What are the fault codes for Cummins ISX engines?
784 Adaptive Cruise Control Mode – Data Erratic, Intermittent, or Incorrect 1239 Accelerator Pedal or Lever Position Sensor 2 Circuit – Voltage Above Normal or Shorted to High Source 1241 Accelerator Pedal or Lever Position Sensor 2 Circuit – Voltage Below Normal or Shorted to Low Source
When does an ISX fault code become active?
The pressure in the intake manifold exceeded the maximum allowable value for a given engine rated power. This DTC becomes active when the pressure in the intake manifold exceeds the maximum allowable value for a given engine power rating. ISF 2.8, ISF 3.8, ISB, ISC, ISL, ISLe , ISDe , QSB 3.3
When did the ISX engine codes come out?
These codes pertain to the ISX engines built between 2007 and 2010. These engines are easily identified by having a DPF and regen on a regular basis. These codes do NOT pertain to engines using DEF. 111 Engine Control Module Critical Internal Failure – Bad Intelligent Device or Component
What’s the serial number on a Cummins Peterbilt?
2011 Peterbilt; Cummins ISX engine. Husband stop to nap; woke up and tried to start engine; Engine light came on and no power. I do have serial … read more 2006 Peterbilt ISX trouble code 245….what caused this malfunction? 2006 Peterbilt ISX trouble code 245….what caused this malfunction? Fan is on full-time now. … read more
Which is the most severe fault code for Cummins?
352 Sensor Supply 1 Circuit – Voltage Below Normal or Shorted to Low Source 386 Sensor Supply 1 Circuit – Voltage Above Normal or Shorted to High Source 415 Engine Oil Rifle Pressure – Data Valid But Below Normal Operating Range – Most Severe Level 418 Water in Fuel Indicator – Data Valid But Above Normal Operating Range – Least Severe Level
What is the Regen code for a Cummins Engine?
These engines are easily identified by having a DPF and regen on a regular basis. These codes do NOT pertain to engines using DEF. 111 Engine Control Module Critical Internal Failure – Bad Intelligent Device or Component 115 Engine Magnetic Speed/Position Lost Both of Two Signals – Data Erratic, Intermittent, or Incorrect
What are the fault codes for Cummins oil pressure sensor?
A low signal voltage or an open circuit is detected in the oil pressure sensor circuit. The ECM determines that the oil pressure sensor signal voltage is less than 0.25 VDC for more than 16 seconds. ISF 2.8, ISF 3.8, ISB, ISC, ISL, ISLe , ISDe , QSB 3.3 A high signal voltage or an open circuit is detected in the coolant temperature sensor circuit.
Where is the WiF sensor on a Cummins ISX?
Hello Sawguy, the WIF sensor is located on the bottom of the fuel filter. Should be the only item on the fuel filter housing that has a wire going to it. sawguy Thanks this.
What is the SPN code for a FMI Sid?
SPN FMI PID/SID PID/SID ID FLASH CODE FAULT DESCRIPTION 634 4 SID 40 1321 Constant Throttle Valve Circuit Failed Low 634 3 SID 40 1321 Constant Throttle Valve Circuit Failed High 634 5 SID 40 1321 Constant Throttle Valve Circuit Failed Open 636 1 SID 21 1235 Crankshaft Position Sensor Signal Voltage Too Low
What is the engine coolant sensor code in FMI?
110 2 PID 110 1212 Engine Coolant Sensor (OUT), General Temp. Plausibility Error SPN FMI PID/SID PID/SID ID FLASH CODE FAULT DESCRIPTION 132 7 PID 132 1213 Intake Air Throttle Valve Closure Detection- Positive Torque 132 14 PID 132 1213 Intake Air Throttle Valve Closure Detection -Braking Condition