Why does my Mercedes Benz make a clicking sound?

Why does my Mercedes Benz make a clicking sound?

The clicking sound and the rest of the symptoms may be attributed to a broken stepper motor lever or the footwell damper linkage. This is a common problem in MB C230, C240, C320, CLK320, CLK350, CLK500 but this problem can affect other Mercedes-Benz models such as E, S, CLS, GL, ML Class.

Why does my Mercedes Benz W204 suspension make noise?

If the bushing has torn or ruptured, it is possible for the surrounding area to be wet with fluid. This is a clear sign of a bushing failure. Another area where owners have experienced suspension noise has been in the strut assemblies and springs. Surprisingly, these have been replaced quite regularly on the w204 models.

What kind of problems does a Mercedes C230 have?

The contacts owns a 2006 Mercedes C230. The contact stated while driving 20 mph, the vehicle started to shake violently. Also, the contact mentioned that smoke started to emit from the engine compartment and from underneath the vehicle. The vehicle was taken to the dealer.

Why does my steering make a knocking noise?

Steering had a little play and makes a slight clunk or knock in either direction. Thanx. Have you inspected the steering coupler? It is at the bottom end of the steering column shaft, and connects the shaft to the gearbox. That’s the most likely culprit.

Why does my Mercedes C class make a clicking noise when turning?

Typical ball joints on 2-wheel drive C-Class models. Individuals with 4MATIC all wheel drive models may experience a clicking noise that may seem to be coming from the front suspension when turning; however, it is likely a worn front CV joint.

If the bushing has torn or ruptured, it is possible for the surrounding area to be wet with fluid. This is a clear sign of a bushing failure. Another area where owners have experienced suspension noise has been in the strut assemblies and springs. Surprisingly, these have been replaced quite regularly on the w204 models.

Why is my front suspension making a clunking noise?

Front end link with missing fastener. The front suspension components utilize ball joints at the control arms and tie rod ends. The extensive range of motion of these spherical links are quite robust and meant to last; however, contamination of the joint can lead to premature failure often accompanied by a clunking or knocking noise.

Why does my Mercedes C class suspension Squeak?

As previously mentioned with sway bar bushings, the rubber rear sway bar end link bushings can age and squeak. Lubricant can temporarily resolve the squealing, although it is recommended new end links be installed. Figure 6. Front end link with missing fastener.

What to do if your Mercedes Benz is clunking?

Recently had a free MB Tech Session at the local Benz dealership where they go over several points with you. Technician diagnosed a leaking drivers side motor mount and lower control arm bushings that had a very, very slight amount of play. He said those bushings didnt need replacement now, but maybe next year or 15k miles left on them. (roughly).

What to do if you have a Mercedes transmission problem?

An advanced diagnostic scanner such as the iCarsoft or the Launch Creader listed here are a must for do-it-yourself Mercedes-Benz repair. They are affordable and can access most of the systems on your Mercedes-Benz including Airbag, EPS, ETS, Transmission, Engine, front and rear SAM, SRS, brakes and a lot more. 3.

What to do when your Mercedes goes into limp mode?

You may also get a check engine light if your transmission goes into limp mode. When a Mercedes-Benz goes into limp mode, it only operates in second gear and reverse only. When you put it in gear, you may also feel a bang as transmission engages. The first thing you should try is to check the transmission fluid level.

Why does my Mercedes Benz make a clicking noise?

It requires electrical power to crank the engine. The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars.

Why does my Mercedes Benz not turn on?

A problem that Mercedes-Benz owners may face is the key no longer turns in the ignition. This issue is often caused either by a defective key, bad shifter module, a failed Electronic Ignition Switch (EIS) also known as the EIS-EZS or a bad steering lock module (ESL).

What to do if your Mercedes ignition switch is not working?

If you have a spare key try to see if you are experiencing the same symptoms with the other key. If the other key works, keep using it for a couple of weeks to verify that the issue is really the key and not the EIS. Try scanning your Mercedes-Benz for fault codes. Ideally using a Start Diagnostic Scanner.

What do I need to troubleshoot my Mercedes Benz?

Troubleshooting fuel related problems is not very difficult and you can check the fuel pressure yourself. Checking the fuel pressure is very simple. For this test, you will need a fuel pressure gauge. What you need is a fuel pressure gauge with Schrader valve adapter.

Why does my car make a thumping noise when I drive?

It’s not a ticking or hard knocking noise. Also, the noise is variable depending on the speed AND the duration of noise is also speed dependent (going slow, the thump is drawn out. Going faster, the thump duration is shorter.) Here’s what I have done so far but the noise is still there. Rotated both front tires to rear

Where does the thumping sound come from in my Murano?

I have started hearing faint thumping noise in my Murano, coming from the front most likely. It sounds as if I have a bold spot on a tire and is very faint. I can also feel it faintly through the steering wheel. It’s not a ticking or hard knocking noise.

Why does my Mercedes Benz front end keep popping?

Im really thinking that the LCABs are the culprit. The factory tech visually spotted the cracks in them, but when he pried against them with a long prybar, there wasnt (in his opinion) enough play to warrant immediate replacement. A second opinion at a local German independent said the same thing.

It’s not a ticking or hard knocking noise. Also, the noise is variable depending on the speed AND the duration of noise is also speed dependent (going slow, the thump is drawn out. Going faster, the thump duration is shorter.) Here’s what I have done so far but the noise is still there. Rotated both front tires to rear

I have started hearing faint thumping noise in my Murano, coming from the front most likely. It sounds as if I have a bold spot on a tire and is very faint. I can also feel it faintly through the steering wheel. It’s not a ticking or hard knocking noise.

Is there a ticking noise in the steering wheel?

I can also feel it faintly through the steering wheel. It’s not a ticking or hard knocking noise. Also, the noise is variable depending on the speed AND the duration of noise is also speed dependent (going slow, the thump is drawn out. Going faster, the thump duration is shorter.)

Why does my car make a chirping sound when the engine is running?

A serpentine belt is used to supply engine power to the water pump, alternator, power steering pump and air conditioner compressor. When this belt starts to wear it becomes glazed and will loose its ability to grip the pulleys which can produce a chirping sound while the engine is running.

Why does my Mercedes make a squeaking noise when I turn the wheel?

Problem. When you turn the steering wheel on your Mercedes-Benz you may hear a loud squeaking or weird whining noise. The noise is a common problem, with Mercedes Benz E-Class, S-Class, C-Class and ML-Class and it is most noticeable when you first start up the car. Typically the engine is cold. Can often be heard when you are a stop light.

When do you turn the steering wheel do you hear a whining noise?

When you turn the steering wheel on your Mercedes-Benz you may hear a loud squeaking or weird whining noise. The noise is a common problem, with Mercedes Benz E-Class, S-Class, C-Class and ML-Class and it is most noticeable when you first start up the car. Typically the engine is cold. Can often be heard when you are a stop light.

