How to repair a Kia Sedona engine control module?
1. Install in the reverse order of removal. 1. TEST ECM GROUND CIRCUIT: Measure resistance between ECM and chassis ground using the backside of ECM harness connector as ECM side check point. If the problem is found, repair it.
Is there a problem with the Kia Sedona ECM?
If problem is not found in Step 1 and 2, the ECM could be faulty. If so, replace the ECM with a new one, and then check the vehicle again. If the vehicle operates normally then the problem was likely with the ECM.
How do you fix the front wiper motor on a Kia Sedona?
1. Connect the connector after installing the wiper motor & linkage assembly. 2. Install the cowl top cover. 3. Install the windshield wiper arm and blade. 4. Install the wiper arm and blade to the auto stop position. Common sources of contamination are insects, tree sap, and hot wax treatments used by some commercial car washes.
How to change the VIN on a Kia Sedona?
1. Select “VIN Writing” function in “Vehicle S/W Management”. 2. Select “Write VIN” in “ID Resister”. 3. Enter the VIN. Before entering the VIN, double-check the VIN as it cannot be changed once programmed. 4. Turn the ignition switch OFF, then back ON.
What are the components of a Kia Sedona?
1. Engine Control Module (ECM) 2. Barometric Pressure Sensor (BPS) 3. Manifold Absolute Pressure Sensor (MAPS) 4. Intake Air Temperature Sensor (IATS) 5. Engine Coolant Temperature Sensor (ECTS) 6. Throttle Position Sensor (TPS) [integrated into ETC Module] 7. Crankshaft Position Sensor (CKPS) 8. Camshaft Position Sensor (CMPS) [Bank 1 / Intake]
1. Install in the reverse order of removal. 1. TEST ECM GROUND CIRCUIT: Measure resistance between ECM and chassis ground using the backside of ECM harness connector as ECM side check point. If the problem is found, repair it.
If problem is not found in Step 1 and 2, the ECM could be faulty. If so, replace the ECM with a new one, and then check the vehicle again. If the vehicle operates normally then the problem was likely with the ECM.
What happens when you open the sunroof on a Kia Sedona?
When the heater or air conditioning system is on with the sunroof opened, the outside (fresh) air position will be automatically selected. At this time, if you press the recirculated air position …
1. Select “VIN Writing” function in “Vehicle S/W Management”. 2. Select “Write VIN” in “ID Resister”. 3. Enter the VIN. Before entering the VIN, double-check the VIN as it cannot be changed once programmed. 4. Turn the ignition switch OFF, then back ON.
Are there any problems with the Kia Sedona?
Next day, ck engine light off. Dealer ck’d and found no problems. Drove fine until last night. Same problem (and happened at practically same location – will explain later). Drove home, ate dinner. Needed to run errand, so drove it around block (after about an hour of rest) and car drove fine.
Why is my Kia Sedona stuck in 3rd gear?
She was on a trip about 100 miles from home and a big “clunk” which sounded like it came from under the car occured. Then the car acted like it was stuck in 3rd gear. She limped in to a transmission shop and turned off the engine. When the mechanic got in to test drive it didn’t do the same thing.
When the heater or air conditioning system is on with the sunroof opened, the outside (fresh) air position will be automatically selected. At this time, if you press the recirculated air position
Where are the fuses on a Kia Sedona?
Rear cargo area panel Fuse name Fuse rating [A] Circuit protected RR D/LOCK 20 Sliding door lock relay, Sliding door un RR WIPER 15 Rear wiper relay, Rear wiper motor RR DEFOG 25 Rear window defroster relay, Rear window POWER TAIL GATE 30 Power tailgate module
Where is the diagnostic connector on a Kia engine?
Scan Tool for Codes and Live Data for your Kia Engine from $149.95 Kia Engines – Please select the connector for your vehicle from the options below. This connector is usually located under the driver side dash panel. Locations: Left-hand side of firewall. Near or in the fuse box, or near the battery.
1. Engine Control Module (ECM) 2. Barometric Pressure Sensor (BPS) 3. Manifold Absolute Pressure Sensor (MAPS) 4. Intake Air Temperature Sensor (IATS) 5. Engine Coolant Temperature Sensor (ECTS) 6. Throttle Position Sensor (TPS) [integrated into ETC Module] 7. Crankshaft Position Sensor (CKPS) 8. Camshaft Position Sensor (CMPS) [Bank 1 / Intake]
What are the wiring diagrams for a Kia Sedona?
Kia Sedona 2002-2006 Wiring Diagrams – Illumination Lamps (I-2a, I-2b).gif Kia Sedona 2002-2006 Wiring Diagrams – power train control system (PCM).gif Kia Sedona 2002-2006 Wiring Diagrams – Sunroof system & Overhead console.gif
Scan Tool for Codes and Live Data for your Kia Engine from $149.95 Kia Engines – Please select the connector for your vehicle from the options below. This connector is usually located under the driver side dash panel. Locations: Left-hand side of firewall. Near or in the fuse box, or near the battery.
How to turn off the ECM on Kia Sportage?
After finishing “ECM Neutral Mode”, turn IGN ON then OFF using the smart key or start button. Then the ECM learns information on the smart key automatically. Turn IGN ON then OFF using the smart key or start button. Then the ECM learns information on the smart key automatically.
After finishing “ECM Neutral Mode”, turn IGN ON then OFF using the smart key or start button. Then the ECM learns information on the smart key automatically. Turn IGN ON then OFF using the smart key or start button. Then the ECM learns information on the smart key automatically.