What is the serial number on a 2005 International 4300?
I have a 2005 International 4300 with code 534 fmi 4 sid 221 and code 525 fmi 6 sid 254. I have power at the fuses in Have truck repair questions?
What is the oil pressure on an International 7400?
2007 international 7400, crank no start, with codes sid254 fmi6 and a sid221 fmi4. Has 900lbs of injection control oil pressure when cranking. … read more
What are the fuse pins on an international 4300?
You need to check the 5 a fuse in the fuse box, also need to check the idm connector (white one) pins 1,2,3,22,26 for ground. Pins 4,23,24,25 for main power.
What are the codes on a 2007 International 4300 DT466?
HAVE CODES SID 254 I HAVE A 2007 INTERNATIONAL 4300 DT466. HAVE CODES SID 254 FMI 6 AND 221 FMI 4. IHAVE TESTED ALL THE WIRING FROM … read more
What are the trouble codes for International trucks?
International Trucks Diagnostics Trouble Codes (DTCs) for Model: 3200, 4100, 4300, 4400, 7300, 7400, 7500, 7600, 7700, 8500, 8600, BE 200, CE Bus, CXT, DuraStar, LoneStar, MXT, ProStar, RXT, TranStar, WorkStar
What is fault code 525 FMI 6 injector dirver?
I have a truck with fault codes 525 fmi 6 Injector Dirver Circuit Fault *m* and 534 fmi 4 IDM- Relay Voltage Low. It doesnt show symptoms of a fault but it has the engine light on. It turns on and runs fine. I have checked the voltage to the IDM relay and its getting 12.4.
Why does my IDM say 525 and 534?
There is a idm relay in the fuse box that could be bad or have a bad connection, but when you test your pins at the idm that will tell you where to go. Usually, when the 525 code is along with 534 for idm you almost always have a low/no voltage going to the idm.
Is the DT466 IDM relay circuit low voltage?
2007 International 4300 dt466 IDM Relay circuit low voltage, no start. fuse 25amp at battery. 3rd visit for this issue. Hello I have a 2008 international 4300 ***************** With the non max force dt 466 . I am getting codes for IDM 534 idm relay voltage low 525 idm … read more
What’s the oil pressure on a 2006 International 4300?
SPN175 ENGINE OIL TEMP. SPN 102 BOOST PRESSURE. FMI= 4 VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE. SPN 100 ENGINE OIL PRESSURE. FMI= 3 VOLTAGE ABOVE NORMAL OR SHORTED TO HIGH SOURCE. SPN105 INTAKE MANIFOLD TEMP. FMI= 4 VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE. SPN 94 FUEL DELIVERY PRESSURE.
Why does my international 4300 engine not start?
Replaced injector, put new orings on hipop. It will not start. Runs on ether but dies as soon as ether stops. Replaced both batteries. Checked fuses by batteries. All good. We pulled the ipr and bench tested it. It was working. Scanner says 8 engine codes. They are: FMI=4 VOLTAGE BELOW NORMAL OR SHORTED TO LOW SOURCE.
What is the active code of a 2005 FMI 7?
I Have a 2005 international 4300. Active code of 368 FMI 7, EGR driver mod./ECM2 comm. fault. The engine starts and We use cookies to give you the best possible experience on our website. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them.
What is the active code of 368 FMI 7?
Active code of 368 FMI 7, EGR driver mod./ECM2 comm. fault. The engine starts and runs, no power. What is the diag. procedure for this? Where is the EGR module located? Submitted: 7 years ago. Category: Medium and Heavy Trucks Andy : Hi there ! My name is XXXXX XXXXX I would like to try and help if I can ! 6H159844. New info.
Can you turn off the throttle on a 2004 IH 4300?
Turn the key off and everything is ok. 2004 IH 4300 1HTMMAAN24H609204 4H609204 I erased them but the twin to this truck had these codes with a similar problem. PID 91 FMI 7, PID 102 FMI 2, SID 230 FMI 2 When code 133 is active the amber ENGINE lamp is illuminated and the odometer displays the message WARN ENG.
Can a 2007 IH 4300 run in sub zero temps?
The place I work at has a 2007 IH 4300 with a DT466. The past few days have been sub zero temps here. It ran fine the beginning of the week but yesterday it wouldn’t start. We pushed it in the garage and let in warm up over night. We also put the batteries on charge since they were pretty weak.
What are the fault codes for International trucks?
International Trucks Fault Codes List (DTCs) for Model: 3200, 4100, 4300, 4400, 7300, 7400, 7500, 7600, 7700, 8500, 8600, BE 200, CE Bus, CXT, DuraStar, LoneStar, MXT, ProStar, RXT, TranStar, WorkStar. See also: International Trucks Service Repair Manuals PDF