Where does the beeping come from on my Mercedes?

I’m getting a random beeping noise coming from the dash somewhere. It is totally random, sometimes a longer beep when I stop. It seems to be coming from the dash somewhere, but I am unable to trace it down exactely. It is not the radio, I have an aftermarket Pioneer deck that I completely took out and the beeping did not stop.

Why does my car make a beeping noise when I stop?

I’m getting a random beeping noise coming from the dash somewhere. It is totally random, sometimes a longer beep when I stop. It seems to be coming from the dash somewhere, but I am unable to trace it down exactely.

Why does my Mercedes Benz whistle stop working?

So I canceled my order on part 202-800-18-75. After cycling the re-circulating button a few times and sucking on the tube by mouth trying to figure out the problem, it magically started working properly again and the whistle stopped. So I put it all back together and have not had a problem yet but it has only been a couple of days.

What to do when your car beeps while driving?

The beeping is driving me NUTS!!!!!!!!!!!! Pull the park brake up a little when driving see if it is the same beep. Yours sounds like an issue I had awhile back.

Why does my stereo make a loud popping noise?

In the beginning my stereo would make a loud pop and then not emit any sound. The display would work, and I could change the stations, inputs, and volume, but no noise would come out of the speakers. I would simply turn the car off and back on and the problem would be resolved.

Why does my car stereo pop when I start the car?

Since, this gremlin has transformed into a creature off a “Predator” movie. Now when I start my car, the music may play for a couple seconds and then the loud popping takes over. Whether the volume is on “1” or “10” the noise is just as loud and startling. I would simply turn off the power to the stereo, but this did not seem to alleviate anything.

What to do if your Mercedes Benz Radio is not working?

For you to do that, you will need to remove the fuses for the CD Changer, COMAND/ NAV / DVD Player / Radio, Audio Gateway AGW, and the Voice Unit if it is equipped with one, for at least 10 minutes. Doing a soft reset for these systems will force the head unit to rest. This normally restores the systems to working order.

In the beginning my stereo would make a loud pop and then not emit any sound. The display would work, and I could change the stations, inputs, and volume, but no noise would come out of the speakers. I would simply turn the car off and back on and the problem would be resolved.

Since, this gremlin has transformed into a creature off a “Predator” movie. Now when I start my car, the music may play for a couple seconds and then the loud popping takes over. Whether the volume is on “1” or “10” the noise is just as loud and startling. I would simply turn off the power to the stereo, but this did not seem to alleviate anything.

What causes a Mercedes Benz to have no sound?

Some common problems with the Mercedes-Benz COMAND system include issues such as: 1 Head Unit / Radio stuck on Mercedes-Benz logo 2 Turns on and then off 3 Shuts off randomly 4 COMMAND will freeze 5 Radio powers on but there is no sound 6 Audio Gateway (AGW) drains the car battery 7 Radio panel doesn’t turn on. (Hint: Check fuses.) More

Why is the radio not working on my Mercedes Benz?

Is the radio on your Mercedes-Benz not working? Some common problems with the Mercedes-Benz COMAND system include issues such as: Radio panel doesn’t turn on. (Hint: Check fuses.) The fist thing you should try is to do a soft reset of the COMAND unit.

What makes a clicking noise when the AC is turned on?

Brief, loud clicking noise from dashboard area when AC is… Q: Brief, loud clicking noise from dashboard area when AC is turned on. This started happening about 2 weeks ago. When I start up my car or whenever I turn the AC on I hear 3 or 4 loud clicks coming from what seems to be under the dashboard.

How to fix ticking sound in the dashboard?

How To Fix Mercedes-Benz Ticking Sound in the Dashboard Problem 1 Symptoms: Noise Under the Dash. 2 Problem: The clicking sound and the rest of the symptoms may be attributed to a broken stepper motor lever or the footwell damper linkage. 3 Solution: If it is indeed the linkage that’s broken, you have to replace it. …

How much does it cost to repair a Mercedes dashboard?

However, the process of replacing it takes hours, especially for beginners. If you would like to take it in, instead, repair centers charge up to $500 for their service due to the time required to disassemble and reassemble dashboard components. The stepper motors could also be defective and get stuck in open or closed position.

The clicking sound and the rest of the symptoms may be attributed to a broken stepper motor lever or the footwell damper linkage. This is a common problem in MB C230, C240, C320, CLK320, CLK350, CLK500 but this problem can affect other Mercedes-Benz models such as E, S, CLS, GL, ML Class.

How To Fix Mercedes-Benz Ticking Sound in the Dashboard Problem 1 Symptoms: Noise Under the Dash. 2 Problem: The clicking sound and the rest of the symptoms may be attributed to a broken stepper motor lever or the footwell damper linkage. 3 Solution: If it is indeed the linkage that’s broken, you have to replace it.

What makes a tapping noise in the dash?

My 2002 C230K with 71K on it has recently developed a loud tapping noise which emanates from the dash behind the radio/climate control. At the same time the ventilation system will no longer blow air through the dash vents. The defroster and foot vents still work.

However, the process of replacing it takes hours, especially for beginners. If you would like to take it in, instead, repair centers charge up to $500 for their service due to the time required to disassemble and reassemble dashboard components. The stepper motors could also be defective and get stuck in open or closed position.

What does clicking from pass side low dash mean?

Take some pics if you can. Always nice to have as much info as possible on a repair. It will help those who follow in your footsteps.:biggrin:

Is it making a clicking noise behind the dash?

An expert that got 20 achievements. An expert that got 10 achievements. An expert that got 5 achievements. Re: It is making a clicking noise behind the dash when I…

What causes a Mercedes convertible top to leak?

The majority of Mercedes convertible problems are caused by a bad relay, weak lift cylinder or lift cylinder leaking by the o-ring. If you find out that the convertible top reservoir is low in fluid that means that you have a leak most likely at one of the convertible lift cylinders.

Are there swaybar links on the front of a Mercedes Benz?

Just left the parts counter at the Benz dealership in Maryland. two different parts guys were checking the computer. they said the 2002 CLK55 AMG Convertible has no endlinks/swaybar links up front. Is that accurate?? I had a worn out steering damper/stabilizer that clunked when wheels turned past a certain degree, have you checked that out?

Why is my Mercedes Benz clunking in traffic?

Went for a drive into the city (Georgetown section of DC) in a lot of traffic the other day, and the clunking/popiing was definitely more pronounced in the heat. Slow turning into a parking space? A pop or clunk would happen.

Why does my Mercedes supercharger make a rattling noise?

The supercharger has been making rattling and grinding noises for a while now. It seems to function well but it just makes these annoying noises when it is engaged. The pulley spins freely and smoothly when not engaged and when the car is idling.

