Why does my Jeep 93 engine not start?

93 4.0l engine won’t start (usually) SOLVED!! Jeep died the other day. Just quit. Classic Crankshaft Position Sensor symptoms, Right? Replaced the replacement CPS, still nothing. Swapped out PCM (ECM, ECU) Still the same. My problem is similar to others here, but mine will start sometimes. Completely randomly. Cranks fine.

Is the Jeep Grand Cherokee 4.0 with no start?

Come along with Eric O. at SMA as he has a look at this 2001 Jeep Grand Cherokee with the I6 4.0 that was towed in with a crank, no start condition. It didn’t take long to figure out this common problem and solve the infamous P0320 crank sensor code.

Why does my Jeep 4.0L have no spark?

It’s almost impossible for all 6 COP ignition coils to fail at the exact same time… so the most likely cause for this no spark condition is a bad crankshaft position sensor. But before you go out and replace the crank sensor, you need to test it (to make sure it’s fried).

Why does my Jeep Cherokee not turn on?

Symptoms don’t get more straightforward than this: The truck doesn’t start. Turn the key, and everything comes on, but the driveway is absent of that Jeep rumble. When you turn the key, a number of things happen. First, the key-switch engages the vehicle’s accessory systems like the radio.

What causes no start on a jeep 4.0L?

Updated: 29 June 2019. Article Id: 420. A no start condition, on your 4.0L Jeep, is usually caused by a lack of fuel, or a lack of spark, or a lack of air (generally engine compression).

When did the Jeep Cherokee XJ come out?

The Jeep Cherokee (XJ) is a compact SUV that was manufactured and marketed by Jeep from 1997 to 2001. Sharing the name of the original full-size SJ model, but without a traditional body-on-frame chassis, the XJ instead featured a light-weight unibody design.

Is there a problem with the ignition on a Jeep Cherokee?

If there is one common denominator amongst practically all 1984 to 1996 Jeep Cherokees (XJ , ZJ, WJ and WK’s alike) it is a bad ignition. Though typically robust, most Jeep Cherokees will eventually experience ignition failure, leaving otherwise happy owners stranded.

Is there a vacuum leak in the Jeep Cherokee 4.0?

A common problem in the 4.0 jeep engines is vacuum leaks around the throttle body. Here’s the solution I found for the HUGE vacuum leak in my 2000 Cherokee. Category Autos & Vehicles Show moreShow less Loading… AutoplayWhen autoplay is enabled, a suggested video will automatically play next. Up next

Why does my Harley Davidson crank but not start?

There have been a few reports of a P1009 code – incorrect password also. It appears the turn signal and stalls or cranks but will not start. Try removing the ecm and security fuses, wait ten minutes and reinstall the fuses. This “reboots” the turn signal module and the motorcycle will then start from that point on.

What does it mean when your Honda Civic won’t start?

Does Not Crank Condition: Means that the engine is not cranking when you turn the key to crank the engine. In other words, the engine doesn’t turn over at all. This is usually due to a bad starter motor, bad ignition switch, bad neutral safety switch, or the engine is locked up.

Why does my tantonio 4.0L engine not start?

Tantonio had a similar issue at EJS a few years ago, turned out to be both a bad CPS and a bad coil. We have a club member who’s having stalling issues with his ’94. Low fuel pressure, probably a bad pump. Put a pressure gauge on the system, pull the vacuum line of thr pressure regulator and & see what the total fuel pressure is.

Why does my YJ Wrangler not start up?

A common problem with YJ Wranglers – turn the key and it doesnt start or it takes a few minuted to fire up Sometimes called “Lazy PCM”. Some simple tips and a certain way to tell if it is you ECM going south.

What should fuel pressure be in Jeep 93?

Put a pressure gauge on the system, pull the vacuum line of thr pressure regulator and & see what the total fuel pressure is. Should be 39 psi, 31 psi with the vacuum line attached to the regulator. r u using jeep factory parts or after market parts?? cam sensor… in the distributor. *Getting good spark, so Guessing it’s not the coil.

What to do if your engine won’t start?

Replaced the replacement CPS, still nothing. Swapped out PCM (ECM, ECU) Still the same. My problem is similar to others here, but mine will start sometimes. Completely randomly. Cranks fine. Usually doesn’t start, but it has on a couple occasions, and when it does, it idles fine. The other day, after sitting, it started up.

What should I do if my Jeep Wrangler wont start?

If the battery seems to be intact, you cannot identify the noises your engine makes when it is started and you cannot discover any defective cables or an empty tank, you should leave the diagnosis to experts. In the workshop, a mechanic can probably find out what the problem is in no time and then get rid of it.

