What does the p0010 code mean on a car?

A P0010 code refers to the VVT (variable valve timing) or VCT (variable camshaft timing) components and the car’s PCM (powertrain control module) or ECM (engine control module). VVT is a technology used in the engine to allow it to get greater power or efficiency at different running points.

How to diagnose a p0010 Hyundai camshaft?

Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. How much do you know about cars? The cost of diagnosing the P0010 HYUNDAI code is 1.0 hour of labor.

What is the error code for the camshaft position actuator?

OBD check showed P0010, (camshaft position actuator circuit ) looked and found that a critter had eaten the wiring to the positioning solenoid. I repaired the wiring, but the error code remains. Circuit testing shows 12.43 volts on the connector a…

How much does it cost to repair a p0010 Hyundai engine?

Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P0010 HYUNDAI code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type.

What is the engine code for the p0016 engine?

Q: Engine codes detected were P0016 P0017 and P0174. The codes P0016 and P0017 are related to the crankshaft location and the camshaft location. Check the camshaft position sensor and see if its plugged in.

Where is the p0016 sensor located on a PCM?

Should the timing be off, the PCM will set a code P0016. This code stands for Crankshaft Position – Camshaft Position Correlation (Bank 1 Sensor A). Where is the P0016 sensor located?

Is there a repair cost estimate for p0016?

Due to the high number of possible causes of code P0016, as well as the wide range of current prices of replacement parts for every possible part that can fail and set this code as a result, it is not possible to provide a repair cost estimate for this code that is even reasonably accurate for any part of the USA.

When did p0013 come up on my car?

I had P0013 (Exhaust Camshaft Position Actuator Solenoid Control Circuit) come up after finishing a 5 hour drive about a year ago. Basically I cleared the code, drove back to Toronto with no problems. Code hasnt come back and I’ve put about 10,000km more on it.

How long does it take to repair a p0013 Chevy?

Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost to diagnose the P0013 CHEVROLET code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

What does Bank 1 mean in DTC p0013?

If the PCM detects an open, a short to ground, or a short to voltage, DTC P0013 sets. The “B” camshaft refers to the exhaust, right, or rear camshaft (looking at the engine from the drivers seat). Bank 1 refers to the side of the engine that contains cylinder #1.

How to fix engine code p0010 on 2.4L?

Just remove the hold-down bolts & pull up on the actuators. Put engine oil on the new o-rings & don’t over-torque the hold-down bolts (torque spec is only 7 ft-lbs). The actuators are keyed differently (& have different part numbers) so you can’t interchange them.

What does p0010 mean on a torque pro?

We recommend Torque Pro. Code P0010 is defined as “Camshaft position (CMP) actuator, intake/left/front, bank 1 circuit malfunction”, and is set when a fault is detected in the electrical circuit that controls the variable valve/cam timing system.

What is the problem code for Pontiac check engine light?

P1113Intake Resonance Switchover Valve Circuit P1114Engine Coolant Temperature (ECT) Sensor Circuit Intermittent Low Voltage – Read Our Article on Automotive Circuit TestingFor Help With This Pontiac Trouble Code

What does the check engine trouble code mean?

Basically the check engine light and associated P0010 trouble code means that the voltage in the circuit has fallen below a set limit for a specific amount of time (varies by make/model/engine). This code is specific to bank 1.

What does p0010 mean on a Pontiac G6?

P0010 is a relatively common trouble code. It only affects vehicles with variable valve timing (VVT). The list of VVT vehicles is growing, and the Pontiac G6 can have VVT, and is prone to developing this code. P0010 is a generic OBDII code.

What are the symptoms of engine code p0010?

Common symptoms of Code P0010 are: Illuminated check engine warning light. Rough running at high engine speeds. Loss of power at mid, and high range RPM’s. Increased fuel consumption.

What are the actuators on a Pontiac G6?

The Pontiac G6 utilizes camshaft actuators to change the valve lift depending on the RPM of the motor. This allows for a more efficient cam profile at any speed. This increases engine efficiency and power. Camshaft Position Actuators change the lift of the camshaft up to 25 degrees.

What are the symptoms of engine code p0016?

Code P0016 may be accompanied by several different symptoms. These including: an engine that runs poorly, an engine that cranks but will not start and an illuminated check engine light. What are common solutions to code P0016 ?

How much does it cost to repair a p0011 Volkswagen?

The cost of diagnosing the P0011 VOLKSWAGEN code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.

What should I replace camshaft position sensor on?

Replaced Camshaft position sensor, drove 90mi car ran a bit better, cleared check engine light. Started up today drove again 4 miles check engine light returned. Next try is to replace Variable Valve Timing Solenoid (Dorman 917-216).

Navigation