Where is the water pump on a 1991 Honda Accord?

In the 1991 Honda Accord, the water pump is located on the left side of the engine just behind the front left tire.

How often should the timing belt be replaced on a Honda Accord?

As per Honda, your timing belt needs to be serviced every 50,000 to 80,000 miles. While you’re in there, there are a few other important things to address like the timing balancer and the water pump. This article will guide you through the process of replacing the timing belt, timing balancer, and the water pump on your Accord.

Can A P / s bolt be removed from a Honda Accord?

Figure 3. P/S bolt and tensioner. The power steering pump can be removed from its bracket to gain more room. The hoses do not need to come off. The alternator as well as its related belt will need to come off in order to gain more clearance to the timing belt and water pump.

How to remove timing belt and timing balancer?

Timing tensioner. Before moving on to the next step, it’s wise to drain the coolant. Place a pan under the car, and turn the petcock on the bottom of the radiator to release. Now that the coolant has been drained and the timing belt as well as the balancer have been removed, the water pump can come out. Remove the bolts in red (Figure 12).

How long does a Honda timing chain last?

The timing chain should last you the life of your engine although there are occasions when it could fail and wear out on you. Typically, however you can expect the time you change the last over 200,000 miles. Timing belts are usually composite rubber belts with teeth on the inside to grip the gears of the camshaft and the crankshaft.

When to replace timing belt?

Every car manufacturer recommends replacing the timing belt after a given time, and it is imperative to take this advice. The time or distance between timing belt replacement depends on the specific make and model of the vehicle, but on average it should be changed every 100,000 miles.

When to replace timing belt/chain?

A timing belt typically needs to be replaced between 40,000 and 100,000 miles depending on the vehicle and it’s a few hundred dollar repair. A timing chain doesn’t need to be replaced unless there is a problem with it.

How much does it cost to replace a timing belt on?

“Now, more people know about it and what can happen when it breaks.” Replacing a timing belt for preventive reasons typically costs $500 to $900 . However, replacing a broken timing belt may cost up to $2,000 or more if it caused damage to the valves, pistons or water pump.

Which Hondas have timing chains?

All the V6 Honda engines in regular production have timing belts (J30, J32 , J35). They switched to chains when the “K” series engine came out (4cyl) and the S2000 has always had a chain (F22).

If this happens, the old water pump will need to be removed and replaced with a new one. In the 1991 Honda Accord, the water pump is located on the left side of the engine just behind the front left tire.

What does the water pump do on a Honda Element?

This procedure applies to the Honda Accord, Element, CR-V and Acura TSX. The water pump is responsible for circulating coolant in the engine block. On Honda K24 series engines, the water pump is driven by the accessory belt, instead of the timing belt.

What does the water pump do on a Honda K24?

The water pump is responsible for circulating coolant in the engine block. On Honda K24 series engines, the water pump is driven by the accessory belt, instead of the timing belt. This makes replacing the water pump fairly easy.

How to remove a water pump from a car?

Take off the timing belt and make sure that the engine doesn’t turn at any time during the removal or replacement process. Unscrew the six bolts holding in the water pump, making sure to keep track of which hole each bolt came from. The bolt heads are 1 mm in diameter. Pull the water pump and O-ring from the motor to complete the removal process.

How do you replace a water pump on an Audi A3?

A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench. For applications where the water pump is driven by the timing belt, the timing belt must be removed.

How do you replace a water pump on a Buick Allure?

The bolts holding the pump to the engine are removed and the pump is pulled out. The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.

How do you replace a water pump in a radiator?

Make sure that the holes for the bolts on the new pump are lined up with the holes on the motor. Replace the six bolts on the new water pump. Use a torque wrench to tighten them to 9 ft.-lbs. of torque. Replace the timing belt on the engine and pour the coolant from its container back into the radiator.

Navigation