How to program the keyless entry on a Pontiac G6?

Put your key in the ignition and hold the “Lock” button on the driver’s car door. Turn the G6 key in your ignition from “On” to “Off” while holding the “Lock” button, and do two more cycles of “On” and “Off” in quick succession. Release the “Lock” switch on your door and press and hold the “Lock” button on your keyless remote for 10 to 15 seconds.

Why is my Remote key not working on my Grand Prix?

I own a 2007 Pontiac Grand Prix. My remote key isn’t working to unlock my doors sometimes, but it always opens my trunk easily when I press it. Sometimes I have to press the unlock button over and over to open the doors, sometimes it never works, or sometimes it works the first time.

How do you lock your door on a G6?

Release the “Lock” switch on your door and press and hold the “Lock” button on your keyless remote for 10 to 15 seconds. Remove the key from the ignition of your G6, and test the programming. Matthew Fortuna is a full-time freelance writer with a journalism degree from Wayne State University, living in the Detroit metropolitan area.

Why is my Remote key not working to unlock my doors?

My remote key isn’t working to unlock my doors sometimes, but it always opens my trunk easily when I press it. Sometimes I have to press the unlock button over and over to open the doors, sometimes it never works, or sometimes it works the first time. I don’t know what to do to fix it. It sounds to me like the fob contacts are giving up the ghost.

How to program a new car key fob?

Refer to Electronic Diagnosis in Body and Chassis. Turn the ignition lock cylinder to the ACC position. Turn the ignition lock cylinder OFF, then back to ACC within 1 second. Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode.

When do I hear the chime on my key fob?

If you do not hear a chime, start again at step 1. After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming. Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.

How to program a replacement key fob for a 2007 Pontiac G6?

I was just curious if anybody here has experience in reprogramming a key fob for a 2007 Pontiac G6. The car seems to have a Vehicle Theft Protection system, because it engages when I lock up the car, but it doesn’t trigger when I mess with the door handle, not sure if thats important but I’m throwing it in there.

Is there a remote keyless entry on the Pontiac G6?

Introduced in 2005, the Pontiac G6 became one of Pontiac’s top-selling cars. The car often comes standard with a keyless-entry remote program, and the program allows remote access to the doors, trunk, panic button and car starter.

How to Program the Keyless Entry on a Pontiac G6. Turn the G6 key in your ignition from “On” to “Off” while holding the “Lock” button, and do two more cycles of “On” and “Off” in quick succession. Release the “Lock” switch on your door and press and hold the “Lock” button on your keyless remote for 10 to 15 seconds.

What does mall stand for in Pontiac G6?

Pontiac called it MALL/PGM in the grand prix/sunfire/sunbird, etc… in the G6 apparently changed names… I found online a guy claims the MALL/PGM stands for “Multifunction Alarm Lock and Lighting” and PGM = “Programming”… that said in our cars, as you found no such label…

When did the GM Keyless remotes come out?

There are three broad categories when it comes to GM keyless remotes: pre-2007, 2007–10 with VIC, and 2007 – 10 without VIC. If your car is a GM post-2010 model, you should contact your nearest car care professional. After 2011, most GM models have already synced transmitters that come with the car when you buy it.

What’s the best way to program a GM remote?

Sit comfortably in the driver’s seat, and make sure that your transmitter is close enough to the steering wheel and internal locks. Pull on the internal handles of each door to make sure that they are closed tightly. Turn your key to the “Accessory Power” position.

Navigation