How much torque does a Caterpillar 3406 diesel engine have?
CATERPILLAR 3406 Essential Diesel Engine Bolt Tightening Torques. 1 Step 1 = 190 lb.ft, 260 Nm. 2 Step 2 = plus 120 degrees. CAT 3406 Connecting Rod Bolts. 3 Step 1 = 60 lb.ft, 80 Nm. 4 Step 2 = plus 120 degrees. CAT 3406 Cylinder Head Bolts. 5 Step 1 = 200 lb.ft, 270 Nm.
What are the dimensions of a cat 3406?
CAT 3406 Dimensions approx: length = 1535 mm, 60.4 in width = 954 mm, 37.5 in height = 1178 mm, 46.4 in Click for CAT 3406 engine manuals and specs. CAT 3406 Weight approx: 1586 Kg, 3489 lb Click for CAT 3406 engine manuals and specs.
Which is harder motor mount bolts or garden variety bolts?
Bolts that hold on bumpers, trailer hitches, motor mounts, cylinder heads, etc. are typically a lot tougher than a garden variety bolt; hence they have a higher ‘grade’ or ‘class’ and are marked appropriately. Higher grade/class matching nuts are marked as well.
What is the compression ratio on a cat 3406?
CAT 3406 Compression ratio Check piston part number 7C2888 Crown = ratio 16.25:1 1352837 Crown = ratio 16.25:1 149-5566 Crown = ratio 16.25:1 180-7352 Crown = ratio 16.6:1 Click for CAT 3406 engine manuals and specs.
Where can I find the latest torque specs?
Find the most up-to-date torque spec listings in electronic format. FelPro-Only.com is your convenient source for advanced sealing information. It’s the place to learn and share “tricks of the trade,” find proper diagnosis and installation instructions, and enjoy easy access to parts reference.
What are the torque specifications for a car?
The specified amount will normally be in 30° increments. Turns of 120° or 180° are preferred. Turns of 120° or 180° are easily measured by the points of the hex head of the fastener. Lubrication may be specified in order to reduce the effort that is required for the final turn.
What kind of camshafts does Elgin industries make?
Each Elgin PRO STOCK camshaft is precision-machined and hardened from a premium-quality blank manufactured in certified U.S. facilities. As a leading supplier of performance, standard automotive and RV camshafts, Elgin enjoys a well-earned reputation for quality, performance and value.
How much torque does a Caterpillar C15 engine have?
CATERPILLAR C15 Essential Diesel Engine Bolt Tightening Torques CAT C15 Main Bearing capscrews step 1 = 95 Nm, 70 lb.ft step 2 = 260 Nm, 190 lb.ft
How big is the engine in a cat 3304?
CAT 3304 Displacement, bore and stroke Displacement 7.0 liter 427 CID Bore 4.75″ 120.65 mm Stroke 6.0″ 152.4 mm Click for CAT 3304 and CAT 3306 engine manuals and specs
Where is the timing bolt in a Caterpillar diesel engine?
11. Put the timing bolt in the timing hole in the flywheel housing. Rotate the crankshaft counterclockwise (as seen from the flywheel end of the engine) until the fuel pump camshaft is tight against timing pin (2). This removes gear clearance from the drive train.
How to preload gears on an advanced timing unit?
If you put the advance on with the pump and engine pined,then the timming is retarded.If you break the 6 3/8 bolts loose on the advance and pin the pump and rotate the motor about 40 degrees counter clockwise and then back to 0 it will preload the gears, then it should be dead on.
What happens when the torque is too much?
Too much tension on the bolt will cause the bolt to be stretched beyond the point of yield. The bolt will be permanently stretched. The bolt will loosen the grip on the parts that are being fastened. If the bolt is tightened again, the bolt will break. Do not reuse bolts that have been permanently stretched.