How to diagnose a Saturn ignition key or switch problem?
Locate the fuse for the starter in the fuse panel using the fuse diagram on the underside of the fuse panel cover. Remove the fuse using a fuse puller in the fuse box. Check the fuse to make sure that the metal strip inside the fuse is not broken or damaged in any way. If it is, replace the fuse with another fuse of the same amperage.
Where are the fuses on a Saturn Ion?
Saturn ION (2003 – 2004) – fuse box diagram Year of production: 2003, 2004 Instrument Panel Fuse Block Some fuses are in a fuse block on the driver’s side of the floor console. Saturn ION – fuse box – floor console Fuses Usage AIR BAG Air bags, Sensing and Diagnostic Module (SDM) ACCOMMODATION INTERFACE/ ONSTAR
Can a faulty ignition switch cause a car to not start?
There is a component inside the dash and linked to the ignition switch that sends a signal to the starter motor allowing the vehicle to start. If you are experiencing problems with your ignition key or switch, you may need a simple key reset or you could have a faulty ignition switch that needs to be replaced.
What kind of Fuse does a Saturn SL have?
Electrical components such as lights, heated seats and radios all have fuses in your 2000 Saturn SL 1.9L 4 Cyl.. This free video shows you how to replace a blown interior fuse on a 2000 Saturn SL 1.9L 4 Cyl. About Us Maintenance Parts & Tools Contact English SpanishFrench Search Home Saturn SL 2000 Fuse (Interior) / Replace
What do you need to know about the wiring on a Saturn?
These Saturn Wiring information / Aftermarket Autostart/Alarm Technical Wiring Diagrams are very useful, if not required, for the installation of alarms, autostart / alarms, remote starts, doorlock info and any other aftermarket installation that would require you to know the / Wire Information / Wiring Information of your Saturn
Where is the control arm assembly on a Saturn SL2?
Control Arm Assembly, Rear Lower Rearward Driver or Passenger Side… Control Arm with Ball Joint Assembly, Front Lower Passenger… Control Arm with Ball Joint Assembly, Front Lower Driver and…
Where is the return spring in the brake system?
While you’re at it, visually check all the flexi hoses in the braking system for signs of bulging or wear – if any show such signs, replace them all. The return spring is generally in the back of the master cylinder. If the M/C is working correctly, the brakes should, with the engine off, behave correctly, but be harder to push.
Where is the fuse on a Saturn ignition?
Open the fuse panel under the steering column by turning the knob on the fuse panel counterclockwise and pulling down on the cover. Locate the fuse for the starter in the fuse panel using the fuse diagram on the underside of the fuse panel cover. Remove the fuse using a fuse puller in the fuse box.
Why are the brakes not working on my Saab?
The brakes are not tough, the fluid is fine, the master cylinder was in excellent condition, the booster diaphragm was in one piece, and the hoses were all sound. The brake lines were also in good condition. Chalk it up to another Saab-related mystery. I’ve had a few of those lately and it makes me want to never have another Saab ever again.
What to do if you have ignition switch problem?
If you are experiencing problems with your ignition key or switch, you may need a simple key reset or you could have a faulty ignition switch that needs to be replaced. Open the fuse panel under the steering column by turning the knob on the fuse panel counterclockwise and pulling down on the cover.
What to do if your ignition key is broken?
Check the fuse to make sure that the metal strip inside the fuse is not broken or damaged in any way. If it is, replace the fuse with another fuse of the same amperage.
What should I do if my Saturn ignition is not working?
Turn the ignition key and try to start the engine. If the battery is known to be fully charged, the Saturn should start. If there is an error in the ignition switch, you will not hear the typical faint “click” when you initially turn the ignition key to the “III” position to crank the engine.
Where is the ignition switch on a Saturn?
The problem was due to the original ignition switch which is a $50 part from Saturn. The ignition switch is located on the back end of the ignition lock. The ignition switch sends a code that is generated in the ignition lock to the body control module (BCM). It is a part of the Passlock2 system on the 2004 Saturn.
Why does my Saturn car keep starting when I take the key out?
Saturn cars can suffer from ignition problems that you can potentially resolve with some time and detective work. The tumblers in a Saturn lock cylinder can wear out prematurely, causing the key to stick in the ignition or the engine to continue running after removal of the key. Replace the lock cylinder to solve the starting problem.
What causes the lock cylinder on a Saturn to wear out?
The tumblers in a Saturn lock cylinder can wear out prematurely, causing the key to stick in the ignition or the engine to continue running after removal of the key. Replace the lock cylinder to solve the starting problem.