How to reset the PassLock 3 security system?
Turn the key to ON but do not start the engine. The SECURITY light will turn on and stay on. 3. Wait 10 minutes or until the SECURITY light to turn off. 4. Turn the key to OFF for 5 seconds. 5. Turn the key to ON but do not start the engine. The SECURITY light will turn on and stay on. 6. Wait 10 minutes or until the SECURITY light to turn off. 7.
How long does it take to reset Passkey III?
Passkey III Reset procedure. Make sure the battery if fully charged because this procedure may take up to 30 minutes and you cannot start the vehicle during this time. If you’re adding a new key to the system, you MUST have all the older keys with you. All previously learned keys will be erased from the system as soon as you program the first key.
How to turn off GM PassLock security Telltale?
Here it is in it’s entirity. Turn ON the ignition, with the engine OFF. Attempt to start the engine, then release the key to ON (vehicle will not start). Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF. Turn OFF the ignition, and wait 5 seconds .
How to bypass vats, Passkey and PassLock security systems in GM?
It can be VATS, Passkey or Passlock anti theft system that is going bad causing your issue. I am going to share a secrete with you on how you can bypass these systems with very little effort. This is a really unique security system bypass kit that you can use to override your current factory theft system on your GM vehicle.
How do you get a GM passkey 3?
Try the following procedure which is specifically for GM Passkey 3. 1. Insert a master key (black head) into the ignition switch. 2. Turn to the On position without starting the engine. The security light should illuminate and stay on. 3. Wait approximately 10 minutes or until the security light turns off.
Turn the key to ON but do not start the engine. The SECURITY light will turn on and stay on. 3. Wait 10 minutes or until the SECURITY light to turn off. 4. Turn the key to OFF for 5 seconds. 5. Turn the key to ON but do not start the engine. The SECURITY light will turn on and stay on. 6. Wait 10 minutes or until the SECURITY light to turn off. 7.
What happens when I Turn on Passkey 3?
Whats interesting is with Passkey 3 enabled there should be no power to the starter in addition to cutting off the pulse width modulation to the fuel injection system. So the engine should not even start.
How to turn off security light on passkey 3?
Try the following procedure which is specifically for GM Passkey 3. 1. Insert a master key (black head) into the ignition switch. 2. Turn to the “On” position without starting the engine. The security light should illuminate and stay on. 3. Wait approximately 10 minutes or until the security light turns off.
Can You disable the PassLock on a GM car?
The following instructions will allow you to disable the PassLock security in quite a few GM Vehicles. •This will allow you to install a remote starter and not have to purchase a bypass. •Avoid Costly repairs for an already broken PassLock System.
What to do if your car won’t start at PassLock?
A red (or yellow) “security” warning light will stay illuminated and the engine will either a) never start or b) start for a moment and then shut down. A temporary fix is to leave your key in the ignition, at the “auxiliary” position for about 10-15 minutes until the security light shuts off.
How to bypass the PassLock sensor on a 2002 Pontiac Grand Am?
This web page will guide you through the steps necessary to bypass the “Passlock Sensor” on a 2002 Pontiac Grand Am, and keep the “SECURITY” light off forever. The steps necessary are similar on the other models listed above. There are generally only minor differences in how to get the radio out to get to the wires.
A red (or yellow) “security” warning light will stay illuminated and the engine will either a) never start or b) start for a moment and then shut down. A temporary fix is to leave your key in the ignition, at the “auxiliary” position for about 10-15 minutes until the security light shuts off.
This web page will guide you through the steps necessary to bypass the “Passlock Sensor” on a 2002 Pontiac Grand Am, and keep the “SECURITY” light off forever. The steps necessary are similar on the other models listed above. There are generally only minor differences in how to get the radio out to get to the wires.
How do I reset the PassLock on my car?
1. Insert the master key with the black head into the ignition lock cylinder 2. Turn the key to ON but do not start the engine. The SECURITY light will turn on and stay on. 3. Wait 10 minutes or until the SECURITY light to turn off. 4. Turn the key to OFF for 5 seconds. 5. Turn the key to ON but do not start the engine.
How to troubleshoot a GM 3.8L no start?
It’s been my experience that the majority of the Cranks but Does no start conditions I’ve troubleshooted and repaired (on GM 3.8L equipped vehicles) had their root cause in the ignition system. So, my recommendation to you is to check for spark at all of the spark plug wires with a spark tester.