Where is the alternator located on a Mazda?
A defective alternator can cause damage to the battery and may leave you stranded on the side of the road. The alternator on the Mazda car is located on the left (passenger-side) front of the engine, below the intake manifold duct.
How do you remove an alternator from a car?
If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt.
Do you need to remove serpentine belt to change alternator?
As you loosen the bolts, the alternator will slide in the bracket under the tension of the belt. You may not need to remove the serpentine or accessory belt if it’s not damaged.
What is the serpentine belt on a Mazda 6?
The serpentine belt in the Mazda 6 is a single, continuous belt that drives the crankshaft of the engine along with the alternator, water pump, air conditioner and the power steering pump.
If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt.
How to troubleshoot an alternator and charging system problem?
If necessary, adjust the belt with the help of your car owner’s manual or repair manual. Inspect the belt for signs of cracks, cuts, shiny spots, deterioration or other signs of wear or damage. Change the belt and belt tensioner at the manufacturer’s recommended interval. 2. Check for Wiring Problems
How often do you replace the serpentine belt on a Mazda?
Reinstall the access panel cover. Reinstall the wheel and lower the vehicle. Mazda recommends that the serpentine belt is replaced every 35,000 miles. The serpentine belt may also be referred to as the drive belt, accessory belt, or the alternator/air conditioner belt.
What kind of belt does a Mazda 3 use?
In this guide, you will find instructions on how to change the serpentine belt (engine drive belt) on Mazda’s four-cylinder engine. The 2.5L is one of the most popular engines Mazda made, and it is found on several models, including Mazda 3, 5, 6, and even Tribute.
What’s the best way to replace an alternator?
Replacing the alternator is a repair that the average home mechanic can perform in an afternoon using basic hand tools. Disconnect the battery at the positive terminal by turning the bolt counterclockwise. Disconnect the alternator’s terminal by turning the nut counterclockwise and removing the loop from the terminal bolt.
Where is the accessory drive belt on an alternator?
Place the accessory drive belt over the alternator’s drive shaft. Put the top bolt of the alternator in place and turn the adjuster until the accessory drive belt is nice and tight. Tighten the bolt with some force. You don’t want the belt to come off while driving. Reattach the negative cable to the battery terminal.
Where does the battery cable go on an alternator?
Bolt the battery cable onto the alternator and slip it into place on the lower mounting bracket. Install the lower pivot bolt and tighten it snugly. Bolt the upper tensioner bracket to the engine and the alternator. Slip the alternator belt onto the pulley. Tighten the 12-mm tensioner bolt until the alternator belt is tight.
What to do about a 1999 Mazda Miata?
MAZDA MIATA 1999-04 Procedure Explanation Pages Must Be Used with the Above Text for an Accurate Damage Report. Comments or suggestions? Need assistance? Call 1-800-854-7030 or 858-578-6550. Ext. 8220. Fax 1-888-256-7969 or 858-549-0629. madpl1_g01_233 Page 233—April 22, 2004—13:34:01—Version Manufacturer MAZDA MIATA 1999-04 SPECIAL CAUTIONS
Where is the paint code on a Mazda Miata?
Manufacturer advises that some new fasteners must be used whenever old fasteners are loosened or removed. PAINT CODE LOCATION Paint code located on left lock pillar.
What kind of fuel economy does a Mazda Miata have?
1999-00 To VIN 138751 NC10-69-044 From VIN 138751 NC49-69-C31A 2001-04 NC72-39-044 4Label, Fuel Economy 1999-02 Man Trans 5 Speed NC72-69-042 6 Speed NC76-69-042 Auto Trans NC77-69-042 2003 Man Trans NC73-69-042 Auto Trans NC81-69-042 2004 Man Trans NC73-69-042B Auto Trans NC81-69-042B
What’s the best way to remove an alternator?
Remove the upper alternator tensioner and bracket using a 14-mm socket and socket wrench. Rotate the alternator slightly clockwise to loosen the belt and remove the belt from the alternator pulley. Remove the lower alternator pivot bolt using a 14-mm socket and socket wrench.
How do you remove a pivot bolt from an alternator?
Rotate the alternator slightly clockwise to loosen the belt and remove the belt from the alternator pulley. Remove the lower alternator pivot bolt using a 14-mm socket and socket wrench.
How do you adjust the tension on an alternator?
Wrap the drive belt around the alternator pulley wheel (groove side down), then press the tension pulley arm and slide the belt back under the idle pulley wheel. Release the tension arm and the belt will automatically adjust to the proper tension.