How much does it cost to diagnose a p0028 Subaru code?
The cost to diagnose the P0028 SUBARU code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour. How much do you know about cars? When is the code detected?
What does p0028 mean on an intake valve?
P0028 is a diagnostic trouble code (DTC) for “Intake Valve Control Solenoid Circuit Range/Performance (Bank 2)”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.
What causes the p0028 OBD-II trouble code?
What causes the P0028 code? The ECM activates the intake valve solenoid for bank 2, but the valve lift mechanism did not change. The intake valve lift solenoid for bank 2 is shorted or has an open circuit.
How long does the p0028 code stay in memory?
In this regard, if in the next three drive cycles no faults had been detected (e.g. if the P0028 was a single “event”), the CEL would have gone out on its own and the cruise control restored, while the trouble code itself would have remained in memory for up to 40 drive cycles. This might have been useful for the dealer.
What are the possible causes of a p0028 Subaru?
P0028 SUBARU Possible Causes. Dirty engine oil. Low engine oil level. Faulty intake valve control solenoid. Intake valve control solenoid harness is open or shorted. Intake valve control solenoid circuit poor electrical connection.
What does the OBD II fault code p0028 mean?
What Does Code P0028 Mean? OBD II fault code P0028 is defined as “ Intake Valve Control Solenoid Circuit Range/Performance (Bank 2)”, with “Bank 2” denoting the side of the engine opposite the cylinder #1 on engines with two cylinder heads.
How to diagnose intake valve control solenoid circuit p0028?
NOTE: When diagnosing code P0028, start the procedure by inspecting the engine for oil leaks that could have reduced the engine oil level. Repair oil leaks as required, top off the oil level, clear the code, and operate the vehicle. Rescan to see if the code returns. If the code persists, proceed as follows-
In this regard, if in the next three drive cycles no faults had been detected (e.g. if the P0028 was a single “event”), the CEL would have gone out on its own and the cruise control restored, while the trouble code itself would have remained in memory for up to 40 drive cycles. This might have been useful for the dealer.
The cost to diagnose the P0028 SUBARU code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour. How much do you know about cars? When is the code detected?
What are the codes for Subaru check engine light codes?
P1086Tumble Generator Valve #2 (LH) Position Sensor Circuit Low Input P1087Tumble Generator Valve #2 (LH) Position Sensor Circuit High Input P1088Tumble Generator Valve #1 (RH) Position Sensor Circuit Low Input P1089Tumble Generator Valve #1 (RH) Position Sensor Circuit High Input P1090Tumble Generator Valve #1 (RH) Malfunction (Stuck Open)
Why does my Subaru check engine light keep showing up?
Subaru check engine light shows up if there is an issue with the Subaru computer emissions control system. Then the Subaru’s computer which is usually called ECU will produce error codes that relate specifically to the particular sensor affected in the car. If anyone of these sensors fails, it will prompt a fault or an error code.
How much does it cost to repair a Subaru OBDII code?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P0028 SUBARU code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.
What causes a p0028 code on a valve lift?
Oil level and leaks around the variable valve lift solenoids or pressure sensor switches have been seen before as causes of the P0028 code, as has been noted above. The code is for bank 2. The related solenoid and switch are at the front of the left side head and easily checked for oil leaks.