How to remove washer motor from Kia Sportage?
1. Disconnect the negative (-) battery terminal. 2. Remove the engine room under cover. 3. Remove the front wheel guard [RH]. 4. Drain the washer fluid to less than 650 cc. 5. Disconnect the washer hose (A) and washer motor connector (B). 6. Remove the front washer motor (C). 1. Disconnect the negative (-) battery terminal. 2.
Why is my windshield wiper not working on my Kia Sportage?
The dealer rotated the tires, but the shaking persisted. Thirdly, a tire blew out and had to be changed. In addition, the vehicle began leaking transmission fluid and a new transmission line was installed. Lastly, the windshield wiper motor stopped working and the entire driver’s side glass caved in on the contact, but did not break.
Why is my Kia windscreen washer not working?
Hi as same problem front and back wipers work fin rear screen wash works fine just front decided to stop.
What to do if your front washer is not working?
Multi-function switch (wiper/washer switch). Circuit (s). Front washer pump relay. Washer pump. GO to Pinpoint Test E . Generic electronic module (GEM). Multi-function switch (wiper/washer switch). Circuit (s). Front washer pump relay. Rear washer pump relay. Washer pump. GO to Pinpoint Test J .
1. Disconnect the negative (-) battery terminal. 2. Remove the engine room under cover. 3. Remove the front wheel guard [RH]. 4. Drain the washer fluid to less than 650 cc. 5. Disconnect the washer hose (A) and washer motor connector (B). 6. Remove the front washer motor (C). 1. Disconnect the negative (-) battery terminal. 2.
Hi as same problem front and back wipers work fin rear screen wash works fine just front decided to stop.
What to do if your rear washer is not working?
Before you start, you can easily check that your pump is not blocked. If you open the boot lid, between the hinges you can see the washer pipe with a joint in it. Just disconnect one end of the joint and verify water is dispensed when you activate the rear wash.
What should I do if my windshield washer pump is not working?
Fill the pump’s reservoir to the necessary level with the solution. Use a funnel to help you. Use a formulated, non-freezing washer fluid in the wintertime. Unclog dirt from nozzles, hoses or screens. Use a long pin or fine wire to pick out or poke through clogged dirt. Follow by rinsing the parts that are exposed with water.
How do you clean a Kia washer motor?
1. With the washer motor connected to the reservoir tank, fill the reservoir tank with water. Before filling the reservoir tank with water, check the filter for any foreign material or contamination. If necessary, clean the filter. 2.
What should I do if my windshield washer is not working?
Use a long pin or fine wire to pick out or poke through clogged dirt. Follow by rinsing the parts that are exposed with water. Have someone else turn on your car’s ignition. Ask them to activate the washer system to send out fluid. Let the washer fluid solution flush the system of remaining dirt or deposits.
Why is my windshield washer not sending out fluid?
If your washer fluid is not being sent out when activated, the solution could simply be filling the washer system’s reservoir with more fluid or cleaning the nozzles and hoses. In more severe cases, the washer pump may need to be replaced. Here are steps to troubleshoot a windshield-washer pump. Check the washer fluid reservoir for dirt.
What should I do if my windshield wiper hose is leaking?
Perform a visual inspection for rips or tears in the hose. Have an assistant activate the washer fluid while you check for leaks in the hose. If possible, repair the hose, preferably with non-adhesive rubber automotive tape. This is a special tape which is made of rubber.
How do you remove a hose from a windshield washer?
Disconnect the hose from the bottom of the jet. The rubber hose on the bottom of the jet is held on solely by the pressure the hose exerts on the nozzle, so you should be able to pull it off with relative ease. Simply squeeze the hose with your index finger and thumb near the nozzle and pull backwards to remove it.
Where does the windshield wiper hose come from?
Open the hood of your vehicle and inspect the windshield wiper hose. The hose runs from the washer fluid reservoir to the spray nozzles on the hood. It’s usually a clear plastic or black plastic hose. Perform a visual inspection for rips or tears in the hose.
How do you replace a washer fluid hose?
Pull the hose clamp off the hose at the washer fluid reservoir and pull the hose off of the reservoir tank. Then, pull the hose off the nozzles. Replace the hose. Installation is the reverse of removal. “Auto Repair For Dummies; Deanna Sclar”, IDG Books Worldwide; 1999
1. With the washer motor connected to the reservoir tank, fill the reservoir tank with water. Before filling the reservoir tank with water, check the filter for any foreign material or contamination. If necessary, clean the filter. 2.
Where is the E-CVVT located on a Kia Sportage?
Description Electric E-CVVT system is electric continuous variable valve timing system. It is located on the intake camshaft of the engine and uses motor rotation to control the rotation angle of camshaft relative to the rotation of crankshaft regardless of engine pressure.