How to remove front passenger axle shaft on Toyota Sienna?
Been lurking for a while and finally hit a big enough problem without an obvious solution already available here via search. I am trying to remove the passenger (RH) side axle shaft on a 2wd 2004 Sienna. I have the axle nut off, the bolt out of the bearing housing, and the C-Clip off of the shaft.
How big is the AWD coupling on a Toyota Sienna?
I measured it to be 120mm OD, 95mm ID, and 16.95 mm thick. This is supposed to be Toyota part 90363-95007, which I got online for $31.93. I also ordered the smaller bearing 90363-65004 and the dust deflector 41252-44010, and an oil seal 90310-54001. All together, the order was $76.90 with shipping in the USA.
Where to place the coupler on a Toyota Sienna?
The coupler should be positioned with the input flange facing up, and some blocks placed under it to support the edge of the housing, but let the assembly move downward. I also placed another block of wood in the middle to limit how far the assembly could fall, so the wires didn’t get broken. Pay attention to those wires!!
How much does it cost to repair a Toyota Sienna?
This is supposed to be Toyota part 90363-95007, which I got online for $31.93. I also ordered the smaller bearing 90363-65004 and the dust deflector 41252-44010, and an oil seal 90310-54001. All together, the order was $76.90 with shipping in the USA.
How do you reassemble a Toyota Sienna?
Reassemble on-vehicle to have a new outer joint on the original axle. I read that this is what Toyota mechanics do to save time. 2) Use a reciprocating saw (such as Sawzall) to cut the old axle between the trans and the bracket.
What to do if a bearing is stuck on a Sienna?
Is the carrier bearing is still stuck at removal, be prepared to cut the axle (torch or grinder) between the transmission and bearing, and using a sledgehammer to drive out the remaining axle. My experience is for a 2004 Sienna (3.3L motor, I think yours is 3.5L motor).
How do you remove an axle from a Toyota?
Take the ring off, and you can use tap the axle from the other side of the bracket outward towards the passenger side. No extra work required. You got lucky. It’s common to have to cut the axle in two spots to get the carrier bracket off and then, with the carrier bracket in a vice, a 5lb sledge to get the bearing out of the bracket.
How much does it cost to replace an axle on a Toyota Sienna?
Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM. Toyota Sienna CV Axle / Shaft Assembly Replacement costs $376 on average.
Can a front axle be removed from a Toyota?
Yes, I’ve removed the axle nut, the stabilizer link, the speed sensor, the tie rod end, the control arm sub-assembly, separated the front axle from the knuckle, removed the drive shaft bearing bracket hole snap ring, and removed the bolt from the drive shaft bearing bracket.
How to replace front drive axle or drive shaft left side?
How to replace front drive axle or drive shaft LEFT side Toyota Corolla. Years 1995 to 2012 – YouTube If playback doesn’t begin shortly, try restarting your device.
Is there a safety test on a 2003 Toyota Sienna?
The 2003 Toyota Sienna has not been tested. Like what you see? Find the best deal on a Toyota Sienna today. There are for sale near you. Certified child passenger safety technicians conduct hands-on tests of a car’s Latch system and check the vehicle’s ability to accommodate different types of car seats.
What’s the problem with my 1998 Toyota Sienna?
Dry rot I guess. The parts I’m speaking of so far, have been, both inside door handles, the small plastic piece that covers the air conditioner on button, the passenger side mirror cover, broke off about halfway down, while going through a car wash, There The plastic handle in the back passenger side seat that’s used to recline, has stripped out.
Why is there no oil in my Toyota Sienna?
As a result, oil leaks out of the hose and, if not caught in time, the engine will have no oil left and may seize. Many Sienna owners successfully resolve this issue by replacing it with an OEM metal cooler pipe (Part No. 15767-31020 ).
Where is the snap ring on a Toyota?
I took off the snap ring first with a pair of pliers, from under the car. The snap ring is found at the bracket everyone is referring to with 3 bolts. Take the ring off, and you can use tap the axle from the other side of the bracket outward towards the passenger side.
Are there any recalls on the 2004 Toyota Sienna?
Based on information received from our latest subscriber survey, our reliability history charts give you a rundown on how used vehicles are holding up in 17 potential trouble spots, ranging from the engine, transmission, and brakes to power equipment and the electrical system. The 2004 Toyota Sienna has been recalled 10 times by NHTSA. View Recalls
What kind of problems does a Toyota Sienna have?
Shocks or struts, ball joints, tie rods, wheel bearings, alignment, steering linkage (includes rack and pinion), power steering (pumps and hoses, leaks), wheel balance, springs or torsion bars, bushings, electronic or air suspension. “I’ve had to many problems with alignment.
How old is the Toyota Sienna struts?
My Sienna is 13 years old and has over 200,000 miles on it. It was due time for those struts to be replaced. When they replaced the struts, they also replaced all the adjoining parts. I would say that the struts were well overdue for replacement and I would call this more a maintenance issue than a failure in product”
How much does it cost to replace a CV axle on a Sienna?
Upfront and transparent pricing. Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM. Toyota Sienna CV Axle / Shaft Assembly Replacement costs $376 on average. What are CV Axles and how do they work?
https://www.youtube.com/watch?v=zlo_LlwE-1g
How do you take an axle shaft out of a car?
Wiggle and twist the steering knuckle free from the strut. When the two have separated, the axle shaft should have slid partially out. Pull the shaft out with your hands. Removal of this shield will allow pry bar access to the “ears” (pry bar leverage points) of the axle’s inner bearing cup.
How to install front disc brake on Toyota Sienna?
INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH (a) Install the front disc brake caliper assembly LH with the 2 bolts to the steering knuckle LH. 13. INSTALL SPEED SENSOR FRONT LH (See page DS- 18) 14. INSTALL FRONT AXLE HUB LH NUT (a) Using a socket wrench (30 mm), install a new axle hub LH nut.
Where is the support bracket on a Toyota Sienna?
My experience is for a 2004 Sienna (3.3L motor, I think yours is 3.5L motor). On my van, the support bearing was not pressed into the bracket but it may as well have been. There is a Clip (like a snap-ring) that is intended to retain the bearing into the bracket.
Can a tie rod be removed from a transmission shaft?
Tie Rod from the knuckle You may have done all those things but didn’t make mention of those. With all that removed you’re supposed to separate the the shaft from the bearing with only a plastic hammer, then attach a slide hammer to the end going into the transmission to fully remove it.