Why is my Mercedes C class engine not working?

One Mercedes specialist told be that my cars engine is a gonner and the timing chain and gears were also damaged. Another one told us that our ECU was faulty and then suddenly there was no pressure on the one valve and so the so-called list of difference diagnosis started.

Why does my Mercedes C class run rough off-idle?

21 people found this helpful. Hmmm, so what you’re saying is it idles ruff but passed that part of the test and runs smooth off-idle but fails that part because it’s running too rich ( too much fuel). If you had a vacuum leak at the throttle body you’ll be running lean not rich as you are now.

Why does my Mercedes C230 make a clunking noise?

While there are a variety of reasons your Mercedes-Benz C230 is rattling, the most common 3 are the ball joints, struts or strut mount, or a problem with the sway bar links. A “clunk” or “knock” when turning or going over bumps can indicate a problem with a ball joint.

The supercharger has been making rattling and grinding noises for a while now. It seems to function well but it just makes these annoying noises when it is engaged. The pulley spins freely and smoothly when not engaged and when the car is idling.

Why do I hear a ticking sound in my Mercedes Benz?

When you start your Mercedes-Benz, or even just turning the AC on, you hear a clicking sound (at times a shhh sound) from the dashboard. The sound lasts for about 20 seconds then goes away after approximately 5 minutes. Later on, however, the ticking returns and repeats its cycle.

Why does my Chevy Equinox make a rattling noise?

A “clunk” or “knock” when turning or going over bumps can indicate a problem with a ball joint. The sensation is often felt in the floorboard. A repair technician may notice if…

What causes a loud clicking noise during acceleration?

Noise: Banging or heavy clicking every two to three feet during acceleration and deceleration Cause: Damaged or broken pinion gear tooth or teeth Noise: Banging or heavy clicking every two to three feet during acceleration or deceleration, but not both

What kind of noise does a lifter make?

If the noise can not be isolated to a specific bank, then in the majority of situations this would not be a lifter related noise. VARIABLE CAM TIMING The 4.6L 3V and 5.4L 3V variable cam timing (VCT) feature may emit a light knock in normal operation and is audible only at idle speed, with a hot engine (gear selector in parktneutral).

What causes a clunking noise on the driveline?

Cause: Bad wheel bearings Noise: Driveline squeaking or grinding at any speed Cause:Worn or damaged U-joints Noise: Clunking when depressing the throttle pedal (takeoff) Cause:Worn U-joints; worn spider gears; worn axle splines; excessive gear backlash; loose yoke splines; worn slip yoke splines Noise:Clunk immediately after taking off from a stop

How to troubleshoot your Mercedes Benz air conditioner?

Identify the location of your compressor. Look at the pullyer and you should be able to see if it spining or not. The engine running turn the A/C on max cool, set fans high, and make sure that the clutch is engaging on the compressor. The pulley spins any time the engine is running. The center part of the A/C pulley only engages when the A/C is on.

What is the recirculated air button on a Mercedes?

This is as far as the cylinder will go without cranking the engine. Press and hold the defrost and recirculated air buttons simultaneously. The defrost button has three lines going through it, while the recirculated air button has a picture of a car with a curved line through it.

Identify the location of your compressor. Look at the pullyer and you should be able to see if it spining or not. The engine running turn the A/C on max cool, set fans high, and make sure that the clutch is engaging on the compressor. The pulley spins any time the engine is running. The center part of the A/C pulley only engages when the A/C is on.

This is as far as the cylinder will go without cranking the engine. Press and hold the defrost and recirculated air buttons simultaneously. The defrost button has three lines going through it, while the recirculated air button has a picture of a car with a curved line through it.

Why does my Mercedes car flash service lights?

Your Mercedes vehicle will flash a host of service lights to inform you when something might be damaged inside the car. If the air conditioner unit is not running normally or is only blowing out warm air, it may be a temporary fault.

Are there any problems with the Mercedes C300?

Finally, the dealership paid for a new battery after the car failed to start for the last time. On average the problem occurred at 75,800 miles and typically cost owners $1,350. The No. 1 problem for the Mercedes-Benz C300 is for the 2011 model year. Only one owner submitted a complaint.

What’s the price of a Mercedes Benz C300?

Advanced safety features that come standard on this Mercedes-Benz are forward-collision warning, automatic emergency braking, pedestrian detection, and blind-spot warning. Pricing for the 2020 Mercedes-Benz C300 starts at $41,400. The Mercedes-Benz C300 is a stylish, sporty competitor in the luxury small car segment.

What kind of car is a 2008 Mercedes Benz C 300?

Used 2008 Mercedes-Benz C 350 Sport $4,999 Private Seller Used 2008 Mercedes-Benz C 300 Sport Sedan $6,200 Reduced BLOK Charity Auto Clearance Used 2008 Mercedes-Benz C 300 Sport Sedan $9,800 Reduced Carex Used 2008 Mercedes-Benz C 350 Sport $11,995 MGM Auto Sales Used 2008 Mercedes-Benz C 300 Sedan $6,995 Selected Motors Used 2008

How much does a Mercedes C 300 cost?

Mercedes-Benz C 300 4MATIC Sedan $8,886 Volkswagen of Downtown LA Used 2008 Mercedes-Benz C 300 Sedan $9,995 Private Seller Used 2008 Mercedes-Benz C 300 Luxury Sedan $11,999 Miramar Sport Cars Used 2008 Mercedes-Benz C 300 Luxury Sedan $12,999 Siry Auto Group 12 Mercedes-Benz C-Class vehicles for sale near you. See Cars for Sale Advertisement

Where can I find a 2008 Mercedes C Class C?

Get KBB Fair Purchase Price, MSRP, and dealer invoice price for the 2008 Mercedes-Benz C-Class C 300 Sport Sedan 4D. View local inventory and get a quote from a dealer in your area. Home Car Values Price New/Used My Car’s Value Instant Cash Offer Cars for Sale Cars for Sale Sell Your Car Free Dealer Price Quote Vehicle History Report

When was the last serviced Mercedes-Benz C Class C 300?

Last serviced at 76,734 miles in Lawrenceville, NJ on 02/15/21 • Vehicle serviced • Antifreeze/coolant checked • Thermostat replaced • Antifreeze/coolant flushed/changed • Cooling system checked. Mileage: 76,920 miles Body Type: Sedan Color: Gray Engine: 6 Cyl 3.0 L

Recently had a free MB Tech Session at the local Benz dealership where they go over several points with you. Technician diagnosed a leaking drivers side motor mount and lower control arm bushings that had a very, very slight amount of play. He said those bushings didnt need replacement now, but maybe next year or 15k miles left on them. (roughly).

Why does my Mercedes Benz have a vibration?

