How do you reset the TPMS light on a 2013 Subaru Outback?

How do you reset the TPMS light on a 2013 Subaru Outback?

Start the engine and idle for 20 minutes while the system records and stores the new PSI of each wheel. Drive the car at 25 mph or greater for another 30 minutes. If the low pressure light is still illuminated try disconnecting the battery cable and reconnecting it to restore settings.

How do you clear the TPMS light on a Subaru?

Drive the car at 50 mph for about 10 minutes. Without starting the car, turn the key to the β€œOn” position. Press the TPMS reset button and hold it until the light blinks three times, then release it. Start the car and let it run for 20 minutes to reset the sensor.

How do you reset the TPMS on a Subaru Outback?

To reset the tire pressure monitor or tpms system in your 2018 subaru outback vehicle, turn the ignition key to the “on” position and depress the tpms button, usually located under the dash, until the tpms light blinks several times.

Where is the TPMS reset button on a 2009 Subaru Outback?

To reset the TPMS warning, park the car on a flat surface and using a gauge, make sure tires are inflated to a PSI of 35 in the front and 33 PSI in the rear. With the doors locked and windows rolled up, turn the key in the ignition to the “on” position and locate the reset button below the steering wheel.

When to clear the TPMS warning light on a Subaru Outback?

TIP: The TPMS warning light in your Subaru Outback should be cleared. However, if the light remains illuminated, keep in mind after tires are inflated/deflated, the outdoor temperature affects how fast the air in the tires will adjust to the proper temperature, this could take a day, 2 or 3, simply be patient and give the tires time to adjust.

What should the tire pressure be in a Subaru Outback?

Make sure the spare has the correct amount of air as well. F ill each tire to the recommended PSI/Air Pressure Levels. Do not forget the spare. Normally 32lbs in the Front tires and 30lbs in the Back. Drive the vehicle for 25/mph or more for a few minutes. TIP: The TPMS warning light in your Subaru Outback should be cleared.

How does the tire pressure monitor work on a Subaru Legacy?

The tire pressure monitor system (TPMS) on the 2005 – 2013 Subaru Legacy and Outback checks the tire pressures of all four road wheels when the vehicle is driven at speeds above 25 mph (40 km/h), and warns in the event of a loss of pressure by means of a low tire pressure warning light.

When does the TPMS warning light turn off?

After adjusting air pressure, drive the vehicle at 25 mph (40 km/h) or more to start TPMS re-checking of the tire inflation pressures. The warning light should turn off in a few minutes. If the warning light is still on after adjusting tire pressure, check for a damaged tire and repair as necessary.

Why is the TPMS not working on my Subaru Outback?

Be careful not to damage the airbag system wiring harness when servicing the TPMS control module. Under the following conditions, the system may not function properly: If tire pressures are incorrect. If tires are damaged or punctured. Air pressure sensor malfunction. Air pressure sensor is out of battery power.

When to check tire pressure on Subaru Outback?

If this light does not illuminate briefly after the ignition switch is turned ON or the light illuminates steadily after blinking for approximately one minute, you should have your Tire Pressure Monitoring System checked at a SUBARU dealer as soon as possible.

The tire pressure monitor system (TPMS) on the 2005 – 2013 Subaru Legacy and Outback checks the tire pressures of all four road wheels when the vehicle is driven at speeds above 25 mph (40 km/h), and warns in the event of a loss of pressure by means of a low tire pressure warning light.

What to do if your Subaru has a low tire pressure light?

Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. If the light illuminates steadily after blinking for approximately one minute, promptly contact a SUBARU dealer to have the system inspected. The tire pressure monitoring system is NOT a substitute for manually checking tire pressure.

Posted In Q&A