What is the GL1800 Fi fault indicator code?
GL1800 FI “Fault Indicator” Dashboard Codes If FI (Fault Indicator) light comes on pull over but DO NOT shut bike off. Put in neutral and put side stand down, RPM’s below 1500. This signals the ECM to send the error code to the FI light. Count the number of long and short flashes. This will give you the error code.
When does the fi light come on on a Honda Goldwing?
FI light appeared about 150 miles into a 250 mile ride in heavy rain. I notice that OD light comes on when I’m in neutral and the motor is running, too. Click to expand… Find the wires where the side stand switch is or used to be.
How do you find the error code on a Honda Goldwing?
Put in neutral and put side stand down, RPM’s below 1500. This signals the ECM to send the error code to the FI light. Count the number of long and short flashes. This will give you the error code. Also known as Malfunction Indicator Light (MIL) If you shut the bike off the error code is lost – sort of.
What does the Mil mean on a Honda Goldwing?
Also known as Malfunction Indicator Light (MIL) If you shut the bike off the error code is lost – sort of. It will be retained in the ECM but it is harder to get out. If the bike stops and the will not restart you can get the FI light to flash the error code by cranking the engine for 10 seconds.
GL1800 FI “Fault Indicator” Dashboard Codes If FI (Fault Indicator) light comes on pull over but DO NOT shut bike off. Put in neutral and put side stand down, RPM’s below 1500. This signals the ECM to send the error code to the FI light. Count the number of long and short flashes. This will give you the error code.
FI light appeared about 150 miles into a 250 mile ride in heavy rain. I notice that OD light comes on when I’m in neutral and the motor is running, too. Click to expand… Find the wires where the side stand switch is or used to be.
Put in neutral and put side stand down, RPM’s below 1500. This signals the ECM to send the error code to the FI light. Count the number of long and short flashes. This will give you the error code. Also known as Malfunction Indicator Light (MIL) If you shut the bike off the error code is lost – sort of.
What should I do if my Goldwing won’t start?
I would start by checking your starter switch, ignition, the starter relay and then the kickstand saftey switch. There is a few things that happen when you start the bike. One, you depress the starter switch, the headlight shuts off, the starter relay closes and the bike starts.
How do you get the error code on a Goldwing?
Put in neutral and put side stand down, RPM’s below 1500. This signals the ECM to send the error code to the FI light. Count the number of long and short flashes. This will give you the error code. If you shut the bike off the error code is lost – sort of. It will be retained in the ECM but it is harder to get out.
Why does my Goldwing radio not turn on?
If the low volume is FM only, it is internal to the radio.. in this case, another symptom is that the search/seek feature never locks on a station.. Typically this is a problem with a component on the board.. only place I know that works on them is Sierra Electronics in Troy Ohio, but others probably exist..
https://www.youtube.com/watch?v=W9TCNGoPSAg
Why do my turn signals stop flashing when I apply the brake?
Make sure you have the right bulbs in and check the wiring harness on your lights and take a look inside the light assembly for any short circuit. Also any addition like the third brake light and, like mayer said, a trailer light plug that is shortened can do it too. Good Luck to you Was this answer helpful?
Why do my blinkers stop blinking when I apply the brake?
All of these problems mentioned can be the result of a bad ground. When you operate both blinkers and brake lights and the blinkers stop blinking, it’s because the circuit is not good enough to operate both lights. Bad ground. Same with headlights and blinkers. Probably the same with fog lights.
What are the symptoms of a bad turn signal Flasher?
1. Turn signals or hazards do not function. The most common symptom of a bad or failing turn signal / hazard flasher is hazards or turn signal lights that do not function. If the flasher breaks or has any internal issues it can cause the lights to malfunction, or not respond at all when the turn signal lever or hazard light button are pressed.
What happens when a flasher relay goes bad?
While they are a very simple component in both design and operation, flashers play an important role in the overall driveability of a vehicle, and can compromise safety when they fail. Usually a bad or failing flasher relay will produce a few symptoms that can alert the driver of a potential issue. 1. Turn signals or hazards do not function
Why are the lights on my Turn signal not working?
While they may still light up, the lights will not be able to serve their intended purpose of signaling a turn or emergency situation. These same symptoms can also be caused by electrical issues, so having the vehicle properly diagnosed is highly recommended. 3. Additional lights are not working
Where do you plug in a turn signal Flasher?
But let’s get to it. In order to replace your bulbs, you had to access the back of the turn signal housings. Also in this location, you’ll find the plugs that connect your tail lights and front turn signals to the car’s electrical system. Unplug these and plug them back in one at a time.