Why does my Eaton Fuller not shift gears?
My eaton fuller autoshift suddenly will not go into any gears in my driveway, just shows down arrows and R or 2 (flashing) when I try to go into any gear. When i have the truck off and turn key to start position and try to shift gears i can hear the transmission shifting successfully, however once the engine is running it will not shift gears.
How much does it cost to diagnose a p1707 code?
The cost of diagnosing the P1707 code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
Why does Autoshift not go into any gears?
When i have the truck off and turn key to start position and try to shift gears i can hear the transmission shifting successfully, however once the engine is running it will not shift gears. There are no service lights or error codes being displayed.
Why does the transmission not go into gear when the car is running?
The transmission won’t shift and the car makes a grinding sound when the engine is running. Besides, pulling out of first gear will feel harder than normal. The transmission will shift in and out of gear without any issue when the car is not running.
What happens if there is no lubricant in the gearbox?
If there is no lubricant in the gearbox, you could have done major damage to the engine and gearbox components by running the car. You could end up with an expensive repair and even replacement of the whole transmission system.
How to get a fault code on a Freightliner?
Turn the ignition key ON but do not start the engine. If the engine is already running, you may still retrieve codes, however, do not engage the starter if engine stalls. 4. To Retrieve Active Codes: Start with the key in the ON position. Turn the key OFF and ON two times within five seconds ending with the key in the ON position.
How to retrieve Eaton Fuller transmission fault codes?
Place the shift lever in neutral. Set the parking brake. Turn key on with engine off. Note: If the engine is already running, you may still retrieve codes; however, do not engage the starter if the engine stalls. To Retrieve Active Codes: Key on. Turn key off and on 2 times within five seconds ending with the key on.
What causes a slipout on an Eaton Fuller transmission?
Under the right conditions, slipout will result. Some of these conditions are: Transmission mounted eccentrically with engine flywheel pilot. Excessive gear clashing which shortens clutching teeth. Incorrect adjustment of remote shift control linkage resulting in partial engagement. Also check for loose connections and worn bushings.
https://www.youtube.com/watch?v=dvCgeSc37L8
Is there charge for Eaton Fuller Autoshift service?
There is no charge for this service, but standard message and data rates may apply. My eaton fuller autoshift suddenly will not go into any gears in my driveway, just shows down arrows and R or 2 (flashing) when I try to go into any gear.
How to troubleshoot an Eaton heavy duty transmission?
Guide to servicing and repairing Eaton Fuller heavy-duty truck transmission, assistance locating the issue of transmission trouble, analyze the cause and make necessary repairs for 7, 8, 9, 10, 13, 15 and 18 speed Eaton transmissions. For more in-depth assistance refer to your transmission model service manual or give us a call at 877-776-4600.
Why is my Eaton ultrashift truck not starting?
Today the driver shut the truck off and when tried to restart the truck, it wouldn’t start. We quickly figured out the reason the truck wasn’t starting was it was in gear and the neutral light wasn’t on in the console.
What to do if Autoshift won’t go into gears?
Click to expand… just disconnect the negative battery cable for about 5 full minutes. reconnect, and see what happens. then make sure to check the tightness of all the battery cables as well. Checking the grounds… Start at the battery box and work out on each cable, + and -.
How can I tell if my truck is not starting?
A test for DC voltage between a ground point (eg. battery negative terminal or the engine block) and the large wire on the starter can diagnose a blown fuse (it will read 0V) but it can’t be used to indicate if the connection or starter are ok.
What kind of lubrication does Eaton Fuller transmission use?
Eaton Fuller transmissions are designed so that the internal parts operate in a bath of oil circulated by the motion of gears and shafts. Thus, all parts will be amply lubricated if these procedures are closely followed: 1.
https://www.youtube.com/watch?v=8kBwYIlS-08
When did the Eaton ultrashift 10 speed come out?