When did the Jeep Wrangler YJ come out?

know your wrangler. For the 1987 model year, AMC introduced the first Jeep Wrangler (YJ) to the market, which Chrysler continued to produce after the buy out in 1987. It replaced the AMC CJ-7, with very little change in terms of the body and frame. The most notable, and controversial change was the square headlamps.

Where is the timing scale on a Jeep Wrangler?

Locate the timing scale on the case cover above the crankcase pulley at the engine front end and the notch on the crankcase pulley or vibration dumper, right next to the timing scale. If they are hard to see, clean the scale plate and pulley. Then highlight the marks with white chalk or correction fluid.

What kind of transmission does a YJ Wrangler have?

The 2.5 liter straight 4 w/manual transmission was always paired with the AX-5. The TF 904 automatic transmission option was only made available from 94-95. Both straight 6 motors were matched with the TF 999 for the entire production run.

What should the fuel pressure be on a 94?

We have a club member who’s having stalling issues with his ’94. Low fuel pressure, probably a bad pump. Put a pressure gauge on the system, pull the vacuum line of thr pressure regulator and & see what the total fuel pressure is. Should be 39 psi, 31 psi with the vacuum line attached to the regulator.

Why does my Jeep turn over but does not start?

Cranks But Does Not Start Condition: In this type of condition, you turn the key and the engine in your Jeep cranks (turns over) but it doesn’t start (run). The usual suspects, that can cause this type of problem, are a bad fuel pump, bad crank sensor, bad ignition coil (if your Jeep is distributor equipped), etc.

What kind of ignition system does a Jeep Cherokee use?

The ignition system is the one tasked with creating and delivering spark to each of the 6 cylinders. Without spark, the engine will crank but no start. The ignition system of the Jeep vehicles covered by this tutorial use either a distributor type system or a COP (Coil-On-Plug) ignition coil system. Failed ignition coil.

What should the battery reading be on a Jeep Wrangler?

Batteries use CCA (Cold Cranking Amps) to measure starting power. Be aware that your battery could have power, however, when under load, the cranking amps are not powerful enough to get the starter to crank the engine. A good fully charged battery should read over 12.6 volts. If the battery reads 12.45 volts or less, it is low.

What to do if your Jeep Wrangler battery won’t start?

The first starting point when diagnosing a dead battery is to verify your battery has the correct voltage. Incorrect or low power to the starter will not start your Jeep. Batteries use CCA (Cold Cranking Amps) to measure starting power.

How to repair the fuel gauge on a Jeep Wrangler?

Pull the relay panel lid off. Pull out the old fuel sensor relay. If you are unsure of its location, consult the relay diagram on the inside of the relay panel’s lid. Plug the new sensor in and replace the relay panel lid. Replace your Jeep’s negative battery cable. “Haynes Jeep Wrangler 1987-2003 (Haynes Manuals) “; Mike Stubblefield; 2005

How do you replace an engine in a jeep?

Choose the correct engine to replace the one currently in your vehicle (ie: Jeep 4.0L engine), then when you’re ready to return your core, ATK simplifies the process with their 360-Degree Core Guarantee. Simply place your old engine in the crate the new one came in and call the pickup number provided.

How to reset your Jeep engine control module?

3- Once the time has passed you should now turn the headlights “on” and “off” twice to drain the Engine Control Module from any remaining power. 4- Now plug back in the negative terminal and your Jeep ECM should now be reset. To finish off this post , here are a couple of things you should keep in mind.

What to do when your engine has no spark?

Insert a spark plug tester into the plug boot and ground it on a piece of metal on the engine. Finally, Have someone crank the engine and watch for spark. Remove one of the coils from the spark plug. Use an extra spark plug. A spark plug tester. Or even a screwdriver in the end of the coil.

Why does my car not start when I crank the engine?

The crankshaft position (CKP) sensor monitors the position or rotational speed of the crankshaft. If the crankshaft position sensor has failed completely, and isn’t sending a signal to the (ECU) at all, then the computer won’t send any fuel to the injectors. This will leave you unable to start the car.

What causes a car to have no spark?

In my experience, the most common component failures, of the ignition system that cause a no start-no spark Condition are: Failed ignition coil. Bad distributor cap (if distributor equipped). Bad distributor rotor (if distributor equipped).

Can a spark test be done on a no start Jeep?

Testing for spark can very easily and safely be done with a dedicated spark tester. If the ignition system is the cause of the cranks but does not start condition, you’re not gonna’ see spark at any of the 6 spark plug wires or 6 COP ignition coils.

Navigation