Where can I find E38 ECM connector pinouts?

E38 ECM Connector Pinouts WWW.LT1SWAP.COM [ HOME ] [ PCM PROGRAMMING ] [ WIRE HARNESS INFO ] [ Active Fuel Management DELETE ] Visit my Facebookpage for a lot of New Pictures & Harness Guides YouTubechannel for How To videos – E-Mail: [email protected] Below are the ECM Connectors for 2008 vortec 5.3L harness.

Where do the wires go from ECM to plug?

WIRES THAT ARE NOT HIGHLIGHTED REMAIN UN TOUCHED. THEY WILL GO DIRECTLY FROM ECM TO A PLUG, (SENSOR, SWITCH, DEVICE ETC.) OEM#:13580788 73-Way Female MX123 34566 Series, Color Black These Pinouts are for GAS engines V8

What kind of ECM do I need for Vortec 5.3L harness?

Below are the ECM Connectors for 2008 vortec 5.3L harness. Should be similar for 4.8L 6.2L applications. BLOCKS HIGHLIGHTED LIKE THIS, ARE WIRES THAT ARE NEEDED, AND GO TO EXTERNAL CONNECTION FOR STAND ALONEI have also highlighted the 6 wires used to connect to the gas pedal.

What are the pin out charts for PCM?

1998-99 PCM Connector Pin Out Charts (GM 4.3L, 5.0L, 5.7L). Each connector can be identified as: C1 Blue (32 Pin Connector). C2 Red (32 Pin Connector). C3 Clear -or Grey- (32 Pin Connector). C4 Black (24 Pin Connector). Contents of this tutorial: C1 Blue. C2 Red. C3 Clear -or Grey-. C4 Black.

Where do I get the PCM wiring harness?

Typically, the conversion installer will get the factory engine harness from the donor vehicle. This will include every wire and connector between the PCM and the engine’s sensors (Oxygen, Throttle Position, Crank Position, etc.) and the active systems (coil triggers, injectors, IAC, etc.).

How can I Check my ECM ground circuit?

Disconnect the ECM harness connectors. Using a 12-volt test light connected to 12-volts, check each of the ECM ground circuits in ECM harness connector. Did the test light illuminate for each cavity?

What should I do if I suspect a faulty ECM?

Performing a visual inspection is something that anyone can do right from home and is one of the first tests you should perform if a faulty ECM is suspected as ECM plays a very serious role in your vehicle.

Do you need to remove wires from PCM connectors?

BLOCKS HIGHLIGHTED LIKE THIS, ARE WIRES THAT CAN BE REMOVED FROM PCM CONNECTORS, NOT NEEDED. Note: Removing all of these will result in a non-emissions friendly harness. If requirements are for 4 oxygen sensors, EVAP system, then you will not want to remove those components.

What are the pinouts for an E38 fuel pump?

Low Reference – APP Sensor Pin F X109 C6 31 0.35 TN/BK 6049 Low Reference – Fuel Tank Pressure Sensor Pin A, Fuel Pump Sender Assembly Pin B 32 0.35 L-BU 1162 APP Sensor 2 Signal – APP Sensor Pin B X109 C2 33 0.35 GY 2709

What kind of pin do you use to locate a pin?

A button or lever releases the pin for removal. Round locating pins use a round, tapered tip. They are often used in conjunction with a diamond-tipped pin, and a bushing as well, to align components on multiple axes. T-pins are similar to L-pins, but with a T-shaped grip and the option of having a locking mechanism interacting with the bushing.

What kind of pins do you use for quick release?

Quick-release pins (ball lock) use a spring-loaded steel ball to provide positive gripping action. A button or lever releases the pin for removal. Round locating pins use a round, tapered tip.

Navigation