver’s side metal stiff eners on the passenger’s side, or vice versa. Be sure to reinstall the metal stiff eners in the new blade rubber so that the curve is the same as it was in the old blade rubber
Which is the correct way to raise the windshield wiper?
NOTE When raising both windshield wiper arms, raise the driver’s side wiper arm first. When lowering the wiper arms, slowly lower the wiper arm from the passenger’s side first while supporting it with your hand. Forcefully lowering the wiper arms could damage the wiper arm and blade, and may scratch or crack the windshield.