If you are feeling a vibration or shimmy from your Mercedes Benz front-end, there are a few simple inspections that you can do.

What are the signs of a Mercedes Benz suspension problem?

Signs of failure are common and are often accompanied with a “creaking” noise from the suspension. Other components such as wheel bearings, ball joints and sway bar links should be inspected at the same time.

What makes a Mercedes Benz front end Shimmy?

These forces can be extreme and cause the rubber bushings to fatigue and crack causing a front-end vibration or shimmy. Signs of failure are common and are often accompanied with a “creaking” noise from the suspension. Other components such as wheel bearings, ball joints and sway bar links should be inspected at the same time.

How can I tell if my Mercedes Benz sway bar is working?

There should be no movement vertically or laterally. Sway Bar Links – Visually inspect the links connecting the sway bar to the control arms. These may be rubber or may have a ball joint style connection. If your Mercedes Benz has rubber bushings, look for cracking or failure of the bushings.

How much does a Mercedes Benz SL 55 AMG cost?

Prices for Mercedes-Benz SL Sl-55-amg s currently range from $12,549 to $36,500, with vehicle mileage ranging from 33,151 to 112,000. Find used Mercedes-Benz SL Sl-55-amg s near you by entering your zip code and seeing the best matches in your area.

What happens when a Mercedes Benz goes into limp mode?

When a Mercedes-Benz goes into limp mode, it only operates in second gear and reverse only. When you put it in gear, you may also feel a bang as transmission engages. The first thing you should try is to check the transmission fluid level. The transmission has a dipstick tube but with no dipstick in it.

Why does my Mercedes make a clunking noise when I turn the steering wheel?

Today I jacked the front end of the car up and turned the steering wheel from side to side. No noise at all. No play in steering wheel. Steering seems nice and tight. The steering box bolts are also torqued to spec. Based on this info…what could it be? I can also feel the clunk right under my feet as Im driving.

How is the audio system in a Mercedes Benz connected?

All the audio related systems in the car are connected via the fiber optic cable in series, forming a ring or a loop. The signal will travel through all the different components and return back to the same component if required. Components that are part of the fiber optic ring are:

How to do soft reset on Mercedes Benz no sound?

The fist thing you should try is to do a soft reset of the COMAND unit. To do a reset you will need to remove the fuses for at least 10 min for these systems: By removing the fuses for these systems, you will be forcing the command unit to perform a rest.

Is the radio on your Mercedes-Benz not working? Some common problems with the Mercedes-Benz COMAND system include issues such as: Radio panel doesn’t turn on. (Hint: Check fuses.) The fist thing you should try is to do a soft reset of the COMAND unit.

How much does it cost to repair a Mercedes dashboard linkage?

The linkage itself is relatively cheap. However, the process of replacing it takes hours, especially for beginners. If you would like to take it in, instead, repair centers charge up to $500 for their service due to the time required to disassemble and reassemble dashboard components.

Where does the clicking noise come from on my car?

Intermittent Clicking Noise Coming from behind center of dash when starting engine or as Key is pulled out of ignition. Clicking noise that seems to be coming from the center of the dashboard, upon start up. After a few minutes the noise disappears. My Service Advisor mentioned that it is coming from the AC/Heater system, flapper.

How much does a Mercedes Benz clk500 cost?

The average cost for a Mercedes-Benz CLK500 General Diagnosis is between $143 -$180. Learn More same problem i have 2004 clk 500 and the noise behind the dash continues even with car completely shut off and my a/c blows cold but doesnt blow like it should like as if it was blocked.???

Are there any problems with the Mercedes ML 350?

From the balance shaft issue to differential problems they are just trouble. There are also problems with water leaks through the right rear tail light seal. You would be fine with a 2009-2011 ML 350 or 550. The V8 is pretty reliable, but still pricey for those model years.

Why does my HP printer make a clicking noise?

12-31-2019 09:25 AM Our printer is making a very loud clicking noise when we attempt to print. The paper was also jamming. I changed the rollers in the back of the printer. Now I just have the clicking noise. The printer is 1 1/2 years old, the warranty ran out in May. I tried using another printer tray from an identical printer. That did not help.

How do I Turn Off the mouse clicking sound?

When you see an option for Hardware and Sound, click on it. Within the Hardware and Sound dialog, there is an option to Change systems settings and sounds. You choose Change system sounds. From the Change Sounds dialog, scroll down to Start Navigation, and click on it.

Why is my sound not working on my computer?

Some sound drivers use software “enhancements” in an attempt to improve your sound quality. If these aren’t working properly—or if your CPU is being taxed too heavily—these could result in sound problems. To disable sound enhancements, use the same Properties window.

Why does an overhead cam engine make a clicking noise?

In an overhead cam engine, the camshaft lobes themselves depresses the valve while in single cam engines, the cam actuates push rods that open the valves by moving a lever called the rocker arm. Since your valves move very quickly and only move a short distance, the distance from the cam or pushrod to the valve needs to be very precise.

Why does my pushrod engine make a ticking noise?

If you have a pushrod style engine with solid lifters, may want to make sure the lifters are clean as there can be oil deposits built up on them which can also cause noise. This is the least expensive fix as you can typically change the motor oil in your car and the lifter tick will go away. Lifter Tick or Rod Knock?

Why does my car make a clicking noise when I idle?

Your fuel injectors are small electrical valves that open and close very quickly allowing a certain amount of fuel to be injected with the air your engine is drawing in. Some vehicles, like many Subarus, have injectors that you can actually hear opening and closing at idle. It should sound like a sharp pencil tapping on a desk and be very rhythmic.

https://www.youtube.com/watch?v=5B11viw7ih0

When did the Mercedes C320 CDI long term test?

Long-term test report – 7 October 2008. So my Mercedes C-class has gone – and I will miss it like few other long-term cars. The C320 CDI really got under my skin.

How much torque does a Mercedes C320 CDI have?

Throw in one of the finest current turbodiesel powerplants and you have an unfeasibly brisk and refined package that can rack up 600 very fast miles between tanks. It’s the torque that makes the C320 CDI such a devastatingly quick point-to-pointer – there’s a mighty 376lb ft of turbo-enhanced torque that arrives at a low 1600rpm.

What are the headlamps on a Mercedes C320?

The C320’s headlamps are some of the best I’ve ever used. Its optional Intelligent Light System uses active bi-xenons that are 50 percent more powerful than conventional headlamps. They also automatically adapt to driving conditions, according to a number of speed-related parameters.

What should I do about my Mercedes 320 CDI?

Just do it, repair and maintain yourself (you’ll need a Star C3/Xentry tool [needed for something as simple as an engine air filter change]), and allow for new glow plugs and glow plug controller. Very nice to driver, and you are right, that kind of low down torque makes for effortless driving.

