How to replace your Jeep Wrangler battery and upgrade?
Quadratec Extreme Duty Battery Terminals and Optima Battery Upgrade. If you’re replacing your Jeep battery with a new one, take the 10mm bolt out of the hold down clamp in the lower front and remove it entirely. Drop the new battery in place, center it, and tighten the clamp back down. If you’re reusing your battery,…
How big of a cable do you need for a Jeep Wrangler battery?
Next, move on to tighten down the two nuts that hold the brass down onto the terminals. The positive side is 9/16-inch, but you can use a 14mm. The negative side is ½-inch, or 13mm. They’re actually standard fasteners, but these metric sizes are close enough to to work. The factory cable ends go under the next ⅜-inch bolt down the rail.
Where did I go to get a new battery?
So we went to Wal-Mart and bought a battery. Got all they way back, put it in, and she cranked right up. Its about 9pm CT at this point. I get the car home, thinking all is well yada yada yada.
What’s the warranty on a Jeep Wrangler battery?
Warranty consists of 18 months free replacement. With higher cold cranking amps, AutoZone’s batteries start faster on cold days. Duralast batteries feature best-in-class vent caps, a Solidium™ Weld System, Robust Separators, LifeSpan™ negative paste and power designed to meet or exceed your Wrangler’s needs.
Which is better Duralast or AutoZone Wrangler battery?
With higher cold cranking amps, AutoZone’s batteries start faster on cold days. Duralast batteries feature best-in-class vent caps, a Solidium™ Weld System, Robust Separators, LifeSpan™ negative paste and power designed to meet or exceed your Wrangler’s needs.
So we went to Wal-Mart and bought a battery. Got all they way back, put it in, and she cranked right up. Its about 9pm CT at this point. I get the car home, thinking all is well yada yada yada.
How to do a reset on a Jeep Wrangler?
1 Disconnect the POSITIVE battery Terminal and touch it to ground for 30 seconds. (This is to discharge the PCM capacitors, which maintain the Adaptive Memory. 2 Reconnect the Battery Cable 3 Turn Ignition Switch to the “ON” position but DO NOT start the engine 4 Turn Headlight “ON” 5 Turn Headlights “OFF” 6 Turn Ignition Key “OFF”
How to erase adaptive memory on Jeep Wrangler?
Turn Ignition Key “OFF” The PCM Adaptive memory has now been flashed, or erased from the PCM. 1. Disconnect the POSITIVE battery Terminal and touch it to ground for 30 seconds. (This is to discharge the PCM capacitors, which maintain the Adaptive Memory.
Quadratec Extreme Duty Battery Terminals and Optima Battery Upgrade. If you’re replacing your Jeep battery with a new one, take the 10mm bolt out of the hold down clamp in the lower front and remove it entirely. Drop the new battery in place, center it, and tighten the clamp back down. If you’re reusing your battery,…
What kind of battery cable does a jeep TJ Wrangler use?
These are too short for the 2.4L DOHC engines used in 2003 – 2006 Jeep TJ Wranglers. 2 gauge positive battery cable with 4 ga fuse block lead. Starter lug cover to protect against accidental short circuits during oil changes. Beware of cheap kits that do not include a cover. 2 gauge negative battery cable with 6 gauge chassis ground.
1 Disconnect the POSITIVE battery Terminal and touch it to ground for 30 seconds. (This is to discharge the PCM capacitors, which maintain the Adaptive Memory. 2 Reconnect the Battery Cable 3 Turn Ignition Switch to the “ON” position but DO NOT start the engine 4 Turn Headlight “ON” 5 Turn Headlights “OFF” 6 Turn Ignition Key “OFF”
Where does the alternator wire go on a Jeep YJ?
Early Jeep YJs have a wire that goes from battery to a starter relay under the battery tray with a straight lug. The alternator wire goes from the battery side of the start relay to the alternator. See picture at left. 1989 YJ is shown.
Next, move on to tighten down the two nuts that hold the brass down onto the terminals. The positive side is 9/16-inch, but you can use a 14mm. The negative side is ½-inch, or 13mm. They’re actually standard fasteners, but these metric sizes are close enough to to work. The factory cable ends go under the next ⅜-inch bolt down the rail.
What was the problem with my 2002 Jeep Wrangler?
Start run, a little rough, but accelerating fine. After 10 of driving 2800 rpm problem returns. Code P0303 back. Drove the Jeep to the store in very cold temps. Ran rougher than before and got a new code P0135 02 Sensor error, P0300, P0304, P0303, P0305, P0306
What to do if your Jeep wont start with no power?
Got one one day ,then went to go to work the next morning and BAM it’s as if his battery was drained. Lights came on very faint and all we got was small clicks. New key ignition unit and the thing worked perfectly again. Also, your Jeep will not start if you have no power going to anything.
What kind of Jeep Wrangler wont turn over?
Enter your ride HERE to be a part of MAY’s Ride of the Month Challenge! I have a 92 wrangler 4.0 6cyl with 5 speed, 200,000 miles on it and it just died. I have no electrical, wont turn over, no lights.
What happens if you replace the battery in your car?
Also, it’s possible that everything about the battery might be fine, but some key systems could have been damaged or disabled, which could lead to some serious “side effects” for the entire vehicle. Learn which battery is right for your vehicle. Did You Replace the Battery Correctly?
When did car battery still won’t start?
This entry was originally posted on Wednesday, October 31st, 2012 at 10:00 am and is filed under Auto Repair . You can follow any responses to this entry through the RSS 2.0 feed. You can skip to the end and leave a response. Pinging is currently not allowed.
What’s the warranty on a car battery that stops working?
First of all, even the cheapest car battery should have at least a 1-year warranty which will likely cover instances where it simply stops functioning without any apparent reason. So your investment will be covered in this case.