How to repair front disc brake on Hyundai Sonata?
1. Place a dial gauge about 5mm (0.2 in.) from the outer circumference of the brake disc, and measure the runout of the disc. 2. If the runout of the brake disc exceeds the limit specification, replace the disc, and then measure the runout again.
How can I repair my Hyundai Elantra brake system?
Make sure the brake fluid in the reservoir is at the MAX (upper) level line. 2. Have someone slowly pump the brake pedal several times, and then apply pressure. 3. Loosen the right-rear brake bleed screw (A) to allow air to escape from the system. Then tighten the bleed screw securely. 4.
What to do if your brake system is not working?
Check brake operation by applying the brakes during a test drive. If the brakes do not work properly, check the brake booster. Replace the brake booster as an assembly if it does not work properly or if there are signs of leakage. Check brake operation by applying the brakes. Look for damage or signs of fluid leakage.
When to replace brake light switch on Hyundai Sonata?
This should cover years from 2006 to 2010. It is very simple procedure and it should not take you more than 5 minutes to do it yourself. If your ABS & ESC OFF light are all the time On then most likely it is a faulty brake light switch. Sometimes you might have the ESC OFF light only.
Why are my brake pads sticking on my Hyundai Sonata?
As you replace the shims and clean everything up, go ahead and replace the pads too. Your Sonata’s disk brakes use pistons to push the brake pad into the rotor. These pistons have a rubber seal around them. This seal can go bad and the piston will start to lose its free movement.
How do you change the brake pads on a Hyundai?
Set the parking brakes and place the transmission in Park. Open Brake Fluid Reservoir. Start by opening the hood and remove the brake fluid reservoir cap. This is necessary and will make it possible for you to press the caliper pistons in. You will need to do this to fit the new thicker brake pads in the brake caliper.
How to repair front disc brake on Hyundai Santa Fe?
1. Place a dial gauge about 5mm (0.2 in.) from the outer circumference of the brake disc, and measure the runout of the disc. 2. If the runout of the brake disc exceeds the limit specification, replace the disc, and then measure the runout again. 3.
How to change the rear brake pads on a Landrover?
This shows how to change the rear brake pads on cars fitted with the EPB, electronic parking brake. It’s on a Landrover Discovery Sport but is the same method on lots of cars with EPB like VW, Audi etc. No parts specified. Insert wisdom here. Almost done! Just follow the video for how to change the rear pads on cars fitted with EPB.
How to change brake pads with an electric parking brake?
1. Connect a car battery charger 2. Connect a diagnostic tool 3. Replace brake pads and push back pistons 4. Press the foot brake pedal 5. Connect the diagnostic tool again 6. Set a basic Setting 7. Test the electric parking brake function You are done! How do I know if I need a computer to replace my rear brake pads?
Can you change brake pads on a Japanese car?
Fits most European and Japanese cars… Once your pistons are pushed in, you can now replace the brake pads. Ensure you lubricate any moving parts and clean everything not to get stuck, so you have to redo the job soon. Replace any metal plates if you got them in the brake pads package.
1. Place a dial gauge about 5mm (0.2 in.) from the outer circumference of the brake disc, and measure the runout of the disc. 2. If the runout of the brake disc exceeds the limit specification, replace the disc, and then measure the runout again.
1. Connect a car battery charger 2. Connect a diagnostic tool 3. Replace brake pads and push back pistons 4. Press the foot brake pedal 5. Connect the diagnostic tool again 6. Set a basic Setting 7. Test the electric parking brake function You are done! How do I know if I need a computer to replace my rear brake pads?
Do you need to change rear brakes on 2017 Legacy?
Don’t know which changes the rear brakes. but after watching several u-tubes on changing rear pads on earlier models I started with my 2017 legacy and came to the outback.org since i can’t find one for legacy and was told most things on legacy and outback are the same.
Fits most European and Japanese cars… Once your pistons are pushed in, you can now replace the brake pads. Ensure you lubricate any moving parts and clean everything not to get stuck, so you have to redo the job soon. Replace any metal plates if you got them in the brake pads package.
How to adjust the parking brake on a Hyundai Accent?
Apply a coating of the specified grease to each sliding parts (A) of the ratchet plate or the ratchet pawl. 4. Install the parking brake cable adjuster, then adjust the parking brake lever stroke by turning adjusting nut (A). After repairing the parking brake shoe, adjust the brake shoe clearance, and then adjust the parking brake lever stroke.
What’s the average speed of a Hyundai Sonata?
Hand type – While operating the arking brake pedal for 68.6N (7kgf, 15.4 lbf) effort, drive the vehicle 500 meters (0.31 miles) at the speed of 60kph (37 mph). Foot type – While operating the parking brake lever for 98N (10kgf, 22lbf) effort, drive the vehicle 500 meters (0.31 miles) at the speed of 60kph (37 mph).
How do you remove a brake caliper from a car?
Lift the caliper off the brake pads and tie it with a rope to the strut to keep it from falling and void, putting tension on the brake line. Remove Brake Pads Once you remove the two bolts, you will pull out the caliper and remove the brake pads. Loosen the two rotor retaining bolts using a Phillips screwdriver.
Set the parking brakes and place the transmission in Park. Open Brake Fluid Reservoir. Start by opening the hood and remove the brake fluid reservoir cap. This is necessary and will make it possible for you to press the caliper pistons in. You will need to do this to fit the new thicker brake pads in the brake caliper.
How do you remove a rotor from a Hyundai?
Remove rotor Removing the old rotor can be tricky. Remove the screw that holds the rotor secure. Next, you need to remove the rotor. Try wiggling the rotor back and forth. If the rotor does not come loose, you may have to use a hammer to get it off. Spray penetrating oil and let it sit for 10 minutes before you try to remove the rotor.