Why does my Vito CDI 110 2000 shut off?
Hi My Vito CDI 110 2000 has Shut off Fault Code, Boost Pressure Code. 7.5a ECU Fuse causes grey smoke rough running when inserted. Merc Star Can not communicate with the CDI. Van starts and runs ok without the 7.5a fuse but in limp mode. Help.
Are there any problems with the Mercedes Vito?
Common Mercedes Vito ECU faults are. Start Error ( Immob Problem! ) If you need any help with these situations please contact me to save yourself alot of time and money! Sometimes you don’t need to change all of the ECU/WSP/Key if its only the ECU at fault!!:thumbsup:
Why does the Mercedes Vito go into limp mode?
Why does the Mercedes Vito van (112 CDI 638 chassis) go into limp mode after climbing over a long hill or while under load? The vacuum transducer and turbo pressure sensor were changed. There are a variety of reasons which can result in the Mercedes Vito engine going into a limp mode.
Why is the EDC light still on in my Mercedes Vito?
The glow plugs have current for the heat up process and then there is no currnet to them after a couple of seconds so performing properly but the light remains on. Two of the injectors were “chuffing” so I recut the seats, new copper washers and bolts and that appears to have fixed that problem but the EDC light remains on.
Is the starter on my Vito van working?
Starter Works Fine And When The Van Was Running It Was Running Fine .it Started To Take A While To Start And This Just Got Worse Over A Few Days Till It Would Not Start At All.
Hi My Vito CDI 110 2000 has Shut off Fault Code, Boost Pressure Code. 7.5a ECU Fuse causes grey smoke rough running when inserted. Merc Star Can not communicate with the CDI. Van starts and runs ok without the 7.5a fuse but in limp mode. Help.
Common Mercedes Vito ECU faults are. Start Error ( Immob Problem! ) If you need any help with these situations please contact me to save yourself alot of time and money! Sometimes you don’t need to change all of the ECU/WSP/Key if its only the ECU at fault!!:thumbsup:
The glow plugs have current for the heat up process and then there is no currnet to them after a couple of seconds so performing properly but the light remains on. Two of the injectors were “chuffing” so I recut the seats, new copper washers and bolts and that appears to have fixed that problem but the EDC light remains on.
Why does my Mercedes Benz Vito not start?
It turned out to be a broken wire to the injector. If the edc light is on then it will not start because it thinks there is a fault either with the wiring, air in the fuel, water in the fuel or lack of fuel pressure. Got my Vito back yesterday.
Are there any problems with the Mercedes Vito ECU?
Similar problem with the bas brake assist, had it diagnosed, replaced g force sensor and brake sensor, as that what fault codes came up, reset it, but light is back on!! Spent allot of money on original parts, and it is still the same, could it be the ECU it’s self?
Why is the EDC light always on in my Vito?
The wires in question run from a plug attached to something on the left had side of the engine (as you look at it) down by the alternator up to the wiring loom which runs across the rocker cover, not sure quite where they go to. Click to expand… Me too, i have same problem, EDC light always on.
What are the warning lights on a Mercedes Vito?
On start up I had two warning lights, glowplug light on (always) and the EDC light on (always). The glow plugs have current for the heat up process and then there is no currnet to them after a couple of seconds so performing properly but the light remains on.
What are the error codes for the OBD code?
Has error codes p0562, p2308, p2302, p0306, and p0300. It smokes alot from exhaust pipe, and when it’s running if you remove the oil filler cap it has a really strong suction. What could be
Can a canister of R134a indicate no fault?
Also worth noting pressure does not indicate refrigerant quantity. A canister of R134a will have the same pressure inside it with 13.5 kg of gas/liquid in it as one that has 5 kgs in it at the same temperature.. G65 showed as fault and kept tripping a fuse, this was changed now no fault, air con worked for a while but not now? intermitent? dead?
The wires in question run from a plug attached to something on the left had side of the engine (as you look at it) down by the alternator up to the wiring loom which runs across the rocker cover, not sure quite where they go to. Click to expand… Me too, i have same problem, EDC light always on.
What causes a Mercedes Benz to have a p1470 fault?
Have found reliable source of getting fault codes and discover fairly common P1470 fault. Reading all the posts I think it must be either the vacuum system or catalytic converter. I have checked vacuum hoses and all seem to hold vacuum with my tongue blocking the end.
What is the fault code for a Volvo truck?
Reset ABS Faults, Body Controller Faults and more. 1 Volvo Link System Faults (MID 142) Fault Code Description FMI MID 142 PID 155 Input 1-4. 2 Vehicle ECU Faults (MID 144) 3 Climate Control Faults (MID 146) 4 Light Control Module Faults (MID 216) 5 Gear Selector Module Faults (MID 223)
Similar problem with the bas brake assist, had it diagnosed, replaced g force sensor and brake sensor, as that what fault codes came up, reset it, but light is back on!! Spent allot of money on original parts, and it is still the same, could it be the ECU it’s self?
Where can I find the Mercedes Fault code?