Discussion in ‘ Trucks [ Eighteen Wheelers ] ‘ started by giannid, May 16, 2018 . We’ve got a 2010 International 8600 with an Eaton Ultrashift 10 speed.
How to retrieve Eaton transmission fault code DTC-truck?
1. Place the shift lever in neutral. 2. Set the parking brake. 3. Turn the ignition key ON but do not start the engine. If the engine is already running, you may still retrieve codes, however, do not engage the starter if engine stalls. 4. To Retrieve Active Codes: Start with the key in the ON position.
What kind of engine does a Peterbilt 387 have?
****OVERHAULED******2012 Peterbilt 387 with Raised-roof Sleeper, GVWR 52,350, FR 12,350, RR 20,000 ea., Paccar MX13, 455 HP Deleted, AUTOMATIC Eaton 13 speed transmission, Trans and upper engine ov… See More Details Enter search information and click the Search button below. Use the TAB key to move between fields.
How often do you change the oil in an Eaton Fuller transmission?
Eaton Fuller transmissions are designed so that the internal parts operate in a bath of oil circulated by the motion of gears and shafts. 1. Maintain oil level. Inspect regularly. 2. Change oil regularly. 3. Use the correct grade and type of oil. 4. Buy from a reputable dealer. Change the oil filter when fluid or lubricant is changed.
What to do if your transmission is hard shifting?
To determine if the transmission itself is the cause of hard shifting, remove the shift lever or linkage from the top of the transmission. Then, move the shift blocks into each gear position using a pry bar or screwdriver. If the yoke bars slide easily, the trouble is with the linkage assembly.
Is there an Eaton that will not go into gear?
Discussion in ‘ Trucks [ Eighteen Wheelers ] ‘ started by RidinDirty11, Aug 20, 2015 . Hello everyone. Here is brain teaser for you people who have worked on these transmissions. I have a Eaton 3 pedal Auto shift transmission. It will not go into gear. Here is the problem, what happened, and what it is now doing.
Why does my SMARTSHIFT not go into gear?
Elaborate a bit please. Won’t go into gear… while you’re stopped? Like I said in another thread, if an autoshift has the clutch not adjusted correctly, the clutch brake won’t be reached, and the transmission won’t go into gear until the input shaft is stopped.
Why are the yoke bars on my Eaton Fuller not working?
Yoke bars binding in the bar housing as a result of cracked housing, over-torqued shift block lockscrew, sprung yoke bar, or swelled areas of the yoke bar. If hard shifting occurs only in first and reverse, the shift block detent plunger movement may be restricted.
How does a synchronized range shift work on an Eaton transmission?
Shift range from LOW to HIGH and HIGH to LOW by moving the shift lever fully to the right or fully to the left as described in the Operation section. The transmission will automatically make th e synchronized range shift as the shift lever is moved fully left or right.
What causes vibration in an Eaton Fuller transmission?
Although the effects of vibration will show up in the transmission, vibration usually originates somewhere else in the drive train. Vibration can usually be felt or heard by the driver; however, in some cases, transmission damage caused by vibration will occur without the driver’s knowledge.
How to check for an Eaton transmission error?
For all questions concerning inspection, removal, replacement, or adjustment procedures, refer to Eaton or OEM Service and Parts Literature. 1a. After activating the retrieval of codes, to read transmission errors via the Service Transmission light, observe the sequence of flashes exhibited by th e light.
What to look for in an Eaton Fuller automatic transmission?
Check the wiring between the Transmis- sion ECU and the Push Button Shift Control. Gear Display Lamp check: This is OK. Dash on the Gear Display: Transmission ECU and the Push Button Shift control are communicat- ing. The transmission is trying to verify Neutral and it can’t. It may be torque locked in gear. Or bad Powers and Grounds.
Is the Autoshift transmission based on a manual transmission?
The AutoShift transmission, based on the RT Series manual transmission, is an advanced shift-by-wire system that communicates with the engine utilizing the SAE-J1939 protocol for precise control of the engine and transmission functions.
What’s the replacement for an Eaton Fuller shift knob?
