What kind of torque does a Jeep Cherokee have?
Each Jeep engine has unique head bolt torque specifications. Head bolts hold the engine head onto the engine block and resist the force of engine compression. There are two key pieces of information with each torque specification: the sequential order for tightening the set of bolts and the amount to tighten the bolts at each tightening step.
What kind of engine does a 1998 Jeep Cherokee have?
The 1998 Jeep Cherokee was available with a 6-cylinder 4.0 liter engine. As with all engines, rebuilding the 4.0 liter requires careful attention to detail. One of the most important and commonly overlooked details is the engine’s torque specifications.
What are the specs for a Jeep Cherokee?
Control arms lengths are important for castor and location of axle in the wheel wells. At 3″, you will be ok with stock arms, just expect the axle to move back toward the cab a little and some minor bumpsteer. XJ Cherokee Specs!
How big are the head bolts on a jeep?
Bolts are tightened in these steps: first to 22 ft.-lb., second to 45 ft.-lb., third to 45 ft-lb. again, fourth (bolt 11) to 100 ft.-lb., and fifth, all other bolts to 110 ft.-lb. There are two rows of four head bolts on each bank of the V6 engine. Each bank is tightened using the same steps and specifications.
What are the torque specifications of a Jeep Cherokee?
31.18 XJ – FRONT Brake Hose to Caliper Inlet Fitting Bolt Type: Bolt 27.12 XJ – Brake Pedel Pivot Pin Nut
What kind of bolts are in a Jeep Cherokee?
27.12 XJ – Brake Pedel Pivot Pin Nut Type: 7.5 10.17 XJ – REAR Wheel Cylinder Mounting Bolts Type: Bolt 40.67 XJ – FRONT Caliper Mounting (Guide) Pins Type: Bolt 104.4 XJ – FRONT Caliper Achor Plate Bolts Type: Bolt 40.67 XJ – REAR Crossmember to Chassis Sill Bolts Type: Bolt
What kind of drain plug does a Jeep Cherokee use?
XJ – Transfer Case Drain Plug Type: Bolt Head: Hexagon 20 240 27.12 XJ – MANUAL Transmission Drain Plug Type: Bolt Head: Hexagon Drive Shaft To Transfer Case Assembly 22 264 29.83 XJ – Driveshaft to Transfer Case Flange Bolts Type: Bolt Head: Hexagon Drive Shaft To Transfer Case Assembly 35 420 47.45 XJ – FRONT Universal Joint Flange Nut Type:
What was the lifespan of the Jeep Cherokee?
That is a remarkable 18 year lifespan in which 2,884,172 Jeep Cherokees rolled off the assembly line! Originally designed and built by AMC, Chrysler continued the same design when they bought AMC in 1987. Anyways, the Cherokee was the icon of compact SUVs which led to a market full of those who tried to imitate it.
How to install cylinder head on Jeep 4.0L?
Apply sealant to both sides of new cylinder head gasket. Install new gasket with the word “TOP” upward. Ensure all holes are aligned. 2) Install cylinder head. Apply sealing compound to threads of cylinder head bolt No. 11 prior to installation. See Fig. 3. Install head bolts. lbs. (149 N.m) on 4.0L or 85 ft. lbs. (115 N.m) on 4.2L models.
What are the torque specifications for an AMC 4.0L torkspec?
44.74 Type: Bolt 80 960 108.47 Type: Bolt 110 1320 149.14 3 Step: 22; 45; 110-NOTE: Left Front Bolt Final=100FtLbs Type: Bolt 100 1200 135.58 Left Front Bolt ONLY – 3 Step: 22; 45; 100 Type: Bolt 17
Each Jeep engine has unique head bolt torque specifications. Head bolts hold the engine head onto the engine block and resist the force of engine compression. There are two key pieces of information with each torque specification: the sequential order for tightening the set of bolts and the amount to tighten the bolts at each tightening step.
The 1998 Jeep Cherokee was available with a 6-cylinder 4.0 liter engine. As with all engines, rebuilding the 4.0 liter requires careful attention to detail. One of the most important and commonly overlooked details is the engine’s torque specifications.
Bolts are tightened in these steps: first to 22 ft.-lb., second to 45 ft.-lb., third to 45 ft-lb. again, fourth (bolt 11) to 100 ft.-lb., and fifth, all other bolts to 110 ft.-lb. There are two rows of four head bolts on each bank of the V6 engine. Each bank is tightened using the same steps and specifications.
44.74 Type: Bolt 80 960 108.47 Type: Bolt 110 1320 149.14 3 Step: 22; 45; 110-NOTE: Left Front Bolt Final=100FtLbs Type: Bolt 100 1200 135.58 Left Front Bolt ONLY – 3 Step: 22; 45; 100 Type: Bolt 17
How much torque does a Wrangler YJ engine have?
4.0L & 4.2L Engine Torque Specs Description Specification Camshaft Sprocket Bolt 50 ft-lbs Crankshaft Pulley To Vibration Dampener 20 ft-lbs Cylinder Head Bolts 4.2L 85 ft-lbs Cylinder Head Bolts 4.0L First 22 Then 45 Then 45 Then 100 ft-lbs
How much torque does a 4.0 liter engine have?
