How do you remove the ignition switch from a 1999 Pontiac Grand Am?
How to Remove the Ignition Switch in a 1999 Pontiac Grand Am. Disconnect the negative battery cable from the battery terminal with the appropriate sized socket and ratchet. Remove the trim piece surrounding the steering column. Unscrew the three Torx screws on the bottom of the piece and unhook the lower piece of trim from the upper piece.
How to replace GM PassLock ignition key lock cylinder?
Press the small release tab (see pictures) While turning key to the ON Position Installation is the reverse of the above procedures, see below for the relearn procedure Clear all Diagnostic Trouble Codes (DTC). Record and/or repair your DTCs before clearing. You can clear the codes by disconnecting the battery for 10 minutes.
Where is the ignition button on a Pontiac?
Locate the locking button located on the backside of the ignition cylinder housing. Push the button and then pull the lock cylinder away from the column. Unscrew the ignition switch from the steering column using the Phillips head screwdriver.
How to test a new ignition lock cylinder?
Step 10: Test the operation of the new ignition lock cylinder. Before you reconnect the battery, make sure your new ignition lock cylinder moves to all four positions with the new key. Test this function three to five times to verify the repair was completed correctly.
Where is the neutral switch on a car?
A neutral safety switch works just like a clutch switch except that it keeps an automatic transmission from starting in gear. The neutral safety switch will allow the engine to start with the transmission selector in park and neutral. The switch is located in two places on the vehicle.
How do you adjust a neutral ignition switch?
Adjusting the Switch by Sliding the Switch Loosen the switch’s mounting bolts just enough so that you can move the unit sideways. Ask an assistance to turn and hold the ignition key in the start position, as if trying to fire up the engine. Then, slide the switch towards the Park or Neutral position.
What was the ignition switch on a 2002 Pontiac Grand Prix?
This 2002 Pontiac Grand Prix had already been diagnosed with a faulty ignition switch. The faulty switch was not allowing the blower motor to operate properly. Click here to view that post.
How to remove the ignition switch in a 1997 Pontiac Bonneville?
Unplug the yellow wiring harness on the steering column with your hands, then unplug the remaining wiring on the column. Remove the ignition switch actuator rod from the ignition switch using the Phillips-head screwdriver. Remove the ignition switch from the car. How to Remove the Ignition Switch in a 1997 Pontiac Bonneville
How to remove the ignition switch in a 1999 Pontiac Sunfire?
Turn it to the “Run” position, but do not start the Sunfire. Locate the locking button located on the backside of the ignition cylinder housing. Push the button and then pull the lock cylinder away from the column. Unscrew the ignition switch from the steering column using the Phillips head screwdriver.
How to Remove the Ignition Switch in a 1999 Pontiac Grand Am. Disconnect the negative battery cable from the battery terminal with the appropriate sized socket and ratchet. Remove the trim piece surrounding the steering column. Unscrew the three Torx screws on the bottom of the piece and unhook the lower piece of trim from the upper piece.
Unplug the yellow wiring harness on the steering column with your hands, then unplug the remaining wiring on the column. Remove the ignition switch actuator rod from the ignition switch using the Phillips-head screwdriver. Remove the ignition switch from the car. How to Remove the Ignition Switch in a 1997 Pontiac Bonneville
Locate the locking button located on the backside of the ignition cylinder housing. Push the button and then pull the lock cylinder away from the column. Unscrew the ignition switch from the steering column using the Phillips head screwdriver.
Turn it to the “Run” position, but do not start the Sunfire. Locate the locking button located on the backside of the ignition cylinder housing. Push the button and then pull the lock cylinder away from the column. Unscrew the ignition switch from the steering column using the Phillips head screwdriver.
Why does my 1997 Pontiac Grand Am Not turn off?
This 1997 Pontiac Grand Am came in with the complaint that the ignition switch will not turn all of the way off. This causes two other problems. The key cannot be removed from the ignition lock cylinder and the ignition stays on enough for the systems not to shut down fully. The battery will go dead as a result.
What happens if the ignition switch goes out on a Pontiac?
The ignition switch on a Pontiac car Am is responsible for signaling the starter to turn over, which in turn starts the engine. If your Pontiac car Am’s ignition switch goes out, the starter doesn’t know when to engage and the Pontiac car Am will not start.
How do you remove ignition switch from car?
Insert a straightened out paperclip into the slot just to the left of the key cylinder. This will lock the cylinder from starting. Inserting your screwdriver into the cylinder and turn it as far as you can to the right. Pull on both the paperclip and the screwdriver to gently slide the switch out of its current position.
What to do if your Pontiac Grand Prix ignition switch stops working?
If playback doesn’t begin shortly, try restarting your device. Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. Check out my gear head channel.
How can I Turn Off the ignition without a key?
Be sure to make the hole large enough for you to insert your screwdriver, and drill to the back of the key slot. Insert a straightened out paperclip into the slot just to the left of the key cylinder. This will lock the cylinder from starting. Inserting your screwdriver into the cylinder and turn it as far as you can to the right.
What to do if your key is stuck in the ignition switch?
The key may be stuck in the ignition switch, but that shouldn’t stop you from turning it. If you don’t have a key, you will need to force the module to turn using a flathead screwdriver. Press the release pin inside the hole on the ignition module with a screwdriver.
How do you replace an ignition switch on a car?
Installing a Replacement Squeeze the release pin on the ignition switch so it’s flush with the side. The same release pin that stopped the switch from coming out now needs to be pressed in so you can slide the switch into place inside the ignition module. Slide the ignition switch into its hole.
Where is the release pin on an ignition switch?
The new or rebuilt switch should slide easily back into its hole on the steering column. Align the shape of the cylinder and the location of the release pin with the coinciding grooves in the ignition module.