How to do the throttle body relearn procedure?
During this period the idle may be higher than normal. It should slowly drop as the engine heats up. Watch the engine temp gauge and note when it reaches operating temp. Then continue to let it idle for an additional 5 minutes. It will continue to adjust idle during this period.
What happens when you replace the throttle body?
If you replace the throttle body, the PCM won’t know and will continue to use the adaptive settings as if the carbon buildup is still in place. If you don’t do a relearn procedure, the PCM will “hunt” for a new baseline idle.
How to do throttle body re-Learn Chevy Malibu?
1) Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal. 2) After 3 minutes, turn the engine off and leave it off for 60- seconds. 3) Start the engine again and let it idle in park for 3 minutes one more time. During these run periods you may see a check engine light.
What is the throttle relearn procedure for a Takoma TRD?
Vehicle is a 2013 Takoma TRD/4.0 V6. That relearn procedure is the about the stupidest thing I’ve seen on here. I had to go to the post office this morning and tried something. I stopped part way to the PO (engine was warmed up), put the trans. into 1st and slowly let the clutch out – no throttle.
What is the idle relearn procedure?
- set the parking brake.
- turn off all accessories.
- Run the engine until it reaches normal operating temperature.
- Allow engine to idle for at least one minute.
- Turn the air conditioning on and allow the engine to idle for at least one minute.
- Release the parking brake.
Do I need a throttle body service?
There is no specific mileage requirements and some cars may never need this service. A throttle body usually gets dirty at higher mileage (after 60K-80K miles), mostly in cars that are often driven in stop-and-go city traffic or when oil changes are not done regularly.
Can the throttle position be high during idle?
Sometimes the throttle can also be stuck to a high idle position because of gunk and grime that gets either underneath it. Grime and sticky substances can also get inside the throttle cable and cause that to malfunction as well. I had a CB650 that actually had both of these issues.
What should I do after replacing my throttle body?
After replacing the throttle body to your engine, if the engine light was on and has a pending code, the code will go away. If the code was a hard permanent code, then the ECM (computer) would need a hard reset. Remove the negative battery cable (-) and keep it off for about 13 minutes, then hook up the battery cable and make sure it is tight.
How to reset throttle body calibration [ step by step guide ]?
Make sure that the accelerator pedal is fully released. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds.
When to do a Ford throttle body relearn?
Make and Model > Ford, Lincoln, Mercury > Aviator > Ford throttle body relearn… If you’ve replaced your Ford electronic throttle body or you’ve disconnected the battery, you must do a Ford throttle body relearn to establish a new baseline idle.
What to do if your throttle body goes out?
If the code was a hard permanent code, then the ECM (computer) would need a hard reset. Remove the negative battery cable (-) and keep it off for about 13 minutes, then hook up the battery cable and make sure it is tight. The engine light will go out and clear all codes as it goes into a learn cycle.
How to relearn throttle on a new battery?
Throttle relearn procedure/New battery/Won’t Idle or Run Step 1: Turn the key to the ON position but do not start. Step 2: Press the accelerator pedal ALL THE WAY to the floor and hold it for 40 seconds. Step 3: Release the accelerator pedal ALL THE WAY and count for 35 seconds. Step 4: Press the
Make sure that the accelerator pedal is fully released. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds. Turn ignition switch “ON” and wait at least 2 seconds. Turn ignition switch “OFF” wait at least 10 seconds.
What’s the best way to learn the throttle valve?
1) Turn the ignition key ON for at least 10 seconds and then OFF for at least 10 seconds. This procedure allows the ECM to automatically learn the throttle valve position. Alldatadiy.com and Eautorepair.net are professional-grade shop manuals—period.
How to clean and relearn Hyundai throttle body?
1. Remove the breather hose and air intake hose. 2. With ignition key off disconnect the ETC connector from the throttle body. 3. Remove the 4 ETC throttle body mounting bolts and then pull out the ETC throttle body away from the intake manifold.
Is there a way to reset the throttle body?
This method is almost foolproof as long as all ECU control parameters are within their normal ranges. Resetting The Throttle Body Calibration (this step is conditional) A Rough Idle or a SES can sometimes be caused by a change in the throttle body position sensor calibration.
During this period the idle may be higher than normal. It should slowly drop as the engine heats up. Watch the engine temp gauge and note when it reaches operating temp. Then continue to let it idle for an additional 5 minutes. It will continue to adjust idle during this period.
1) Start the engine and let it idle in park for 3 minutes. During that period the idle may be higher idle than normal. 2) After 3 minutes, turn the engine off and leave it off for 60- seconds. 3) Start the engine again and let it idle in park for 3 minutes one more time. During these run periods you may see a check engine light.
If you replace the throttle body, the PCM won’t know and will continue to use the adaptive settings as if the carbon buildup is still in place. If you don’t do a relearn procedure, the PCM will “hunt” for a new baseline idle.
How to relearn throttle body on Dodge Jeep Chrysler?
If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: i7KDtNapLAIzcuvk)
How to relearn high idle after throttle cleaning?
The idle will relearn if you put the vehicle in drive and allow the idle to come down with all accessories off for about two to three minutes. Then turn on your a/c with blower in high position for three minutes.
How does the ECM learn the new throttle position?
Perform the Throttle Learn Procedure. Refer to Throttle Learn. The engine control module (ECM) learns the idle position of the throttle plate to ensure the cor- rect idle. Anytime the throttle body is cleaned or replaced, the ECM must learn the new throttle position.
What happens when the throttle plate is cleaned?
Perform the Throttle Learn Procedure. Refer to Throttle Learn. The engine control module (ECM) learns the idle position of the throttle plate to ensure the cor- rect idle. Anytime the throttle body is cleaned or replaced, the ECM must learn the new throttle position. The idle may be unstable or a DTC may set if the throttle position is not learned.
How to re-learn Nissan electronic throttle body ( ETB )?
Turn ignition switch OFF and wait at least 10 seconds . ( 1:17) 4. Turn ignition switch ON and wait at least 2 seconds . ( 1:24) 5. Turn ignition switch OFF and wait at least 10 seconds ( 1:29) Throttle Valve, Closed Position Learn. 1. Make sure that accelerator pedal is fully released. ( 1:38) 2. Turn ignition switch ON. ( 1:39) 3.
How to do throttle body idle and volume relearn?
Turn the ignition switch off for at least 10 seconds. Again, turn the ignition on for at least 2 seconds. Turn the ignition off for at least 10 seconds. This action will inform the computer on the new release position of the accelerator pedal and the closed position. Now that this is done, we can move on to the next step.
How long does it take for GM throttle body to relearn?
If you don’t do a relearn procedure, the PCM will “hunt” for a new baseline idle. It will eventually learn it on its own, but it may take over a week of driving, during which time you will experience high and low idle speeds and possibly rough idle. 1) Start the engine and let it idle in park for 3 minutes.
What’s the throttle relearn procedure for a new battery?
Step 2: Press the accelerator pedal ALL THE WAY to the floor and hold it for 40 seconds. Step 3: Release the accelerator pedal ALL THE WAY and count for 35 seconds. Step 4: Press the accelerator pedal all the way to the floor and hold for 30 seconds. Step 5: Release the accelerator pedal and count for 25 seconds.
How is the gas pedal connected to the throttle body?
Many car makers including GM started installing fly by wire electronic throttle bodies. In those vehicles, the “gas” pedal isn’t connected to the throttle body by a cable. The pedal simply provides an electronic signal, telling the throttle body how much acceleration you’re requesting.