How reliable are the 320 CDI engine / transmission, particularly the 2008?

How reliable are actually the 320 CDI engine/transmissions, particularly the 2008? I read a lot about oil leaks – is this a serious problem? I had a 300D for 13 years and I am thinking of buying a diesel again – the torque of the 320 CDI seems to be fantastic, providing power at low rpm. But what about this leaks?

What was the repair on my 2008 CDI?

The ’08 recently had the intake flap repair which I expanded to include the oil cooler seals. Somewhat pricey repair @ $3,500ish at the dealer. Several years ago it also needed a starter @ about $700. Another job performed at the dealer which I understand required removal of the right motor mount.

Is the C320 and C240 the same engine?

The C240 and C320 use basically the same M112 engine (the 240 is de-stroked for less HP and displacement), so yes, that would be the same belt. Please help! Can anyone tell me if this would be the same belt used to bypass the AC pulley on a R-Class 350 6 cylinder?

Is that engine the same of the 04 CLK320?

I would like run the engine of my 2004 (W209) CLK320 without the A/C compressor. This is to confirm whether the whining noise is from the A/C compressor. A shorter serpetine belt would do it. I read the post above suggesting “Duralast 910K6” or “6PK2310” for a 04 C340. Is that engine the same of the 04 CLK320?

Why does my Mercedes Benz C class Rattle?

It’s not uncommon to hear some squeaks and rattles in an older car. However, some Mercedes-Benz C-Class owners are reporting rattling in much newer vehicles. This guide will give you an idea of why your car’s interior is rattling. This article applies to the Mercedes-Benz C-Class (2007-2014).

Why does my CLK W209 make a buzzing noise?

These instruction should also help the CLK W209 and CLS owners. If the buzzing noise comes from the rear sub-woofer installed right under the rear glass, you may want to unplug the wire to that sub-woofer until you have a chance to replace it.

Why does my car speaker keep making noise?

If one of the speakers in your car has “blown” it’s time to replace it. Do you have serious sound distortion when you play any music? Older speakers do wear out and then start to crackle, even if you don’t blast your music. When a speaker blows it makes noise that you can’t miss and the sounds that it emits is very distorted.

Why does my Mercedes Benz W203 make a rattling noise?

My 2001 W203 (with 79,000 miles) has a knocking/rattling noise coming from the front suspension. It occurs at any speed. Even moving very slowly, any undulation of the pavement causes a knocking/rattle. I’ve read that it may be the sway bar end links.

Why does my C class car make a rattle noise?

Thanks for your thoughts. check your guide arm bushings, on the c class they are known to fail often. they cause a clunking noise in the front end going over bumps. will also cause noise on any road. My car just started making a rattle/klunk as you describe and I’ve been trying to identify the source.

Why does my CLK W211 speaker make noise?

Older speakers do wear out and then start to crackle, even if you don’t blast your music. When a speaker blows it makes noise that you can’t miss and the sounds that it emits is very distorted. The purpose of this article is to show you how to replace a the speaker on a E Class W211. These instruction should also help the CLK W209 and CLS owners.

If one of the speakers in your car has “blown” it’s time to replace it. Do you have serious sound distortion when you play any music? Older speakers do wear out and then start to crackle, even if you don’t blast your music. When a speaker blows it makes noise that you can’t miss and the sounds that it emits is very distorted.

Why is my fan making noise when it rotates?

Sometimes the plate the blades mount on can come loose. You may need to remove all fan blades, level the mounting plate (usually one set screw tightens against a rotating shaft). Turn the fan on w/o blades to see if the plate wobbles and then replace blades. Was this answer helpful? Have you checked the alignment, It could be unlevel.

What should I do if my car fan is making a loud noise?

Clean back bushing and lubricate with household oil (not WD 40) Lubricate outside of motor. Drop oil on front bushing work back and forth. If still binds then remove T pin clean and lubricate front bushing. Re assemble and should work fine.

Why does my car fan make a ticking noise when it spins?

This makes something rub when it gets spinning fast. You may also notice a slight wobble when the fan is running. I know this can happen. This happened to me. It only made noise on high speed. After cleaning the blades, the wobble and ticking noise stopped.

What should I do about my hp ml350p fan noise?

Install all firmware updates and driveers, then reboot your system, enter the BIOS setup. Go to the thermal configuration page in the advanced power options, make sure the server is set to “Optimal Cooling”. No more ramping noise, no more loud fans!

Why is my Ceiling Fan making a clicking noise?

A ceiling fan making clicking noise may be caused by blades that aren’t firmly attached to the fan assembly. This problem is easy to correct and generally only requires a set of screwdrivers. Here’s how you tighten fan blade screws:

Is the ml350p still running at 31%?

I have an ML350P that has been in for a year and four months now and it has been fine. In the past couple of weeks the fans have started running a bit harder they normally run at around 10% or just under, at the moment they are running at 31%.

What kind of noise does a bad wheel bearing make?

As you drive faster the bad bearing sounds lower but you will still hear the noise at low speed as well. The noise generated from a bad wheel bearing really depends on the nature of the wear. Some common sounds you will hear from a bad wheel bearing are: It is difficult to confirm the bad wheel bearing by simply rotating the tire.

When does the ticking sound in the dashboard go away?

The sound lasts for about 20 seconds then goes away after approximately 5 minutes. Later on, however, the ticking returns and repeats its cycle. Other times, you may feel that the fan speed is not normal. It speeds up and slows down all of a sudden. You may also notice that there is no air blowing on the floor.

As you drive faster the bad bearing sounds lower but you will still hear the noise at low speed as well. The noise generated from a bad wheel bearing really depends on the nature of the wear. Some common sounds you will hear from a bad wheel bearing are: It is difficult to confirm the bad wheel bearing by simply rotating the tire.

The sound lasts for about 20 seconds then goes away after approximately 5 minutes. Later on, however, the ticking returns and repeats its cycle. Other times, you may feel that the fan speed is not normal. It speeds up and slows down all of a sudden. You may also notice that there is no air blowing on the floor.

Why does my engine make a clunking noise when I Turn on the engine?

Rod knock comes from a bad bearing in your connecting rod. As the bearing wears out it will allow movement and that play will sound like tapping or clunking depending on how bad it is. If you’ve got rod knock the sound will change with engine RPM and will not change with engine temperature or load.

What are the problems with a Mercedes Benz?

Top 5 Mercedes-Benz no start problems 1 Engine Click, No Start 2 Engine Dies Right After It Starts 3 Car turns over, but it won’t start 4 The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery 5 Key will not turn the ignition More

Why is the battery on my Mercedes Benz not working?

Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars. How old is the battery on your Mercedes-Benz?

Why does my K20 engine make a tapping sound?

