What is fuel pressure on international 4300 MaxxForce 466?
I have a 2011 International 4300 Maxxforce 466. Just did a PM service, now a hard start when code .need to starting fluid to initially get it running. Code pops up, SPN 931 FMI 11. I check fuel pressure on the computer, 74 psi.
What should the oil pressure be on a MaxxForce 13?
Not really sure why someone would take the filter out and leave it out. Minimum safe oil pressure is 10 psi. 15 psi is fine. It is a bit lower than what is “typical”. Most are around the 20 psi mark. Minimum safe oil pressure is 10 psi. 15 psi is fine.
What’s the fuel pressure on an international 4300?
I check fuel pressure on the computer, 74 psi. A wet gauge is between 80 and 90. Sometimes this code pops up active when cycling the ignition, then goes inactive during crank. Rechecked fuel filter – ok, removed pump to clean the bottom prescreen, which was not very dirty.
What should the ICP be on a MaxxForce DT?
At an idle the ICP has to be around 800 psi. The maximum depending on the load and RPM can get as high as 4500 psi. That is a lot of oil pressure to contain day in and day out. Something has got to give as they say and it happens.
How many horsepower does an international MaxxForce DT have?
Only 154,000 Miles – Ran Like New Engine Serial # 466HM Engine Family # A215 Engine HP: 215 Engine Model: Maxxforce DT Displacement: 7…. See More Details (USED) 2015 International 4300 – Maxxforce DT Diesel Engine.
Are there any 2011 International 4300 trucks for sale?
2011 INTERNATIONAL 4300, STOCK # 06791 2011 INTERNATIONAL 4300, NON CDL, AUTO, LOW MILE, 16 FT. UTILITY BODY & GATE TRUCK FOR SALE MX DT 466 @225HP (11… Commercial Truck Trader Disclaimer: The information provided for each listing is supplied by the seller and/or other third parties.
What kind of harness does MaxxForce DT466 use?
(USED) 2014 INTERNATIONAL DURASTAR 4300-COMPLETE ENGINE WIRING HARNESS FOR MAXXFORCE DT466. INCLUDES ALL PLUGS FROM ECM TO CAB. P/N 3864356F91 To find out more about this part, give us a call.
Is there an electrical fault on my international MaxxForce 7?
We replaced the long block on a 2011 international Maxxforce 7. We finally got it all back together and went to try and fire it up and basically got nothing but an electrical fault on the dashboard and the truck doesn’t do anything. I can hear the relays clicking but getting nothing. 1HTJTSKL5BH359690. That is a cluster fault .
What are the fault codes for International trucks?
International Trucks Fault Codes List (DTCs) for Model: 3200, 4100, 4300, 4400, 7300, 7400, 7500, 7600, 7700, 8500, 8600, BE 200, CE Bus, CXT, DuraStar, LoneStar, MXT, ProStar, RXT, TranStar, WorkStar. See also: International Trucks Service Repair Manuals PDF
What’s the year of the International MaxxForce 7?
Electrical fault on a 2011 international maxxforce 7. 2011… Electrical fault on a… Electrical fault on a 2011 international maxxforce 7 Mechanic’s Assistant: What’s the make/model/year of your truck? Engine type? Mechanic’s Assistant: Are you fixing your truck yourself? What have you tried so far?
Do you have cookies on international MaxxForce 7?
By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them. Electrical fault on a 2011 international maxxforce 7. 2011…