How many torquing passes in a criss-cross torque sequence?
Torque bolts and nuts in a “CRISS-CROSS” sequence using a minimum of three torquing passes and the maximum bolt stress as defined. PASS 1 Torque Sequence: Torque to a maximum of 30% of the final torque value in accordance with the torque sequence.
What are the recommended torques for an assembly?
Bolt Tension Recommended Corresponding to Assembly 65% of Proof Load Torque kN Nm 3.17 1.9 5.54 4.4 8.97 8.9 12.7 15 23.1 37 36.6 73 53.2 128 72.8 203 98.8 316 121 436 155 620 191 840 222 1066 289 1561 354 2124 437 2884 515 3708 Page 3
Where can I find the latest torque specs?
Find the most up-to-date torque spec listings in electronic format. FelPro-Only.com is your convenient source for advanced sealing information. It’s the place to learn and share “tricks of the trade,” find proper diagnosis and installation instructions, and enjoy easy access to parts reference.
What are the torque specifications for a Cavalier?
Find out how to access AutoZone’s Torque Specifications Repair Guide for Cavalier, Sunfire 2001-2005.
How much torque does a LS engine have?
LS Engine Firing Order LS1 & LS6 Torque Specs Bolts or Engine Parts to Torque Amount to Torque or Turn (Degrees) to: Camshaft Retainer Bolts 18 lb ft Camshaft Sensor Bolt 18 lb ft Camshaft Sprocket Bolts 26 lb ft Connecting Rod Bolts – First Design (First Pass)
What are the torque specs on a Honda Civic?
This article applies to the Honda Civic (incl. Del Sol) (1992-2000). Tightening your bolts too much or not enough can cause a part to fail, and depending on the part, can put your life and the lives of the any passengers in danger. Most parts come with bolt-tightening torque specs, and your owner’s manual should have this information too.
Find the most up-to-date torque spec listings in electronic format. FelPro-Only.com is your convenient source for advanced sealing information. It’s the place to learn and share “tricks of the trade,” find proper diagnosis and installation instructions, and enjoy easy access to parts reference.
Where are the casting numbers on a LS engine?
Cylinder Head: Head casting numbers are found externally at the far right end of the head on the exhaust-port side. LS Engine Firing Order LS1 & LS6 Torque Specs Bolts or Engine Parts to Torque Amount to Torque or Turn (Degrees) to: Camshaft Retainer Bolts 18 lb ft Camshaft Sensor Bolt 18 lb ft Camshaft Sprocket Bolts 26 lb ft
Where do I get my torque specs from?
All specs are taken from Helms/GM documentation for a 2000 Model F-body. Special thanks to crackeregg for making these documents available in a digital format (saved me a lot of typing!).
Why do you need a torque sequence for a flange?
Flange joints require proper tightening to avoid the leak of the fluid from the joint. Bolt tightening sequence or torque sequence is defined in the torque tightening procedure. Most company has their Flange bolt torque tightening procedure that used during construction and operation of the plant.
What are the torque specifications for a magnum?
Find out how to access AutoZone’s Torque Specifications Repair Guide for 300, 300C & Magnum 2006-2008, Charger 2006-2008. Find out how to access AutoZone’s Torque Specifications Repair Guide for Cherokee, Grand Cherokee, 1999-2005. Find out how to access AutoZone’s Torque Specifications Repair Guide for Canyon, Colorado 2006-2007.
How to access AutoZone’s torque specifications repair guide?
Find out how to access AutoZone’s Torque Specifications Repair Guide for Grand Prix, Impala 2006-2008, Monte Carlo 2006-2007. Find out how to access AutoZone’s Torque Specifications Repair Guides.
Is there a torque specifications repair guide for Commander?
Find out how to access AutoZone’s Torque Specifications Repair Guide for Commander 2006-2007. Find out how to access AutoZone’s Torque Specifications Repair Guide for 300, 300C & Magnum 2006-2008, Charger 2006-2008. Find out how to access AutoZone’s Torque Specifications Repair Guide for Cherokee, Grand Cherokee, 1999-2005.
Torque bolts and nuts in a “CRISS-CROSS” sequence using a minimum of three torquing passes and the maximum bolt stress as defined. PASS 1 Torque Sequence: Torque to a maximum of 30% of the final torque value in accordance with the torque sequence.
When to specify a torque and tightening sequence?
Based on experience, if the bolts are in a circular pattern, a criss-cross tightening sequence would normally be specified. For non-circular bolt patterns, a spiral sequence starting at the middle would normally be specified (See Dia. B).
Do you need a cheat sheet for torque sequence?
From fixing a leaking push-rod tube, to slapping in some 94mm pistons and aftermarket heads, eventually the heads will be removed and need to be re-torqued. We’ve created this easy-to-use torque sequence cheat sheet. Save this to your phone, computer, or print it out for use in the shop!
Which is the correct sequence of torque passes for a flange?
Flange Bolt Torque Sequence. After the three basic torque passes are completed, repeat torquing the nuts at least once using the final torque in a “CRISS-CROSS” manner until no further rotation of the nut is observed. For easy handling, bolt numbering shall be done clockwise around the flange with the following sequence.