How to remove the cylinder switch from a Mazda Protege?

ECT sensor signal characteristic (reference) Circuit Open/Short Inspection fPage 210 Door Lock Cylinder Switch: Service and Repair DOOR KEY CYLINDER SWITCH REMOVAL/INSTALLATION 1. Close the door glass completely. 2. Disconnect the negative battery cable. 3. Remove the passenger-side front door trim.

What do you need to know about a Mazda Protege?

Preparing document for printing… Specifications Engine Control Module: Specifications PCM INSPECTION CAUTION: The PCM terminal voltages vary with change in measuring conditions and vehicle conditions. Always carry out a total inspection of the Input systems, output systems, and PCM to determine the cause of trouble.

How to change the ECT sensor on a Mazda Protege?

Place the ECT sensor in water with a thermometer, and heat the water gradually. Specification 4. Measure the resistance between the ECT sensor terminals A and B using an ohmmeter. – If not as specified, replace the ECT sensor.

How to replace the sunroof relay on a Mazda Protege?

– If not as specified, replace the relay. fPage 37 fSunroof / Moonroof Relay: Service and Repair fSUNROOF RELAY REMOVAL/INSTALLATION NOTE: Sunroof relay is built in the sunroof motor. fTesting and Inspection Daytime Running Lamp Control Unit: Testing and Inspection DRL CONTROL MODULE INSPECTION (CANADA) 1.

How do you check the PCM on a Mazda Protege?

PCM Inspection Using the SST (104 Pin Breakout Box) 1. Disconnect the negative battery cable. 2. Disconnect the PCM connector. 3. Connect the SST (104 Pin Breakout Box) to the PCM as shown. 4. Tighten the connector bolt. Tightening torque 7.9 – 10.7 N.m {80 – 110 kgf.m, 69.5 – 95.4 in.lbf} 5. Connect the negative battery cable.

How do you change the lock on a Mazda?

Use the following procedure to change the setting. Switch the ignition off and close all of the doors and the liftgate. Open the driver’s door. Within 30 seconds of opening the driver’s door, press and hold the LOCK button on the key for 5 seconds or longer.

When do Mazda doors and liftgates lock automatically?

A beep sound is heard when all doors and the liftgate are closed while the advanced key is being carried. All doors and the liftgate are locked automatically after about three seconds when the advanced key is out of the operational range. Also, the hazard warning lights flash once.

How do you open the doors on a Mazda?

Switch the ignition off and close all of the doors and the liftgate. Open the driver’s door. Within 30 seconds of opening the driver’s door, press and hold the LOCK button on the key for 5 seconds or longer. All of the doors and the liftgate lock and the beep sound activates at the currently set volume.

What kind of fasteners do I need for a Mazda?

We have the Mazda clips and fasteners you need for repairs inside, outside and under the hood. That includes Mazda fender liner clips and OEM-style Mazda auto body clips. Pick up some of our Mazda trim panel clips, and you won’t have to worry about missing and damaged pieces when you remove interior parts.

How to tell if your Mazda car is at fault?

Trace in GREEN the portion of the circuit below that you suspect could be at fault. Both LOW BEAM HEADLAMPS do not work. The lamps work correctly on the High Beam and Flash (passing) positions. The tail lamps function correctly. 2. Trace in RED the portion of the circuit below that you suspect could be at fault.

What kind of inspection should I do on my Mazda Protege?

Always carry out a total inspection of the Input systems, output systems, and PCM to determine the cause of trouble. Otherwise, a wrong diagnosis will be made. PCM Inspection Using the SST (104 Pin Breakout Box) 1.

https://www.youtube.com/watch?v=dC1R1lb0m5k

What is the coolant temperature sensor on a Mazda Protege?

Vacuum hose fPage 241 fEngine – Coolant Temperature Sensor/Switch: Testing and Inspection fENGINE COOLANT TEMPERATURE (ECT) SENSOR INSPECTION NOTE: Perform the following test only when directed. ECT Sensor Resistance Inspection 1. Drain the engine coolant. 2. Remove the ECT sensor. 3.

What is the wiring diagram for a Mazda Protege?

Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 1999-2002 Mazda Protege . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle.

What kind of resistor does a Mazda Protege need?

NOTE #1: THIS IS A 1-WIRE DOOR LOCKING SYSTEM, TO LOCK REQUIRES A (-)NEGATIVE THRU A 1500 OHM RESISTOR. TO UNLOCK REQUIRES A STRIGHT (-) NEGATIVE TO THE SAME WIRE.

When to replace the relay on a Mazda Protege?

– If not as specified, replace the relay. fPage 361 fCamshaft Position Sensor: Service and Repair fCAUTION: When foreign material such as an iron chip is on the CMP sensor, it can cause abnormal output from the sensor because of flux turbulence and adversely affect the engine control.

Navigation