How to test the Honda Accord V6 engine?
(Refer to steps 1 and 2 on page 11-332 of the 2003-’06 Accord V6 Service Manual Supplement, or online, enter keyword Gauge Test, and select Fuel Gauge Sending Unit Test [V6 Engine] from the list.) 2. Start the engine, and let it idle for 2 minutes.
Why is my Honda Accord engine so hard to start?
Exhaust gas backflow into the intake manifold at engine shutdown may cause a poor mixture of intake air and fuel at the next engine start-up. Replace the fuel pressure regulator, if needed, and use the HDS to update the PGM-FI software in the ECM/PCM.
What should fuel pressure be on Honda Accord?
Start the engine, and let it idle for 2 minutes. 3. Turn off the engine. Check the fuel pressure gauge. Pressure should be 380 to 430 kpa (55 to 63 psi). 4. Monitor the fuel pressure reading. If the fuel pressure bleeds down quickly after the engine is turned off, go to the Repair Procedure.
How do you install a fuel tank on a Honda Accord?
Align the marks on the fuel tank unit and the fuel tank. (See page 11-327, step 11 of the 2003-’06 Accord V6 Service Manual Supplement.) Install the fuel tank unit into the tank without dislodging the gasket. Using hand pressure only, slide the fuel tank unit into the tank until it is properly seated.
(Refer to steps 1 and 2 on page 11-332 of the 2003-’06 Accord V6 Service Manual Supplement, or online, enter keyword Gauge Test, and select Fuel Gauge Sending Unit Test [V6 Engine] from the list.) 2. Start the engine, and let it idle for 2 minutes.
Exhaust gas backflow into the intake manifold at engine shutdown may cause a poor mixture of intake air and fuel at the next engine start-up. Replace the fuel pressure regulator, if needed, and use the HDS to update the PGM-FI software in the ECM/PCM.
Start the engine, and let it idle for 2 minutes. 3. Turn off the engine. Check the fuel pressure gauge. Pressure should be 380 to 430 kpa (55 to 63 psi). 4. Monitor the fuel pressure reading. If the fuel pressure bleeds down quickly after the engine is turned off, go to the Repair Procedure.
Align the marks on the fuel tank unit and the fuel tank. (See page 11-327, step 11 of the 2003-’06 Accord V6 Service Manual Supplement.) Install the fuel tank unit into the tank without dislodging the gasket. Using hand pressure only, slide the fuel tank unit into the tank until it is properly seated.
What causes a rough idle or a ses?
A Rough Idle or a SES can sometimes be caused by a change in the throttle body position sensor calibration. To correct any accidental changes in throttle body calibration, use these procedures to recalibrate. Note: These procedures are a little tricky to do. You must get the timing just right Use a stop watch to help the precision of your timing.
What happens if a Honda Accord loses power?
On an Accord, you will lose fuel pressure. If the main relay bad on a Civic, you will lose power to the injectors and the fuel pump, but you may not lose fuel pressure since the fuel injectors can’t open without power.
What’s the average rpm of a Honda Accord?
On several cylinders. Would cycle between 500-800 rpm, kinda hunting and gagging around, at about a 1.5 sec interval. Let it idle for about 15 mins straight, not touching anything. Eventually, it smoothed a little to 600-800 rpm. Finally, i keyed it off, waited and started it again.
What is the code for a bad crankshaft position sensor?
A diagnostic scan tool will show a code between P0335 and P0338. The check engine light doesn’t always come on, though, so you could be experiencing any of the above symptoms for some time before you see the warning light. There are a number of different problems that can cause similar symptoms to a crankshaft position sensor problem.