As with all engines, rebuilding the 4.0 liter requires careful attention to detail. One of the most important and commonly overlooked details is the engine’s torque specifications. Tightening a bolt too much can damage the component it is designed to secure, and may even break the bolt off inside of the engine block.
How much torque does a YJ engine have?
2.5L Engine Torque Specs Description Specification Camshaft Sprocket Bolt 80 ft-lbs Crankshaft Pulley To Vibration Damper Bo 20 ft-lbs Cylinder Head Bolts (1987-1988) Bolt 8 = 75 ft-lbs Rest = 85 ft-lbs Cylinder Head Bolts (1989-1995) Bolt 8 = 100 ft-lbs Rest = 110 ft-lbs
How much horsepower does a jeep 4.0L have?
Some of the popular builds you’ll see are 4.7-liter stroker motor which will make around 210hp and upwards of 300lb-ft of torque. There are quite a few people who have turbocharged these engines which is interesting because of how wild the 4.0 sounds when you add some boost to it.
27.12 XJ – Brake Pedel Pivot Pin Nut Type: 7.5 10.17 XJ – REAR Wheel Cylinder Mounting Bolts Type: Bolt 40.67 XJ – FRONT Caliper Mounting (Guide) Pins Type: Bolt 104.4 XJ – FRONT Caliper Achor Plate Bolts Type: Bolt 40.67 XJ – REAR Crossmember to Chassis Sill Bolts Type: Bolt
How does the head bolt work on a jeep?
Each Jeep engine has unique head bolt torque specifications. Head bolts hold the engine head onto the engine block and resist the force of engine compression.
XJ – Transfer Case Drain Plug Type: Bolt Head: Hexagon 20 240 27.12 XJ – MANUAL Transmission Drain Plug Type: Bolt Head: Hexagon Drive Shaft To Transfer Case Assembly 22 264 29.83 XJ – Driveshaft to Transfer Case Flange Bolts Type: Bolt Head: Hexagon Drive Shaft To Transfer Case Assembly 35 420 47.45 XJ – FRONT Universal Joint Flange Nut Type:
Apply sealant to both sides of new cylinder head gasket. Install new gasket with the word “TOP” upward. Ensure all holes are aligned. 2) Install cylinder head. Apply sealing compound to threads of cylinder head bolt No. 11 prior to installation. See Fig. 3. Install head bolts. lbs. (149 N.m) on 4.0L or 85 ft. lbs. (115 N.m) on 4.2L models.
Each Jeep engine has unique head bolt torque specifications. Head bolts hold the engine head onto the engine block and resist the force of engine compression.
What kind of engine does a 1997 Jeep Cherokee have?
The Jeep Cherokee (XJ) 2.5 TD has a Inline 4, Diesel engine with 2499 cm3 / 152.5 cu-in capacity. How many horsepower (hp) does a 1997 Jeep Cherokee (XJ) 2.5 TD have? The 1997 Jeep Cherokee (XJ) 2.5 TD has 116 PS / 114 bhp / 85 kW.
When did the Jeep Cherokee 2.5 TD come out?
For stopping power, the Cherokee (XJ) 2.5 TD braking system includes Vented Discs at the front and Drums at the rear. The Cherokee (XJ) model is a car manufactured by Jeep, sold new from year 1997 until 2001, and available after that as a used car.
When did the torque specs come out for the Wrangler?
The torque specs needed to rebuild this inline six if the need should arise. This engine was used from 2003 to 2006 and served as the successor to the 2.5 liter engine. The oxygen sensors require a special socket to be removed due to the wires. Also be sure to note that there are different specs for each set of bolts.
Where can I find torque specifications repair guide?
Once you sign in, follow these instructions to access our Repair Guides. Add your vehicle in Manage My Vehicles. Enter your vehicle details. Click the “View More” button, and then click “Vehicle Repair Guides.” Select the chapter “Torque Specifications Repair Guide”.
How to set torque on a jeep 3.7L cylinder head?
Re: I want torque setting for jeep 3.7l on cylinder head Hi there: Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows: Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm) Step 2: Bolts 1-10 verify torque without loosening Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm) Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
What are the torque settings for cylinder head bolts?
You can’t post conmments that contain an email address. Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.
How many horsepower does a 1993 Jeep Cherokee have?
Jeep Cherokee 2.5 Jamboree (man. 5) , manufactured or sold in 1993, version for Europe (since mid-year 1993) gasoline (petrol) engine with displacement: 2471 cm3 / 150.8 cui, advertised power: 90 kW / 121 hp / 122 PS ( DIN ), torque: 200 Nm / 147 lb-ft, more data: 1993 Jeep Cherokee 2.5 Jamboree (man. 5) Horsepower/Torque Curve
As with all engines, rebuilding the 4.0 liter requires careful attention to detail. One of the most important and commonly overlooked details is the engine’s torque specifications. Tightening a bolt too much can damage the component it is designed to secure, and may even break the bolt off inside of the engine block.