Any of the scanners listed above can read and clear the Check Engine / Service Engine Fault Codes. The codes above are retrieved by plugging a diagnostic scanner into the OBD-II port located under the dash, and scanning for fault codes. Location of OBD II port used to retrieve Mercedes-Benz fault codes.
What is the DTC code on a check engine light?
Diagnostic trouble codes (DTC) are automotive computer codes stored by the on-board computer diagnostic system (OBD) in your vehicle. There are literally hundreds of different codes a Check Engine Light can represent.
Any of the scanners listed above can read and clear the Check Engine / Service Engine Fault Codes. The codes above are retrieved by plugging a diagnostic scanner into the OBD-II port located under the dash, and scanning for fault codes. Location of OBD II port used to retrieve Mercedes-Benz fault codes.
On start up I had two warning lights, glowplug light on (always) and the EDC light on (always). The glow plugs have current for the heat up process and then there is no currnet to them after a couple of seconds so performing properly but the light remains on.
What kind of fault is on Vito 111cdi?
Travelling at speed on the motorway, van went into ‘limp’ mode and engine fault light came on. An investment in the excellent ELM 327 bluetoth code reader and equally good free ‘Torque’ app showed the fault to be P0404 – Exhaust Gas Recirculation Circuit Range/Performance.
Can you read the fault code on a Mercedes Benz?
Can read fault codes from multiple systems such as transmission, engine, ETS, airbag and more. Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS
Can a launch creader VIII read a fault code?
1. Launch Creader VIII Can read fault codes from multiple systems such as transmission, engine, ETS, airbag and more. Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3.
What are the symptoms of a diesel injector failure?
It is unusual for a simple mechanical injector to fail completely and suddenly. The symptoms include smoking from the engine exhaust – usually grey smoke indicating unburnt fuel – this will smell strongly and be rather unpleasant to inhale, making the eyes smart, often more noticeable when the engine is cold.
What is the error code for a bad fuel injector?
For example, a fault with an injector in cylinder one would give a code of P0201. You may also see other error codes such as P0101, P0300, P0299. Visually inspect the engine bay – If you open up the hood and there is a strong smell of fuel then a leaky injector could be the culprit.
What is the diagnostic code for fuel injector problems?
The injector can face problems due to a contamination of the inlet filter on the injector. It is also possible for this problem to arise because of a dirty or clogged fuel filter or a defective fuel pump. P0253 is widely known as the diagnostic trouble code for “Injection Pump Fuel Metering Control A Low (Cam/Rotor/Injector.”
What causes a fuel injector to fail mechanically?
A fuel injector will usually only fail in one of two ways. It will either become clogged internally, or will fail mechanically . Here’s a list of the most common reasons why a fuel injector fails: 1. Dirty/Clogged Injectors – What causes a fuel injector to become blocked? Over time the nozzle of the injector can become dirty, and partially blocked.
Is the Mercedes Benz Vito radiator losing water?
Morning all My vito has been losing a little bit of water ever since i have owned her (bout 3 months) it has only been a tiny amount so nothing to worry about until yesterday. As you know the sunny uk is a foot under snow Went to pick me lad up from his nans yesterday and had a water problem.
When did the Mercedes-Benz Vito V class come out?
It is available as a standard panel van for cargo (called Vito), or with passenger accommodations substituted for part or all of the load area (called V-Class or Viano ). The V-Class/Viano is a large MPV. The first generation went on sale in 1996. The second generation was introduced in 2004, and the vehicle received the new Viano name.
Who are the repeat buyers of my Vito?
My Vito is atypical of the reputation that MB Vans have in this country – and they’re regarded as now intruding right into the japanese/korean small van market. They have the highest repeat customer base and dominate fleet buyers such as Police, Ambulances etc…
When did the Mercedes Benz Vito become Euro 3 compliant?
The vehicles have a new 6-speed manual gearbox gear ratios designed for fuel economy. The second generation Vitos are Euro 3 compliant (additionally Euro 4 compliant as of November 2006) and exempt from the Low Emission Zone in London, which requires commercial vehicles (vans) to reach at least Euro 3 standard from October 2010.
Is the Mercedes Benz Vito 110 CDI compact?
For stopping power, the Vito 110 CDI Compact braking system includes Vented Discs at the front and Discs at the rear. The Vito model is a Van car manufactured by Mercedes Benz, with 4 doors and 2-3 seats, sold new from year 2019.
Which is the least efficient Mercedes Vito van?
Surprisingly, the least efficient model is the 1.7-litre 110 CDI Progressive L3 front-wheel drive manual, at 36.7mpg. However, there’s only a difference of around 3mpg between the Vito’s best and worst performers.
What kind of gearbox does the Mercedes Vito have?
Progressive trim is the only one offered with a manual gearbox, and these versions are front-wheel drive with the 110CDI or 114CDI-badged 1.7-litre diesel, only in L1 and L2 body lengths. All other versions of the Vito diesel feature the larger 2.0-litre motor, are rear-wheel drive and feature Mercedes’ latest 9G-Tronic auto gearbox.
When did the Mercedes Vito van come out?
The arrival of the current van in 2014 introduced front- or rear-wheel-drive transmission layouts, a choice of two wheelbases and three body lengths.