So although the tapping sound coming from the engine’s head may in fact be a problem with the tappets specifically, it could also be a problem with the camshaft, rocker arms, valves or even just a lubrication problem. Here’s What My New K20 Engine Looks Like Inside video playing Here’s What My New K20 Engine Looks Like Inside .

Why does my car make a tapping sound when I Change Oil?

Simply changing your oil can also get rid of the tapping sound, as over time an engine that is neglected of maintenance will begin to clog up its oil filters meaning that a build-up of grime can again lead to a lack of component lubrication.

Why does my Ford F-150 make a tapping noise?

The contact owns a 2004 Ford F-150. The contact stated that the engine hesitated on several occasions and that there was a tapping noise that progressed. The vehicle was taken to an independent mechanic, who replaced the spark plugs, fuel injectors and the plug wires.

Why does my Ford truck make a clicking noise?

Yesterday driving down a major highway in northern virginia traveling at 65 mph my truck started making a noise from the engine and shut off , I had good oil pressure ,water temp was fine I pulled it off the highway, never to start again. I had it towed to a locale Ford dealer in fairfax va.

Is it normal for an engine to make a ticking noise?

Engine ticking noises are fairly common, and they can be either really bad news or not very serious, depending on the cause. In some cases, they can even be completely normal. Let’s run through some possibilities, starting with the most urgent. This is the most severe — and potentially costly — cause of a ticking engine.

Why did my Mercedes Benz COMAND stop working?

The fiber optic cables are used to transmit the sound signal of your Mercedes-Benz between the different units for better sound quality and faster transfer rates. When one of your components goes down, your COMAND will stop functioning. You need to figure out which component is defective by bypassing each component until you find the problem.

What do you call rear suspension clunking noise?

Rear shock replacement detailed on demand video available for here: https://mercedessource.com/store/merc… This is known as the “dead body in the trunk” sound. A number of owner’s have reported this sound particularly on the W211 chassis. Kent explains what he did to fix it in this 2004 E500 sedan.

Why does my car make a thumping noise when I hit the brakes?

If the groove is interrupted, the shoes snap back, hitting the backing plate. This phenomenon happens very quickly, causing a thumping noise that will drive you crazy and wondering if your car is falling apart or even safe to drive. There are several ways to fix this noise. One is to replace the rear drums.

What causes excessive cabin vibration in a Mercedes Benz?

Failed engine mounts can cause excessive cabin vibrations. Ball joint / front control arm. Ball joints, sway bar link, control arm bushings on used Mercedes-Benz wear out much sooner than you would expect. This is based on our experience with used Mercedes-Benz.

How can you tell if a Mercedes Benz is rusted out?

We still remember an older Mercedes-Benz 240D that had over 1 million miles still running strong but the floor had rusted out, and you can see the ground when sitting on the driver seat. The newer Mercedes-Benz models still have rust issues as well. Get a flashlight and carefully inspect the car. Look under the wheel wells and near the bumpers.

What are the most common problems with Mercedes Benz cars?

8 Most Common Mercedes-Benz Problems 1 Rust. Rust behind license plate / trunk area. 2 Engine Mounts. Engine mounts on Mercedes-Benz cars are oil filled. 3 Suspension & Steering Components. Ball joint / front control arm. 4 Window Regulators. Broken window regulator on Mercedes C-Class. 5 AirMatic Components.

What was the worst problem with the Mercedes Benz E350?

Worst 2006 Mercedes-Benz E350 Problems #1: Balance Shaft Failure 2006 E350 Average Cost to Fix: $4,800 #2: Leaking Fuel Tank Gasket 2006 E350 Average Cost to Fix: $1,200 #3: Car Jerks When Downshifting 2006 E350 Average Cost to Fix: $6,000

Top 5 Mercedes-Benz no start problems 1 Engine Click, No Start 2 Engine Dies Right After It Starts 3 Car turns over, but it won’t start 4 The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery 5 Key will not turn the ignition More …

What does it mean when the shifter is stuck on a Mercedes?

Shifter can not be returned to Park (P), and you can’t remove the key from ignition. P,N,R,D gear selection indicator on dashboard not displaying correct gear. Mercedes-Benz cars that are equipped with automatic transmission have a gear selector shifter interlock safety feature.

What causes a Mercedes Benz to not move out of Park?

If the shifter on your Mercedes-Benz will not move out of park, the first thing your should check is the battery. Once you confirm the battery is fully charged the two most common problems are a defective brake light switch or a shifter module is damaged.

https://www.youtube.com/watch?v=X3ZybBQjk_c

How does auto close work on a Mercedes Benz?

Older Mercedes-Benz models before 1995 will most likely not have the auto close feature. They may have a micro switch on the window regulator that the window toggles on and off when it reaches the top or bottom position. When I park or turn off the car and try to close the windows, they do not go up all the way.

How does power window work on Mercedes Benz?

Remember that these wires don’t just register voltage, but send data. You press a window switch, it sends a signal to the module saying you want to roll it down, which relays to the main brain to decide if it is ok to roll, which relays back to the module to go ahead and roll it down.

How can I synchronize my windows on my Mercedes?

Close the winodws all the way and continue to hold the window switch in “CLOSE” position for an additional 5 seconds. Usually, you will hear a small click when the windows -resynchronize. Tried the window synchronization feature but my windows still don’t work.

How to close the window on a Mercedes CLA?

Push and hold down the window switch, not the whole way for express down, but just to get it down… when all the way down, keep holding for 2 seconds and you should hear a double click. Now pull up on the switch to close, again not the express function, but just rolling it up, hold for 2 seconds again and it should click again.

Older Mercedes-Benz models before 1995 will most likely not have the auto close feature. They may have a micro switch on the window regulator that the window toggles on and off when it reaches the top or bottom position. When I park or turn off the car and try to close the windows, they do not go up all the way.

Close the winodws all the way and continue to hold the window switch in “CLOSE” position for an additional 5 seconds. Usually, you will hear a small click when the windows -resynchronize. Tried the window synchronization feature but my windows still don’t work.

Is the driver’s side window on a Merc working?

MERC’s Owned: G320, GL450, C230 Kompressor, 300E. Dark Helmet: You’re a Gentleman and a Scholar! So this evening I got in my car and the automatic roll up on the driver’s side window is not working. I can roll the window up by keeping my finger on the button, but it will not go up by itself.

Why does my Mercedes Benz rear deck Rattle?

There is a metal ball that rattles around. I strongly recommend wrapping the the outside of the unit (NOT THE INSIDE) with sound deadening material…DO NOT remove the ball. This will stop the noise by 90%. If this helped you give me a thumbs up and definitely subscribe to my channel; I would love to have you in this community!

How can I stop the rattle of my seat belt?