Replacement for EATON FULLER Style 9 – 10 Speed Shift Knob Transmission Selector A6909 or A5010 NEW EATON FULLER Style 9 – 10 Speed Shift Knob Transmission Selector A6909 or A5010 All you need in a special price. There’s a problem loading this menu right now.
Where can I find Fuller transmission parts Manual?
Below you will find a comprihesive list of Fuller transmission parts manuals, parts breakdowns, and PDF parts lists that will help you identify what parts you need to repair or rebuilt your Fuller transmission. Call us today at 877-776-4600 if you don’t see your model or you have questions. You can also order from us right on the phone!
How does a fuller Auto Shift transmission work?
Fuller’s auto-shift transmissions are a boon to drivers but sometimes a headache for mechanics. Auto-shift transmissions use what is essentially an ordinary manual transmission with an electric-motor-driven shifter assembly and an on-board electronic control unit (ECU).
Where is the Air Line on an Eaton Fuller transmission?
Remove range cylinder cover andrepair leaking range piston or piston seal. After repair, check for proper range operation. Remove the 1/4″ I.D. rubber air line at the high range supply port on the range cylinder. Feel for air flow from the open port on the range cylinder.
How can I check my Eaton transmission air line?
Move the range selector lever down to low range. Check for constant air flow from the exhaust “E” port. Constant air flow from the “E” port. No air flow from “E” port. Move the range selector up to high range. Disconnect the small air line connected to the “P” port of the shift knob. Check for air flow from the port and air line.
How much is the Eaton XY shifter worth?
The xy shifter alone is worth about 1200 bucks. Not to mention the TCU and sensors and wiring harness. My old Western Star with the 18 speed goes into neutral with the move of a gearshifter. Never dings at me when I try shift a gear either lol
What kind of engine does a Freightliner Columbia have?
I have a 2006 freightliner Columbia with mbe4000 engine and 12 speed smart shift. 48,000 miles. Going down highway check engine light came on,cruise kicked out, trans stuck in 12th gear. Pulled off ro…
What does the F mean on an automatic transmission truck?
When I turn the truck on and its in neutral is has an “N” which alternates back and fourth with an “F”. When I try to put it into drive the N changes to a 2 with the down arrow on the left of it also alternating with the “F”.
What is the XY shifter in a truck?
Click to expand… The XY shifter, is an electro/mechanical component containing 2 electrical shift motors which are responsible for moving the shift gate on top of the transmission, It gets instructions from the TCU… The TCU MUST HAVE a good clean power supply…
Why does my school bus not shift into neutral?
FOund out also that when she went to shift into “N” when this all happens it will not shift into neutral. Has to be shut off to make it go to neutral. This happens when she is moving already so shouldn’t have anything to do with the brake as far as starting out and shifting with your foot on the brake.
Why does my Blue Bird not shift into neutral?
Blue Bird mentioned brake switch problem. This happens driving down the road or when trying to shift into gear from neutral? Assuming it has one, is the goofy little light coming on on the dash that says when you are pushing the brake pedal? Could be a brake light relay if it isn’t…we’ve changed more than a couple.
Why does my Eaton transmission make a lot of noise?
There will always be a certain level of noise due to the normal transmission operation. However, excessive noise or unusual noise such as a whine, growl, or squeal indicates some kind of a problem. The transmission itself can be the cause of excessive or unusual noise.
Why does my automatic transmission not go into gear?
When its working that arrow is blinking and as my foot is on the brake pedal with all brakes released I can hear and feel the engine or transmission or whatever “activate” or whatever and then it shifts into gear. But now that little arrow to the left isn’t blinking and just nothing at all is happening.
How to troubleshoot an Eaton ultrashift plus fault code?
When troubleshooting an Inactive fault code, use the Fault Isolation Procedures to guide you to the wiring and connectors associated wi th that fault. Once PD Mode is activated, flex the wiring harness and connectors to attempt to recreate the fault.