Where is the oil plug on a Harley Sportster?
Recommended Harley Engine Oils. The oil drain plug on the 2006 Sportster is located under the bike near the rear part of the frame. To drain the oil, loosen the small hose clamp that holds the drain plug in place, and work the plastic drain plug from the hose. I find that twisting the drain plug while pulling downward makes removal easy.
How do you change oil in a Sportster?
This will help the oil to drain completely. Remove the Sportster transmission oil drain plug using a 5/8 wrench and let the oil drain from the transmission. It is recommended that the motorcycle be straight and level and not leaning on the jiffy stand to ensure complete draining.
How much oil does a Harley Davidson Sportster use?
Screw the new filter onto the oil filter housing. Once the filter is seated, remove the funnel, and tighten the oil filter by hand approximately 1/2 to 3/4 of a turn. Do not use the oil filter wrench to tighten the filter. The Sportster uses 3.6 quarts of oil. It has been my experience that roughly 3 quarts actually drains from the engine.
Where to put primary lubricant in Sportster transmission?
Using a funnel, pour 32 ounces (one bottle) of Harley Davidson Transmission and Primary Chaincase Lubricant into the primary chain inspection hole. According to the Sportster maintenance book, the fluid level should not go above the bottom of the clutch diaphragm spring.
Recommended Harley Engine Oils. The oil drain plug on the 2006 Sportster is located under the bike near the rear part of the frame. To drain the oil, loosen the small hose clamp that holds the drain plug in place, and work the plastic drain plug from the hose. I find that twisting the drain plug while pulling downward makes removal easy.
How long does it take to change oil in a Harley Davidson Sportster?
Place a drain pan underneath the drain plug. Using a wrench, unscrew the transmission drain plug and remove it. Your drain plug may be 5/8″ or 3/4″ depending on the year. Allow all the oil to drain out of the transmission. It should take about five minutes.
What kind of oil does an 883 Sportster use?
Unlike its larger brethren, Harley-Davidson’s 883 Sportster employs a smaller motor that houses two separate fluids rather than three. The first, engine oil, is kept in an oil tank that facilitates an easy oil change.
How do you change transmission fluid in an 883 Sportster?
Add fresh transmission fluid into the primary through the derby cover hole. Continue to fill the primary until the transmission fluid level rises to the base of the round clutch assembly. Install the derby cover and its gasket onto the primary cover.
Place a drain pan underneath the drain plug. Using a wrench, unscrew the transmission drain plug and remove it. Your drain plug may be 5/8″ or 3/4″ depending on the year. Allow all the oil to drain out of the transmission. It should take about five minutes.
Where is the primary drain plug on a Harley Davidson?
Using a 5/32 Hex or Allen screwdriver, unscrew the two screws from the primary chain inspection cover. Remove the primary chain inspection cover from the transmission housing. The transmission drain plug is located on the underside of the transmission on the left side of the bike, near the kickstand bumper.
What to use to loosen oil filter on Sportster?
A traditional oil filter wrench can be used to loosen the filter on the Sportster’s Evo engine, but caution should be used not to damage any wiring or sensors located in close proximity to the filter. After the oil filter is loosened, I make a funnel by folding newspaper or cardboard into a “V” shape.
Where is the drain plug on a Harley Davidson Dyna?
Dyna and Touring models have their oil drain plugs under the transmission housing. Drain the engine oil into an oil pan. Replace the drain plug’s O-ring, then screw it into place after the oil has drained. Tighten the drain plug to 18 foot-pounds with a torque wrench.
Where is the oil plug on a Harley Road King?
Place your oil pan beneath the motor oil drain plug. The drain plug is located on the right side of the motor and to the rear of the frame. Remove the drain plug with a Torx socket and replace the plug’s o-ring.
Where is the oil drain plug on a softail motorcycle?
Unscrew the engine oil drain plug with a 5/8-inch socket and a socket wrench. On Softail models the engine oil drain plug is under the right side of the motorcycle’s frame, near the rear wheel. Dyna and Touring models have their oil drain plugs under the transmission housing. Drain the engine oil into an oil pan.
When to remove oil plugs on Harley Davidson?
It is of utmost importance to remove the engine oil and transmission oil fill plugs along with the primary derby cover; either before draining the oils or before the drain plugs are reinstalled. This will help to avoid confusion as to whether or not the oil has been replenished before attempting to start the motorcycle.