Its actually the center seat belt. There is a metal ball that rattles around. I strongly recommend wrapping the the outside of the unit (NOT THE INSIDE) with sound deadening material…DO NOT remove the ball. This will stop the noise by 90%.

Problem. When you turn the steering wheel on your Mercedes-Benz you may hear a loud squeaking or weird whining noise. The noise is a common problem, with Mercedes Benz E-Class, S-Class, C-Class and ML-Class and it is most noticeable when you first start up the car. Typically the engine is cold. Can often be heard when you are a stop light.

Why do you hear a rattle in your Mercedes Benz?

The parking shoes had worn the friction right off and the shoe hardware had broken allowing the entire rear shoe assembly to become loose enough to rattle under the disc rotor. New shoes and hardware was needed so we updated the set on both sides, completed a sturdy road test and let the Mercedes Benz get back on the road safe and sound.

When you turn the steering wheel on your Mercedes-Benz you may hear a loud squeaking or weird whining noise. The noise is a common problem, with Mercedes Benz E-Class, S-Class, C-Class and ML-Class and it is most noticeable when you first start up the car. Typically the engine is cold. Can often be heard when you are a stop light.

Why are my wipers not working on my Mercedes?

It is common for the fuse to burn out if you press the window switch to active the wipers, but the wipers have frozen, or there is snow on the windshield. Replacing the fuse may be all that you need to do to fix the wiper problem on your Mercedes-Benz.

Where are the fuses on a Mercedes windshield wiper?

Your Mercedes-Benz has three to four fuse boxes. They are located on the side of the dashboard, engine bay, rear seat or even in the trunk. Find the fuse chart for your car and locate the corresponding fuse for the windshield wiper motor. Make sure the fuse is not burned out.

Why are my windshield wipers moving so slow?

This problem is common and is typically caused by defective Light and Rain Sensor for Automatic Headlights and Windshield Wipers. If this sensor is defective, the wipers may move too fast or slow for no reason. The solution to this problem would be to replace the rain sensor.

What kind of problem does a Mercedes C230 have?

21 people found this helpful. Folks I have a 1997 C230 Mercedes, This seems to be having the same problem, but when it Idles it runs rough and when driving it is stalling out but will re-start. I had the codes checked, came up with bad cam sensor.

What makes a wheel hub make a clicking noise?

If it doesn’t, you may have a bad wheel bearing. Here are a few other sounds and symptoms of bad wheel hub bearings: Snapping or clicking noises. This is sometimes also caused by a damaged CV joint, but can also be due to worn wheel bearings if you hear a clicking noise when turning. Humming or growling noises.

What are the symptoms of a bad camshaft position sensor?

Symptoms of a Bad or Failing Camshaft Position Sensor. $79.99 – $89.99. Average rating from 4,829 customers who received a Check Engine Light is on Inspection. The camshaft position sensor gathers information about the vehicle’s camshaft speed and sends it to the vehicle’s engine control module (ECM).

Why does my Mercedes make a tapping noise when I start the car?

It makes the taps when the car is started, even if the AC is off. The taps are the climate control unit normalizing the servos. I checked out the info on the AC system, but it doesn’t give any hints as to how to remove the dash assemby.

Why does my C200 make a knocking noise?

On the Mercedes C200 and actually most Mercedes Benz passenger car models, that all share the long lived 5 link rear suspension set up, there can be several causes. The first potential cause to eliminate is wear to the anti-roll bar bushes or sway-bar (US).

What’s the clunking noise from the rear of my car?

Q: Clunking noise from the rear passenger side when going over uneven roads or bumps. Hi there! So I’ve been hearing clunking noise from my car lately.

Where does the clicking sound come from when turning a wheel?

Recently but not all the time, when I turn my wheel to either side, there is a clicking sound coming from the front, presumably from the axel… Actually, im not sure where the sound comes from so i dont want to speculate but has anyone come across this or heard of this before? Any help would be appreciated.

How does the Mercedes C Class Coupe work?

The sporty C-Class Coupe displays its state-of-the-art innovations and turbocharged power in a muscular frame with the power to seduce. Control in your hands. A world of features are as close as your thumbs. Two smartphone-like pads on the steering wheel let you scroll, swipe and select what you see on the car’s two vivid screens.

Recently but not all the time, when I turn my wheel to either side, there is a clicking sound coming from the front, presumably from the axel… Actually, im not sure where the sound comes from so i dont want to speculate but has anyone come across this or heard of this before? Any help would be appreciated.

Why does my clk350 make a bad noise?

A low speed (5 ~ 25mph), rhythmic, low frequency frictional “groan” could also come from your tires, are they evenly worn out, some brands and types can have these “bad” noises after a certain mileage even low (~15000 – pirelli scorpio…I had on my XC90).

Are there any problems with the CPO clk350?

Newbie MB owener – I purchased a 2007 CPO clk350 five days ago and I’m planning to take it back to the dealer after experiencing two irritating issues. First one – after braking to a complete stop on a slight incline/ uphill this car would roll back the moment the brake was released – potentially dangerous and definitely annoying at the very least.

How is the sound system in a Mercedes Benz?

Mercedes-Benz uses fiber optic cables to transmit the sound signal between the different units. Fiber optics provides a faster transfer rates and better sound quality. All the audio related systems in the car are connected via the fiber optic cable in series, forming a ring or a loop.

The fist thing you should try is to do a soft reset of the COMAND unit. To do a reset you will need to remove the fuses for at least 10 min for these systems: By removing the fuses for these systems, you will be forcing the command unit to perform a rest.

Why does my Mercedes Benz not play MP3s?

-Can’t get MP3 discs to read correctly in the in-built CD player (though I admit I’m not sure if this just means MP3 decode is broken or if the in-built slot isn’t meant to play MP3s regardless….) Where is the amp? Is it under the psgr seat or is it in the trunk?

Im really thinking that the LCABs are the culprit. The factory tech visually spotted the cracks in them, but when he pried against them with a long prybar, there wasnt (in his opinion) enough play to warrant immediate replacement. A second opinion at a local German independent said the same thing.

Are there any problems with the Mercedes C320?

Common Problems The most common problem with the Mercedes C320 concerns its 3.2-liter 215-horsepower V-6 engine. Affecting all model years apart from the 2006 version–and most severe with the 2001 and 2002 years–the problem lies specifically with its mass air flow sensor, which the engine uses to measure the amount of air it consumes.

Hint: Starter Problem or Low Battery This may seem obvious, but an old battery is the root of many headaches and can cause all sorts of malfunctions on Mercedes-Benz cars. How old is the battery on your Mercedes-Benz?

What causes a Mercedes Benz to not start?

In most cases you will get a fault code related to one of the following: 1 ECM / PCM computer failure 2 Camshaft position sensor 3 Shifter Selector module 4 Fault codes related to driver authorization or immobilizer 5 Electrical problems

Why does my Jeep Wrangler make a loud clicking sound?

Enter your ride HERE to be a part of JUNE’s Ride of the Month Challenge! Hey everyone. So yesterday when I started the Jeep, there was a loud clicking sound coming from behind the passenger side dash. It was about 5-8 loud clicks after the engine started. It has been doing this with every start, and occasionally while driving as well.

Why is my Fuse Box making a clicking noise?

This can be caused by a computer failure, resistance in the ground wire for the control side of the relay or high resistance in the power supply to the control side of the relay. To find out the source of the problem, you’ll need to run some quick tests using a multimeter.

Why does my CLK W209 make a clicking noise?

I have a CLK W209 which has a clicking noise in the dash when the ignition is turned to position 2, it only lasts for about 30 seconds. Someone has suggested it is the air distribution flaps being set and thinks there is a way of doing a re set to stop the noise ?

What causes a clicking noise in the center of the dash?

Problem Description A repetitive clicking noise from behind the center area of the dash panel is usually caused by a broken stepper motor actuating arm. The actuating arm controls the direction of air flow in the climate control system.

Where does the noise come from on an air conditioner?

In most new air conditioners, the bulk of the noise comes from the compressor. You can remove the top of your A/C outdoor unit and install a sound blanket over the compressor — it just sits right on top of it. This will muffle much of the sound of the unit.

What does it mean when your AC is making a pulsating noise?

An air conditioner making a pulsating noise isn’t necessarily a bad sign — a little pulsing noise can be perfectly normal when the air conditioner is operating. But if your outdoor A/C unit is making a pulsating noise that you can hear from inside the house, it could be a sign that something has come loose inside the unit and needs to be replaced.

What does it mean when your a / C unit is running but not cooling?

If your A/C unit seems to be running outside but isn’t cooling inside, the problem is likely a refrigerant leak. This may or may not be accompanied by any telltale noises, depending on how bad the leak is and where it’s located. 5.

Why does my air conditioner make a clicking noise?

If air conditioning could be totally silent, most people would love summer even more. Other folks enjoy a little white noise courtesy of the air conditioner blowing. Nobody wants a repetitive, annoying sound like clicking, though. Air conditioner clicking sounds can be categorized (and fixed) based on where the sound comes from.

Why does my air conditioner keep getting stuck?

Another common problem is the air conditioner vent flap getting stuck. This is typically due to a worn out of failed vent flap motor. If it is indeed the linkage that’s broken, you have to replace it.

My 2002 C230K with 71K on it has recently developed a loud tapping noise which emanates from the dash behind the radio/climate control. At the same time the ventilation system will no longer blow air through the dash vents. The defroster and foot vents still work.

Why is my a / C making a clicking noise?

The noise you are hearing is one of the HVAC door actuators that control air flow or temperature for the a/c. There are at least 4 of these actuators in your system and one of them is going bad and would need to be replaced. The one that is making the noise It’s hard to specify wxactly which one without checking the system first hand.

Why does my car make a loud popping sound when I start the engine?

A blown exhaust gasket can cause some pretty loud sounds from that area, but it will always be louder and faster as you rev the engine higher. In some cases you may hear an exhaust leak like this when you first start the engine but, as it warms up it seems to magically seal itself!

Why do I hear a ticking noise in my car?

Gravity will keep what oil there is further down in the engine. If oil isn’t reaching the top of your engine, you’ll begin to hear a higher-pitched ticking or tapping noise. More often than not, this is coming from the engine’s valve train components like lifters, rockers, camshafts and cam adjusters.

What kind of noise does a Buick LeSabre make?

Buick LeSabre bad knocking noise coming from the engine. Have a 2005 Lasabre 3.8. Had a bad knocking noise coming from the engine. Took off the belt and started it up no more noise. Replaced the harmonic balancer still have the noise with the belt on. Noise goes away if you run the engine at a higher rpm . Car has only 62,000 miles.

Is it bad if your car makes a ticking sound while running?

But if your engine has started making a ticking sound while running, it probably has you worried about both your car and your pocketbook. Engine ticking noises are fairly common, and they can be either really bad news or not very serious, depending on the cause. In some cases, they can even be completely normal.

Why is my oil pump making a ticking sound?

Double-check that youre using the correct filter, and if youre not, consider switching to the manufacturer-supplied part. The flow rate through a generic filter could be incorrect, creating insufficient engine oil pressure. The worst-case scenario is that your oil pump is slowly dying and you need a replacement.

What to do about tapping noise in dashboard?

IT STARTS WHEN THE CAR IS STARTED AND STOPS AFTER A SERIES OF TAPS. IF YOU DISCONNECT IT MAYBE YOU CAN STOP THE NOISE. For the AC stepping motor I fix the footwell flap in the correct position then pull out the cable plug of stepping motor.

Brief, loud clicking noise from dashboard area when AC is… Q: Brief, loud clicking noise from dashboard area when AC is turned on. This started happening about 2 weeks ago. When I start up my car or whenever I turn the AC on I hear 3 or 4 loud clicks coming from what seems to be under the dashboard.

IT STARTS WHEN THE CAR IS STARTED AND STOPS AFTER A SERIES OF TAPS. IF YOU DISCONNECT IT MAYBE YOU CAN STOP THE NOISE. For the AC stepping motor I fix the footwell flap in the correct position then pull out the cable plug of stepping motor.

Is it normal to hear knocking noises in your car?

Some knocking noises are normal and should be of no concern at all, while other deep noises can be a sure sign of impending doom. These are the noises that should be attended to immediately. How can you determine whether the engine noises you are hearing are good or bad?

Why do I hear knocking noises in my diesel engine?

From my years of troubleshooting diesels, I have learned the very best way to determine if the internal noises you are hearing are normal or not is to do a Diesel Purge. Let me explain; most of the typical knocking and pinging in a diesel engine comes from injector “nailing” and ignition knock.

How to stop ticking noise from Mercedes engine?

Basically you’ll open the pass airbad cover by breaking the straps, remove the airbad (remember to disconnect the battery first) and the will expose the valve. It is pretty cramped but with some patience it is doable. The alternative – and remommended MB way – is to remove the whole dash.

Why is my Mercedes Benz clunking and popping?

Neither did replacing the steering damper. Last couple of days the temps have risen to high 80’s. Went for a drive into the city (Georgetown section of DC) in a lot of traffic the other day, and the clunking/popiing was definitely more pronounced in the heat.

What are the common problems with Mercedes diesels?

Here are some common problems that affect many Mercedes-Benz diesel models including E350, ML350, GL350, R350, Sprinter, R320 CDI and BlueTec models. Common problems Diesel Particulate Filter. As Mercedes DPF traps and holds soot, with time it reaches a point when it needs to be ‘emptied out’. This is done by regeneration.